Symbol SYMBOL LS7808 Manuale utente
Symbol LS7808 Horizontal Slot Scanner
Mounting Instructions and EAS Installation Guide
2 Symbol LS7808 Horizontal Slot Scanner
©2007 MOTOROLA, INC. All rights reserved.
Motorola reserves the right to make changes to any product to improve reliability,
function, or design.
Motorola does not assume any product liability arising out of, or in connection
with, the application or use of any product, circuit, or application described herein.
No license is granted, either expressly or by implication, estoppel, or otherwise
under any patent right or patent, covering or relating to any combination, system,
apparatus, machine, material, method, or process in which Motorola products
might be used. An implied license exists only for equipment, circuits, and
subsystems contained in Motorola products.
MOTOROLA, the Stylized M Logo and Symbol and the Symbol logo are
registered trademarks of Motorola, Inc. Other product names mentioned in this
manual may be trademarks or registered trademarks of their respective
companies and are hereby acknowledged.
Motorola, Inc.
One Motorola Plaza
Holtsville, N.Y. 11742-1300
http://www.symbol.com
Warranty
For the complete Motorola hardware product warranty statement, go to:
http://www.symbol.com/warranty.
Patents
This product is covered by one or more patents. For patent information go to:
http://www.symbol.com/patents.
Mounting Instructions and EAS Installation Guide 3
Introduction
This guide includes two sections: Section I provides scanning
information, typical layouts, installation/mounting information and
mounting dimensions for the Symbol LS7808-SR20007TCR and
LS7808-SR2X009SCR horizontal slot scanners; Section II provides
installation instructions for EAS.
Configurations
The Symbol LS7808 is available in the following configurations.
NOTE If you are replacing a Symbol LS5800-I200TC or
LS5800-I200TN scanner with the Symbol
LS7808-SR20007TCR or LS7808-SR2X009SCR, mounting
buckets are interchangeable.
Configuration Features
Symbol LS7808-SR20007TCR Standard (tin oxide) glass window; twilight
black; Checkpoint
®
EAS; RoHS compliant.
Symbol LS7808-SR20009SCR Scratch proof (sapphire) glass window;
stainless steel bezel top; Checkpoint
®
EAS;
RoHS compliant.
Symbol LS7808-SR22009SCR Scratch proof (sapphire) glass window;
stainless steel bezel top; Checkpoint
®
EAS;
RoHS compliant; Remote Scanner
Management (RSM) ready “out of the box.”
A stainless steel in-counter mounting kit (p/n 12-17206-02R) is required for all
models. See
Installation/Mounting on page 6
for mounting/installation
instructions.
4 Symbol LS7808 Horizontal Slot Scanner
Section I - Scanning, Layouts, Mounting
Active Scan Area
The Symbol LS7808 is designed to be installed in the counter, with the
face of the scanner flush with the counter top.
The figure below shows a typical layout. The dotted area depicts the
active scan area and the arrow shows the optimal direction of product
flow. The scanner’s active scan zone extends about 6 in. (15.24 cm)
above the window and is angled at approximately 38° from the counter.
Typical Layouts
The illustrations below show typical Symbol LS7808 installations
with various options, as noted. For best operating results, locate
the power supply at least 4 in. (10.16 cm) below the scanner
chassis or 2 in. (5.08 cm) away laterally.
Scanner
Window
Product Flow
Mounting Instructions and EAS Installation Guide 5
Without Auxiliary Scanner and EAS
With Auxiliary Scanner
Scanner
Host
Power Supply (optional)
Synapse Cable
(Optional)
Host Interface Cable
Scanner
Host
Power Supply
Synapse Cable
(Optional)
Host Interface Cable
6 Symbol LS7808 Horizontal Slot Scanner
With EAS
Installation/Mounting
The Symbol LS7808-SR20007TCR and LS7808-SR2X009SCR require
a stainless steel in-counter mounting kit (p/n 12-17206-02R) for
installation. There are two options for installing this model using the
kit, also known as a bucket. The steps for installation options A and B
follow.
Scanner
Host
EAS
Antenna Box
Synapse Cable
(Optional)
Host “Y” Cable
Power Cable (optional)
Power Supply (optional)
EAS Control Cable
EAS Control Box
Mounting Instructions and EAS Installation Guide 7
Option A - Resting on the Counter Top
1. Cut a hole in the counter 6.26 in. (159 mm) square, as shown in the
illustration below.
2. Place the bucket into the hole.
3. Unscrew and remove the scanner connector cover.
4. Place the scanner on the counter near the bucket.
5. Route the cables from beneath the hole and attach to the scanner
as shown in Typical Layouts on page 4.
6. Reattach the connector cover and tighten the screws.
7. Lower the scanner into the bucket.
IMPORTANT Always reattach the connector cover and tighten the
screws after all cables are connected to the scanner ports. The
connector cover ensures that all cables are properly situated and
connections are secure.
Counter Hole 6.81 in. ±0.06
173 mm ±1.5
~3.5 in.
89 mm
7.91 in.
201 mm
6.26
159
8 Symbol LS7808 Horizontal Slot Scanner
Option B - Flush with the Counter Top
1. On the counter top, measure two concentric squares: an inside
square of 6.81 in. (173 mm) and an outside square of 7.91 in. (201
mm), as shown in the illustration below.
2. Cut out the 6.81 in. (173 mm) inner square.
3. With a router set to a depth of .05 in. (1.2 mm), route out the outside
square. The corner radius should not exceed 0.2 in. (5 mm). Ensure
the outside square is concentric with the inside square.
4. Place the bucket into the hole.
5. Unscrew and remove the scanner connector cover.
6. Place the scanner on the counter near the bucket.
7. Route the cables from beneath the hole and attach to the scanner as
shown in Typical Layouts on page 4.
8. Reattach the connector and tighten the screws.
9. Lower the scanner into the bucket.
IMPORTANT Always reattach the connector cover and tighten the
screws after all cables are connected to the scanner ports. The
connector cover ensures that all cables are properly situated and
connections are secure.
R 0.20 in. max
R 5 mm max
7.91 in. min
201 mm min Counter Hole 6.81 in. ±0.06
173 mm ±1.5
7.91 in.
201 mm
~3.5 in.
89 mm
0.27 in
6.8 mm
0.39 in min
10 mm min
7.91 in.
201 mm
~3.5 in
.
89 mm
Mounting Instructions and EAS Installation Guide 9
Section II - Electronic Article Surveillance (EAS)
The Symbol LS7808-SR20007TCR and LS7808-SR2X009SCR include
an EAS antenna. The scanner and EAS system can operate
independently of each other, or using an exclusive interlock feature. The
deactivation range is mapped suitable to the scanning range, so both
can be accomplished almost simultaneously. The interlock feature
requires a good decode signal to activate the EAS system.
The scanner’s integrated EAS deactivation antenna requires an EAS
host cable. This Y-cable connects to the scanner’s host port at one end
and splits to the host and the EAS system at the other end.
Checkpoint® EAS Model Compatibility
The EAS cable is intended for use with Checkpoint CP-VII and CP-IX
systems. It does not support CP-IV and other low-power receiver-based
EAS deactivation systems.
Considerations
The Checkpoint EAS system operates by generating a periodic burst of
energy which deactivates EAS tags brought into proximity of the
scanner. Unless proper precautions are taken, this field may interfere
with the scanner’s operation.The following criteria must be observed
when installing EAS:
• The antenna box must be as far as possible (minimum 6 in. or
15.24 cm) from the scanner.
• The scanner (with integrated EAS antenna), EAS antenna box, EAS
control cable and EAS controller box must be as far as possible from
the scanner’s host and power cables. For a typical EAS installation,
see Typical Layouts on page 4.
• The counter in which the EAS antenna is installed must be made of
non-metallic materials. Metallic counters or metal objects in proximity
to the scanner interfere with EAS Deactivation.
CAUTION Do not attempt to activate the interlock feature. Activation
instructions are for a Symbol qualified technician only.
10 Symbol LS7808 Horizontal Slot Scanner
• If two antenna boxes are connected to the controller box, each of
them must be connected to a scanner (antenna). If one is left
unconnected, communications errors may occur. If only one antenna
is in use, disconnect the other antenna box at the controller box.
Deactivation for Sensormatic EAS System
To interface to Sensormatic systems, contact Symbol Product
Management.
Connecting the EAS Antenna
A host interface cable with EAS leads from Symbol is required. The EAS
leads are connected by Checkpoint Systems, Inc.
Contact your local Checkpoint representative to install the EAS cable to
the Checkpoint Deactivation System. To contact a representative, call
800-257-5540 (in the United States) or 609-848-1800 (outside the United
States).
Connecting the EAS Interlock
To activate the EAS system independent of the scanner, or combine the
two in an exclusive interlock feature, refer to the appropriate parameters
in the Symbol LS7808 Horizontal Slot Scanner Product Reference
Guide, p/n 72E-73952-xx.
The interlock feature discourages “sweetheart shopping.” These are
instances where some customers are favored and not all items are
scanned. The interlock prohibits the deactivation of the EAS tag without
the item being scanned first.
Altri manuali per SYMBOL LS7808
1
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Symbol Lettore di codici a barre
Symbol
Symbol LS4278 Manuale di istruzioni
Symbol
Symbol LS 5800 Manuale utente
Symbol
Symbol LS3578 Manuale utente
Symbol
Symbol 3100 Series Manuale di installazione e funzionamento
Symbol
Symbol CS3070 Manuale utente
Symbol
Symbol SYMBOL DS6707 Manuale di installazione e funzionamento
Symbol
Symbol LT 1810 Manuale utente
Symbol
Symbol LS 4008i Manuale di installazione e funzionamento
Symbol
Symbol LS1900 Series Manuale utente
Symbol
Symbol LS 1006 Manuale di installazione e funzionamento
Symbol
Symbol P 470 RF Manuale utente
Symbol
Symbol LS 1220 Manuale di installazione e funzionamento
Symbol
Symbol LS 4208 Manuale utente
Symbol
Symbol CSM 150 Manuale utente
Symbol
Symbol LS1203 Manuale di installazione e funzionamento
Symbol
Symbol Symbol LS2208 Manuale utente
Symbol
Symbol LS 3070 Manuale di installazione e funzionamento
Symbol
Symbol SPS 3000 Series Manuale
Symbol
Symbol RS409 Manuale utente
Symbol
Symbol DS 3408 Manuale di installazione e funzionamento
Manuali Lettore di codici a barre popolari di altre marche
POSMicro
POSMicro Datalogic PowerScan D7100 Manuale utente
Marson
Marson MT780 Guida rapida alla configurazione
NCR
NCR RealPOS Manuale utente
Motorola
Motorola SE3300 Guida rapida alla configurazione
Element
Element P130BT Manuale utente
Motorola
Motorola Symbol LS3008 Manuale di installazione e funzionamento
