Sunstream Evolve Mini Manuale utente
Assembly Manual
Australia - 1800 316 962 | New Zealand 0800 21 8020
Prepare & Position the Sauna Floor
If you are assembling your sauna on a hard surface
floor it is recommended that you apply the included
adhesive felt pads to the bottom of the sauna floor.
Place the sauna floor in the desired location.
It is necessary to position the floor out from your walls for assembly and move the sauna following assembly.
It is important that the sauna floor is level. Checking with a large level is recommended. If the floor is not
level, shimming or other remedies should be applied before assembling the sauna.
Australia - 1800 316 962 | New Zealand 0800 21 8020
Left Side Wall
Place the Left Side Wall on your floor behind the
sauna Floor Base.
Front Wall
Insert the Front Wall (with window) into
the channel in the sauna Floor Base
Australia - 1800 316 962 | New Zealand 0800 21 8020
Front Left Corner
Connect the Left Side Wall to the Front Wall by raising the Front Wall approx 1/2" then sliding down
to connect the 2 fasteners.
Cinch the two walls together by applying pressure on the outside of the Side Wall with the inside of
your knee.
Hold Left Side Wall DOWN while sliding Front Wall UP.
It is helpful if the second person applies pressure against the opposite edge of the Front Wall. This
will help ensure that the two walls remain in contact and the fasteners will connect.
Front Wall
NOTE: It is NOT necessary to lift the entire Front Wall. Simply slide the Front Wall upward at
the front corner of the sauna to connect to the Side Wall
Australia - 1800 316 962 | New Zealand 0800 21 8020
Fasteners
It may be be that your sauna's fasteners (Tab and Keyhole) are installed opposite to those pictured. In
such a case, the Wall which slides up will be opposite to that shown.
Guiding Rule: Always slide the Wall with the Tab fastener UP then DOWN on to the Wall with the
Keyhole fastener.
There are two sets of fasteners to join the saunas' corners together. After lowering the front wall, check to
ensure that both sets of fasteners have connected by looking at the corner inside of the sauna. It is
possible to connect one set of fasteners and miss the other. If there is an obvious gap in the corner
between the two walls the fasteners have not connected and the raising and lowering procedure will need
to be repeated.
The wall with the Tab Fastener always
slides UP then DOWN on to the wall with
the Keyhole fastener
Australia - 1800 316 962 | New Zealand 0800 21 8020
Back Left Corner
Repeat the procedure to connect
the Back Wall to the Left Side Wall
Raise the Wall will the Tab Fastener
approx 1/2" then slide down to
connect the 2 fasteners.
Cinch the two walls together by
applying pressure on the outside of
the Side Wall with the inside of your
knee.
Position Right Side Wall (with door)
Insert the Right Side Wall into the channel in
the Floor Base
Back Wall
Back Wall
Australia - 1800 316 962 | New Zealand 0800 21 8020
Back Right Corner
Connect the Back Wall to the Right Side Wall Raise the
Wall will the Tab Fastener
approx 1/2" then slide down to connect the 2 fastenersl
Cinch the two walls together by applying pressure on
the outside of the Side Wall with the inside of your knee.
Front Right Corner
Repeat the procedure to connect the Right
Side Wall to the Front Wall
Australia - 1800 316 962 | New Zealand 0800 21 8020
Connect the Front Wall heater electrical
lead to the floor base.
Ensure that the connector is fully inserted and that the
threaded cuff is fully screwed onto the Floor Base
connector.
Under-Bench Electrical
NOTE: Do not connect main power
cord to your wall outlet at this time.
Australia - 1800 316 962 | New Zealand 0800 21 8020
Connect the circular connector to
Power Supply Box.
Align the groove in connector to
properly insert. Thread the cuff of
the connector on fully.
Attach the 'D-Sub' computer
style connector as shown.
Plug in all heater leads to the
receptacles in the Power Supply Box.
Feed the main Power Supply Cord in through the hole in the Back Wall and
insert in Power Supply Box.
Do NOT plug Power Cord into your wall outlet until all electrical connections are finished inside of the sauna
and for the Roof.
Australia - 1800 316 962 | New Zealand 0800 21 8020
Remove Side Wall
Heater Guards
The wooden lattice work in front of the heaters
is referred to as the heater guard. These are
held in place with strong magnets.
It is necessary to remove the heater guards from
the two side walls in order to install the leg heater
and the sauna bench.
Leg Heater
Install the Leg Heater by lowering it into the holding
brackets mounted on the side walls.
Plug the Leg Heater into the power supply box in floor.
Australia - 1800 316 962 | New Zealand 0800 21 8020
Indice
Altri manuali Sunstream Prodotto idraulico
Sunstream
Sunstream evolve 30 Manuale utente
Sunstream
Sunstream evolve EHS Manuale utente
Sunstream
Sunstream Evolve 30 Manuale utente
Sunstream
Sunstream Mini Manuale utente
Sunstream
Sunstream Supreme One Manuale utente
Sunstream
Sunstream Evolve 20 Manuale utente
Sunstream
Sunstream Evolve 20 EHS Manuale utente
Sunstream
Sunstream evolve 10 Manuale utente
Sunstream
Sunstream Evolve Mini EHS Manuale utente
Sunstream
Sunstream Evolve 10 EHS Manuale utente
