Supermicro C7H270-CG-ML Manuale utente

C7H270-CG-ML

C7Q270-CB-ML

ENGLISH

繁體中文

简体中文

日本語

(

한국어

QUICK REFERENCE GUIDE

Revision 1.0

All manuals and user guides at all-guides.com

all-guides.com

C7H270-CG-ML/C7Q270-CB-ML QUICK REFERENCE GUIDE Product Safety Information

Standardized Warning Statements

Motherboards

About Standardized Warning Statements

The following statements are industry standard warnings, provided to warn the user of situations which can potentially

cause a bodily injury. Should you have questions or experience difculty, contact Supermicro's Technical Support De-

partment for assistance. Only certied technicians should attempt to install or congure components.

Read this section in its entirety before installing or conguring components in the Supermicro chassis.

Battery Handling

Warning!

There is a danger of explosion if the battery is replaced incorrectly. Replace the battery only with the same or an equiva-

lent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions.

電池の取り扱い

電池交換が正しく行われなかった場合、破裂の危険性があります。交換する電池はメーカーが推奨する型、または同等のも

のを使用下さい。使用済電池は製造元の指示に従って処分して下さい。

警告

電池更換不當會有爆炸危險。請使用製造商建議之相同或功能相當的電池更換原有電池。請按照製造商的說明指示處理

廢棄舊電池。

警告

电池更换不当会有爆炸危险。请只使用同类电池或制造商推荐的功能相当的电池更换原有电池。请按制造商的说明处理

废旧电池。

경고!

배터리가 올바르게 교체되지 않으면 폭발의 위험이 있습니다. 기존 배터리와 동일하거나 제조사에서 권장하는 동등한

종류의 배터리로만 교체해야 합니다. 제조사의 안내에 따라 사용된 배터리를 처리하여 주십시오.

Note: For complete product safety information, refer to http://www.supermicro.com/about/policies/safety_information.cfm.









All manuals and user guides at all-guides.com

C7H270-CG-ML/C7Q270-CB-ML QUICK REFERENCE GUIDE BIOS POST Code

AMI BIOS POST Codes

About AMI BIOS POST Codes

The table below lists some of AMI BIOS POST codes for C7H270-CG-ML and C7Q270-CB-ML. For more informa-

tion, refer to https://www.supermicro.com.tw/manuals/other/AMI_BIOS_POST_Codes_for_Grantley_Motherboards.pdf.

Code Description

0x32 CPU post-memory initialization is started

0x55 No Memory detected or memory failed

0x63 CPU DXE initialization is started

0x69 North Bridge DXE initialization is started

0x70 South Bridge DXE initialization is started

0x92 PCI Bus initialization is started

0x99 Super IO Initialization

0x9A USB initialization is started

0xA0 IDE initialization is started

0xA9 Boot into BIOS setup menu

0xAE Legacy Boot event

0xB2 Legacy Option ROM Initialization

0xB4 USB hot plug

0xD6 No VGA device

0xD7 No Keyboard plug in

0xF2 Recovery process started

0xF9 Recovery capsule is not found

All manuals and user guides at all-guides.com

C7H270-CG-ML/C7Q270-CB-ML

QuiCk RefeRenCe Guide Rev. 1.0

SUPERMICR R

Motherboard Layout and Features

= mounting hole

LGA 1151

I/O BACK PANEL

TPM/PORT80JTPM1:

JTPM1

RST PWR

XOH/FF

NIC

PWR

LED

HDD

LED

JF1

USB 2/3USB 8/9(3.0)

2-3:BIOS RECOVERY

1-2:NORMAL

JBR1

WATCH DOG

1-2:RST

2-3:NMI

JWD1:

JBR1

JPME2

AUDIO FP

COM1

JD1:SPEAKER :1-4

JD1

JSD1

JWD1

JL1

JSD1:SATA DOM PWR

JL1:

CHASSIS

INTRUSION

2-3:ME MANUFACTURING MODE

JPME2:

1-2:NORMAL

I-SATA5

I-SATA4

I-SATA3

I-SATA2

I-SATA1

I-SATA0

PCH SLOT1 PCI-E 3.0 X1

JBT1

JBT1:CMOS CLEAR

PCH SLOT2 PCI-E 3.0 X4

CMOS

BUTTON

CLEAR

POWER

RESET

J9702

SYS_FAN1

JSTBY1

J9701

JI2C1

JI2C2

JSPDIF_OUT

5V STBY POWER

JSTBY1:

CPU SLOT3 PCI-E 3.0 X16

OFF:DISABLE

JI2C1/JI2C2

ON :ENABLE

HD AUDIO

PCIE M.2

CONNECTOR 1

SYS_FAN2

USB 6/7(3.0)

LAN

CPU

JPW1

DVI

JPUSB1:USB0/1 WAKE UP

HDMI/DP

DIMMB2

DIMMA2

DIMMB1

DIMMA1

2-3 DISABLE

1-2 ENABLE

CPU_FAN1

JVR1

JPUSB1 JPW2

KB/MOUSE

LED1

RT1

REV: 1.01

C7H270-CG-ML

DESIGNED IN USA

MAC CODE

BAR CODE

BIOS LICENSE

A C

USB 4/5(3.0)

USB 0/1

2280

2260

2242

7th/6th Gen

Intel® CoreTM i7/i5/i3

Series CPU

All manuals and user guides at all-guides.com

Package contents

• One (1) Supermicro Motherboard

• Two (2) SATA Cables, One (1) I/O Shield

• One (1) Quick Reference, One (1) Driver CD

Jumpers and Connectors

Jumpers

Connectors

Jumper Description Default

CLEAR CMOS Clear CMOS Button Push Button Switch

JBR1 BIOS Recovery 1-2: Normal

JBT1 Clear CMOS (on board) Short pads to clear CMOS

JI2C1/JI2C2 SMB to PCI-E Slots On: Enable

JPME2 Intel® Manufacturing Mode 1-2: Normal

JPUSB1 USB Wake Up Enable (Back Panel USB 0/1) 1-2: Enable

JWD1 Watch Dog Function Enable 1-2: RST

POWER BUTTON Internal Power Button Push Button Switch

RESET BUTTON Onboard System Reset Button Push Button Switch

Connector Description

AUDIO FP Front Panel Audio Header

BT1 Onboard Battery

COM1 COM1 Port Header

CPU_FAN1 CPU Fan Headers

I-SATA0~5 (Intel® PCH) Serial ATA (SATA) 3.0 Ports 0~5 (6Gb/sec)

JD1 Pin 1~4: External Speaker

JF1 Front Panel Control Header

JL1 Chassis Intrusion Header

JPW1 24-pin ATX Power Connector (Required)

JPW2 8-pin CPU Power Connector (Required)

JSD1 SATA DOM (Disk On Module) Power Connector

JSPDIF_OUT Sony/Philips Digital Interface (S/PDIF) Out Header

JSTBY1 Standby Power Header

JTPM1 Trusted Platform Module (TPM) Header

PCI-E M.2 CONNECTOR 1 PCI-E M.2 Connector 1, small form factor devices and other portable devices for

High speed NVMe SSDs

SYS_FAN1/FAN2 System Fan Headers

USB 2/3 Front Panel Accessible USB 2.0 Headers

USB 8/9 (3.0) Front Panel Accessible USB 3.0 Header

All manuals and user guides at all-guides.com

ContaCt InformatIon

• www.supermicro.com (Email: [email protected])

• Manuals: http://www.supermicro.com/support/manuals

• Drivers & Utilities: ftp://ftp.supermicro.com

• Safety: http://www.supermicro.com/about/policies/safety_information.cfm

LED Indicators

LED indicators

CPU & Memory Support

DIMM Memory Installation

LED Description Color/State Status

LED1 Power On

S3 (Suspend to RAM) LED

Power On: Green On

S3: Green Blinking See manual

The C7H270-CG-ML/C7Q270-CB-ML supports a 6th and 7th generation Intel® CoreTM i7/i5/i3/Pentium®/Celeron®

processor, up to 64GB of Unbuffered (UDIMM) non-ECC DDR4 memory, up to 2400MHz in four 288-pin memory

slots. Populating these DIMM slots with a pair of memory modules of the same type and same size will result in

interleaved memory, which will improve memory performance.

Towards the CPU

Memory Population Guidelines

When installing memory modules, the DIMM slots should be populated in the following order: DIMMA2, DIMMB2,

then DIMMA1, DIMMB1.

• Always use DDR4 DIMM modules of the same size, type and speed.

• Mixed DIMM speeds can be installed. However, all DIMMs will run at the speed of the slowest DIMM.

Recommended Population (Balanced)

DIMMB2 DIMMA2 DIMMB1 DIMMA1 Total System Memory

4GB 4GB 8GB

4GB 4GB 4GB 4GB 16GB

8GB 8GB 16GB

8GB 8GB 8GB 8GB 32GB

16GB 16GB 32GB

16GB 16GB 16GB 16GB 64GB

DIMMB2 (Red Slot)

DIMMA2 (Red Slot)

DIMMA1 (Black Slot)

DIMMB1 (Black Slot)

Note: 1) For memory optimization, use only DIMM modules that have been validated by Supermicro. For the latest memory updates, please

refer to our website at http://www.supermicro.com/products/motherboard.

2) Always connect the power cord last, and always remove it before adding, removing or changing any hardware components.

All manuals and user guides at all-guides.com

all-guides.com

MNL-1914-QRG-100

micro's written consent. All Trademarks are property of their respective entities. All information provided is deemed accurate at the time of printing;

however, it is not guaranteed.

Notes

• Graphics shown in this quick reference guide are for illustration only. Your components may or

may not look exactly the same as drawings shown in this guide.

• Refer to Chapter 2 of the User Manual for detailed information on jumpers, connectors, LED

indicators, memory support and CPU/motherboard installation instructions.

Front Panel Control (JF1)

CPU Installation Heatsink Installation

Heatsink

with Fan

Motherboard

Mounting Hole

Back Panel I/O Connectors

Add

thermal paste

Power Button

Over heat/Fan Fail L

ED (-)

NIC1 LED (-)

Reset Button

HDD LED (-)

POWER LED (-)

Reset

PWR

POWER LED (+)

Ground

HDD LED (+)

NIC1 LED (+)

Over heat/Fan Fail L

ED (+)

1516

A. PS/2 Keyboard/Mouse Port G. USB 3.0 Port 4 L. Center/LFE Out

B. USB 2.0 Port 0 H. USB 3.0 Port 5 M. Surround Out

C. USB 2.0 Port 1 I. RJ-45 Gigabit Ethernet Port N. SPDIF Out

D. DisplayPort J. USB 3.0 Port 6 O. Line In

E. HDMI Port K. USB 3.0 Port 7 P. Line Out

F. DVI-D Port Q. Mic In

All manuals and user guides at all-guides.com

美超微電腦股份有限公司

C7H270-CG-ML/C7Q270-CB-ML

快速參考指南版本 1.00

SUPERMICR R

主機板元件配置圖

TPM/PORT80JTPM1:

JTPM1

RST PWR

XOH/FF

NIC

PWR

LED

HDD

LED

JF1

USB 2/3USB 8/9(3.0)

2-3:BIOS RECOVERY

1-2:NORMAL

JBR1

WATCH DOG

1-2:RST

2-3:NMI

JWD1:

JBR1

JPME2

AUDIO FP

COM1

JD1:SPEAKER :1-4

JD1

JSD1

JWD1

JL1

JSD1:SATA DOM PWR

JL1:

CHASSIS

INTRUSION

2-3:ME MANUFACTURING MODE

JPME2:

1-2:NORMAL

I-SATA5

I-SATA4

I-SATA3

I-SATA2

I-SATA1

I-SATA0

PCH SLOT1 PCI-E 3.0 X1

JBT1

JBT1:CMOS CLEAR

PCH SLOT2 PCI-E 3.0 X4

CMOS

BUTTON

CLEAR

POWER

RESET

J9702

SYS_FAN1

JSTBY1

J9701

JI2C1

JI2C2

JSPDIF_OUT

5V STBY POWER

JSTBY1:

CPU SLOT3 PCI-E 3.0 X16

OFF:DISABLE

JI2C1/JI2C2

ON :ENABLE

HD AUDIO

PCIE M.2

CONNECTOR 1

SYS_FAN2

USB 6/7(3.0)

LAN

CPU

JPW1

DVI

JPUSB1:USB0/1 WAKE UP

HDMI/DP

DIMMB2

DIMMA2

DIMMB1

DIMMA1

2-3 DISABLE

1-2 ENABLE

CPU_FAN1

JVR1

JPUSB1 JPW2

KB/MOUSE

LED1

RT1

REV: 1.01

C7H270-CG-ML

DESIGNED IN USA

MAC CODE

BAR CODE

BIOS LICENSE

A C

USB 4/5(3.0)

USB 0/1

2280

2260

2242

= 裝機孔

LGA 1151

I/O BACK PANEL

7th/6th Gen

Intel® CoreTM i7/i5/i3

Series CPU

All manuals and user guides at all-guides.com

單一主機板包裝盒內容清單

•Supermicro

c7H270-cG-mL/c7Q270-cB-mL

主機板x1

•SATA 訊號線 x2

•後檔板 x1

• 快速參考指南 x1

• 驅動程式光碟片x1

連接埠說明

AUDIO FP 前面板音效接頭

BT1 內建電池

COM1 COM1 序列連接埠

CPU_FAN1 CPU （中央處理器）風扇接頭

I-SATA0~5 （Intel®PCH）序列 ATA介面（SATA 3.0）連接埠 0~5（6Gb/秒）

JD1 針腳 1~4：外接喇叭

JF1 前面板接頭

JL1 機殼防盜裝置接頭

JPW1 24針腳ATX主電源連接埠（必備）

JPW2 8針腳CPU電源連接埠（必備）

JSD1 SATA DOM (磁碟模組) 電源連接埠

JSPDIF_OUT S/PDIF（索尼/飛利浦數位傳輸介面）輸出接頭

JSTBY1 待機電源接頭

JTPM1 TPM 信任平台模組接頭

PCI-E M.2 CONNECTOR 1 PCIe M.2 介面連接埠，適用具高速傳輸NVMe介面之小尺寸以及其他可攜式

M.2 固態硬碟

SYS_FAN1/FAN2 系統風扇接頭

USB 2/3 前面板USB 2.0 規格連接埠

USB 8/9 (3.0) 前面板USB 3.0 規格連接埠

跳線器/連接埠

連接埠（Connector）

跳線器說明預設值

CLEAR CMOS CMOS（可讀寫隨機存取記憶體晶片）組態資料清除按鍵式開關

JBR1 BIOS 復原針腳 1-2 （正常）

JBT1 CMOS 組態資料清除（內建）設為短路來清除CMOS資料

JI2C1/JI2C2 PCI-E（系統匯流排）介面的 SMB 插座啟用

JPME2 Intel®製造模式針腳 1-2 （正常）

JPUSB1 啟用USB喚醒（背板USB 0/1）針腳 1-2 （啟用）

JWD1 啟動系統監控（Watch Dog）功能針腳 1-2 （重設）

POWER BUTTON 電源開關按鍵式開關

RESET BUTTON 系統重設按鍵式開關

跳線器（Jumper）

All manuals and user guides at all-guides.com

線上技術支援及下載

• 聯絡我們（技術支援信箱）：www.supermicro.com （Email: [email protected]）

• 產品手冊文件：http://www.supermicro.com/support/manuals

• 驅動程式及工具程式：ftp://ftp.supermicro.com

• 產品安全性須知：http://www.supermicro.com/about/policies/safety_information.cfm

本主機板

C7H270-CG-ML/C7Q270-CB-ML

支援第六代與第七代 Intel® CoreTM i7/i5/i3/Pentium®/

Celeron®處理器。記憶體支援Unbuffered DIMM non-ECC DDR4，容量最高可達64GB，及四個高

達2400MHz

（

288支針

）

的記憶體插槽。欲取得雙通道效能，請安裝成對相同型號與速度之記憶體。

LED 指示燈

CPU & Memory Support

中央處理器及記憶體支援

此面朝向中央處理器

DIMMB2 （紅色插槽）

DIMMA2 （紅色插槽）

DIMMA1 （黑色插槽）

DIMMB1 （黑色插槽）

DIMM（記憶體模組）安裝方式

LED燈說明燈號顏色/情況狀態

LED1 開啟/S3模式（待機）指示燈開機：綠燈

待機S3模式：綠燈閃爍參閱手冊

請依照以下說明及表格安裝記憶體模組：

• 請遵循下列插槽編號順序依序安裝：

DIMMA2（通道A、插槽2）、DIMMB2（通道B、插槽2）　　

　、

DIMMA1 （通道A、插槽1）、DIMMB1 （通道B、插槽1）。

• 請使用相同型號（DDR4 DIMM）與速度之記憶體。若混合使用不同速度之記憶體，系統將依

　較低的記憶體速度執行。

建議插槽使用方式

DIMMB2 DIMMA2 DIMMB1 DIMMA1 系統記憶體總容量

4GB 4GB 8GB

4GB 4GB 4GB 4GB 16GB

8GB 8GB 16GB

8GB 8GB 8GB 8GB 32GB

16GB 16GB 32GB

16GB 16GB 16GB 16GB 64GB

註：1) 請安裝使用本公司所認可的記憶體模組以達記憶體模組最佳化。更多的記憶體模組相關訊息，請參閱本公司網頁

(http://www.supermicro.com/products/motherboard)。

2) 增加、移除和更換任何硬體元件前，請務必先拔掉電源線，待確實完成所有程序後，再重新連接電源線。

All manuals and user guides at all-guides.com

Altri manuali per C7H270-CG-ML

Questo manuale è adatto per i seguenti modelli

Indice

Lingue:

Altri manuali Supermicro Scheda madre

Supermicro

Supermicro P3TDDE Manuale utente

Supermicro

Supermicro X11DSF-E Manuale utente

Supermicro

Supermicro X8DTN+ Manuale utente

Supermicro

Supermicro X10DRG-H Manuale utente

Supermicro

Supermicro Super X6DHR-TG Istruzioni per l'installazione e il funzionamento

Supermicro

Supermicro X11DDW-L/NT Manuale utente

Supermicro

Supermicro X11SCW-F Manuale utente

Supermicro

Supermicro X10QBL-4CT Manuale utente

Supermicro

Supermicro C7Z270-PG Manuale utente

Supermicro

Supermicro X13SAQ Manuale utente

Supermicro

Supermicro SUPER P3TSSE Manuale utente

Supermicro

Supermicro SUPER P6SWA Manuale utente

Supermicro

Supermicro X11SPG-TF Manuale utente

Supermicro

Supermicro X7DBR-8 Plus Manuale utente

Supermicro

Supermicro SUPER P4SBA+ Manuale utente

Supermicro

Supermicro PDSMA Manuale utente

Supermicro

Supermicro Supero X10SRL-F Manuale utente

Supermicro

Supermicro Supero X7DBN Manuale utente

Supermicro

Supermicro X11SSL-nF Manuale utente

Supermicro

Supermicro X10SRi-F Manuale utente

Supermicro

Supermicro H8SSL-i Manuale utente

Supermicro

Supermicro P4SCA Manuale utente

Supermicro

Supermicro SUPERO X10DRD-iTP Manuale utente

Supermicro

Supermicro SUPER P4SGR Manuale utente

Manuali Scheda madre popolari di altre marche

DFI

DFI SD170 Manuale utente

ASROCK

ASROCK ROMED8-2T Manuale utente

Asus

Asus P2L97A Manuale utente

Winmate

Winmate IC70 Manuale utente

Asus

Asus MES-B Manuale utente

Grantech

Grantech SYS8F377VGGA-3OMN Manuale utente

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuale utente

Gigabyte

Gigabyte GA-9IVDT Manuale utente

Texas Instruments

Texas Instruments ADS8372EVM Manuale utente

Commell

Commell MS-C73 Manuale utente

IBT Technologies

IBT Technologies MB860 Manuale utente

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuale utente

Biostar

Biostar M7VIT Bravo Istruzioni per l'uso e l'installazione

Intel

Intel D33217CK Manuale utente

Asus

Asus F1A55-M LX PLUS R2.0 Manuale utente

EPC

EPC EPC9147C Manuale utente

Asus

Asus EX-B760M-V5 D4 Manuale utente

EPOX

EPOX MU-8KHA0010 Manuale utente