SUPPO OSD V3.71 Manuale utente

SUPPO OSD V3.71 10HZ/current sensor

Connetion Pins

Connector’s description

Current

sensor

To the add-on

Current sensor

from SUPPO

RSSI

Connect to your radio receiver’s

RSSI port

Config panel

Connect to

button panel

Main Batt

(to RC plane’s

battery)

Connect to your airplane’s battery

pack (monitor plane’s voltage

Max 28V).

As 11.7v shown on left)

Video In

To you

Camera

Video out

For the OSD video output

GPS

To the GPS

unit supplied

Power in

Connect to power source for your

OSD

(as Voltage 4.5V shown on left)

Configuring OSD:

Press button “Menu”on “Config Panel”to enter system configuration

Use “Option SW”and “Select”button to configure

Button and Light

“Home”

Record home location, Max RSSI,

Clear timer, clear distance value

“Menu”

Enter configuration menu

“Switch”

Switch between configuration options

“Select”

Select each Option’s value

“Reset”

Restart OSD

Signal Light

Off : No power;

On: connecting GPS, waiting for GPS signal;

Flash: working good

Typical FPV with OSD set up:

1. Camera ------- ‘Video in”OSD “Video out”to ---- Suppo V-Tx , video transmitter.

2. Connect GPS, and Main Batt wire to --- RC main battery

3. Connect RSSI to your RC Receiver (Warning: potential dangerous, could damage your

RX. not recommend to do so if you don’t well understand your Radio RX)

4. Connect 9-12V power to Suppo V-tx to power up Suppo V-Tx, OSD and the camera.

Important Notice, care fully check the power wire connect Camera, OSD and Video Tx.

Wrong power wiring could damage your camera OSD and video transmitter.

Important: Never mix up the Video input (VI) wire with the Video output wire (marked VO),

otherwise, it could damage your cam or video transmitter!

System Config menu

description

NTSC ENABLE

0 –Disabled (for PAL)

1 –Enabled (for NTSC)

DISPLAY MODE

0 –Longitude and Latitude

1 –GMT time

Current Sensor

0 –No Current sensor

Will not show any current

infomation

1 –Current sensor connected

Current consumption

information shown

UNIT MODE

0 –Unit at meter (km when

over 10km),

Speed in km/h

1 –display Unit at feet (mile

when over 10mile),

speed in mph

Setting RSSI Min –Max value:

1. On ground power up TX and RX, press “set home”button, OSD will record RSSI

Max;

2. On ground, power off TX, press “Menu”button, OSD will record RSSI Min value.

3. Select Save and Exit to save RSSI Min Max value.

Notes:

GPS first start will take 1 minute. Re-start only 10 second.

Please note that you need to set “HOME”location (press home button) each time to get

the right “Flight Distance”and “Home Distance”, and “Return Course”

Specifications:

Input Volt

Weight

Size

OSD

5-12V

49*33*6.5m

GPS

3.3V

10g

Current Sensor

7-35V, 100A

31*35mm

Power consumption：Max：1.1W

Plane battery detect max 28V

Altri manuali SUPPO Unità di controllo

SUPPO

SUPPO OSD v3.51 Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente