SystemBase Eddy Series Manuale utente

Eddy Series

User’s Guide

Ver 2.1

2008.4.2

Tel: 82-2-855-0501 / Fax: 82-2-855-0580

16F Daerung Post Tower-1, Guro-dong, Seoul, Korea

[email protected]/

http://www.sysbas.com/

Table of Contents

Table of Contents ................................................................... I

Figures.......................................................................................... III

Ta b l e s ........................................................................................... IV

Chapter 1. Introduction ......................................................... 1-1

1.1 About this manual.......................................................................1-1

1.2 Who should read this manual .........................................................1-1

1.3 Contents ..................................................................................1-2

1.4 Eddy Documents.........................................................................1-2

1.5 Technical Support .......................................................................1-3

Chapter 2. Getting Started ..................................................... 2-1

2.1 Overview .................................................................................2-1

2.2 Features ..................................................................................2-5

2.3 Package Checklist .......................................................................2-7

2.4 Applications ..............................................................................2-7

Chapter 3. Hardware Description .............................................. 3-1

3.1 Eddy-CPU .................................................................................3-1

3.1.1 Dimensions ................................................................................3-2

3.1.2 Pin Specifications.........................................................................3-3

3.2 Eddy-S1/Pin ..............................................................................3-1

3.2.1 Dimensions ................................................................................3-2

3.2.2 Pin Specifications.........................................................................3-3

3.2.3 Serial Interface Setup....................................................................3-6

3.2.4 Terminal Resistors ........................................................................3-7

3.2.5 Terminal Resistor Installation Guide...................................................3-7

3.3 Eddy-S1/DB9 .............................................................................3-8

3.3.1 Dimensions ................................................................................3-9

3.3.2 Pin Specifications....................................................................... 3-10

3.4 Eddy-S1/DB9-PoE...................................................................... 3-14

3.4.1 Dimensions .............................................................................. 3-15

3.4.2 Pin Specifications....................................................................... 3-16

3.5 Eddy-S2M/Pin .......................................................................... 3-20

3.5.1 Dimensions .............................................................................. 3-21

3.5.2 Pin Specifications....................................................................... 3-22

3.5.3 Eddy-S2M/Pin JIG (Pin-to-DB9 gender).............................................. 3-26

Chapter 4. Integration ........................................................... 4-1

4.1 Connection Guide .......................................................................4-1

4.2 First-time Bootup ...................................................................... 4-2

4.3 Connecting to Eddy with IP address ................................................. 4-3

4.4 Eddy-S2M/Pin’s MCI & USB Host Port ................................................ 4-6

Chapter 5. Configuration via Web ............................................. 5-1

5.1 Connection .............................................................................. 5-1

5.2 Setup Menu .............................................................................. 5-2

5.3 Network Settings ....................................................................... 5-3

5.4 Serial Settings........................................................................... 5-5

5.5 GPIO Settings ........................................................................... 5-9

5.6 Change Password ...................................................................... 5-11

5.7 Update Firmware...................................................................... 5-13

5.8 Factory Default ........................................................................ 5-15

5.9 Save & Reboot ......................................................................... 5-16

Chapter 6. Configuration via Telnet ........................................... 6-1

6.1 Connection .............................................................................. 6-1

6.2 View commands ........................................................................ 6-2

6.3 Network commands .................................................................... 6-2

6.4 Serial Commands ....................................................................... 6-3

6.5 GPIO commands ........................................................................ 6-6

6.6 Username/Password Commands ..................................................... 6-6

6.7 System Commands ..................................................................... 6-6

Chapter 7. Appendix ............................................................. 7-1

7.1 Firmware Updates...................................................................... 7-1

7.2 Eddy-CPU ................................................................................ 7-3

7.3 Eddy-Serial .............................................................................. 7-4

7.4 Eddy-Memory............................................................................ 7-5

7.5 Ordering Information .................................................................. 7-6

7.6 Package Contents ...................................................................... 7-6

7.7 FCC Statement.......................................................................... 7-7

III

Figures

Figure 2-1 Eddy-CPU................................................... 2-1

Figure 2-2 Eddy-S1/Pin ............................................... 2-2

Figure 2-3 Eddy-S1/DB9............................................... 2-2

Figure 2-4 Eddy-S1/DB9-PoE ........................................... 2-3

Figure 2-5 Eddy-S2M/Pin .............................................. 2-3

Figure 2-6 Eddy-DK ................................................... 2-4

Figure 2-7 Eddy Software Architecture.................................. 2-5

Figure 3-1 Eddy-CPU front and side view................................ 3-2

Figure 3-2 Pin Spec ................................................... 3-3

Figure 3-3 Eddy-S1/Pin – Product and block diagram...................... 3-1

Figure 3-4 Eddy-S1/Pin Front View ..................................... 3-2

Figure 3-5 Eddy-S1/Pin Side View ...................................... 3-2

Figure 3-6 RS485 Terminal Registor ..................................... 3-7

Figure 3-7 Eddy-S1/DB9 – Product Picture and Block Diagram .............. 3-8

Figure 3-8 Eddy-S1/DB9 Front View .................................... 3-9

Figure 3-9 Eddy-S1/DB9 Side View ..................................... 3-9

Figure 3-10 Eddy-S1/DB9-PoE – Product Picture and Block Diagram ......... 3-14

Figure 3-11 Eddy-S1/DB9-PoE Front View................................ 3-15

Figure 3-12 Eddy-S1/DB9-PoE Side View................................. 3-15

Figure 3-13 Eddy-S2M/Pin – Product Picture and Block Diagram ............ 3-20

Figure 3-14 Eddy-S1/DB9-PoE Front View................................ 3-21

Figure 3-15 Eddy-S1/DB9-PoE Side View................................. 3-21

figure 3-16 Eddy-S2M/Pin Pin Spec ..................................... 3-22

figure 3-17 J8 PIN header ............................................. 3-23

figure 3-18 J9 PIN header ............................................. 3-24

figure 3-19 Eddy-S2M/Pin JIG .......................................... 3-26

Figure 4-1 Connecting to the default IP address ......................... 4-3

Figure 5-1 Eddy Login Page ............................................ 5-1

Figure 5-2 Main Page.................................................. 5-2

Figure 5-3 Network Settings Configuration Page ........................... 5-3

Figure 5-4 Serial settings page ......................................... 5-5

Figure 5-5 Eddy-S1/Pin - GPIO Settings Page ............................. 5-9

Figure 5-6 Eddy-CPU - GPIO Settings Page .............................. 5-10

Figure 5-7 Change Password Setting Page............................... 5-11

Figure 5-8 After changing the password ................................ 5-12

Figure 5-9 Update Firmware Setting Page .............................. 5-13

Figure 5-10 Firmware update in progress............................... 5-14

Figure 5-11 Firmware update complete ................................ 5-14

Figure 5-12 Factory Default Page ....................................... 5-15

Figure 5-13 Save & Reboot Page ........................................ 5-16

Figure 6-1 Connection via Telnet ........................................ 6-1

Figure 7-1 Firmware updates via FTP .................................... 7-1

Figure 7-2 Firmware Update via Telnet ................................... 7-2

Tables

Ta b l e 1 - 1 Eddy Documents ............................................ 1-2

Ta b l e 5 - 1 Main features of Setup Menu ................................. 5-2

Ta b l e 5 - 2 Main features of General Configuration........................ 5-3

Ta b l e 5 - 3 Main features for Network Service Configuration ............... 5-4

Ta b l e 5 - 4 Main features for Serial Settings .............................. 5-5

Ta b l e 5 - 5 Main features for GPIO Settings ............................. 5-10

Ta b l e 5 - 6 Main features for Save & Reboot............................. 5-16

Ta b l e 6 - 1 def view commands ......................................... 6-2

Ta b l e 6 - 2 Network commands ......................................... 6-2

Ta b l e 6 - 3 Serial commands ........................................... 6-3

Ta b l e 6 - 4 GPIO commands ............................................ 6-6

Ta b l e 6 - 5 User/Password configurations ................................ 6-6

Ta b l e 6 - 6 System Commands .......................................... 6-6

Chapter 1. Introduction

SystemBase Embedded Module lineup is composed of largely three catagories; Eddy-Serial Series,

Eddy-DIO Series and Eddy-CPU Series. This manual focuses on Eddy-Serial and Eddy-CPU Series.

1.1 About this manual

This manual includes all necessary information from installation to operating Eddy Series (Eddy-CPU,

Eddy-S1/Pin, Eddy-S1/DB9, and Eddy-S1/DB9-PoE). Setting Eddy’s configurations, status monitoring,

firmware update, and other administration work are also included, H/W level integration and S/W

setting information can also be found.

1.2 Who should read this manual

This guide is designed for Eddy users and administrators. It is strongly recommended that anyone

trying to apply, use, and maintain Eddy read this document. It will be a great starting point for any

administrator who wants to easily monitor and control Eddy and its connected devices.

1-1

Chapter 1. Introduction

1.3 Contents

Chapter 1. Introduction is a preface with general information and introductory notices.

Chapter 2. Getting Started gives a brief introduction to Eddy series, including features and

applications.

Chapter 3. Hardware Descriptions explains the layout and pin specifications with block diagram and

drawings.

Chapter 4. Integration assists you connecting Eddy to serial and network environment. It covers first

time boot-up and status check procedures.

Chapter 5. Configuration via Web provides ways to configure and to connect Eddy via web browser.

Chapter 6. Configuration via Telnet provides commands and its explanation to configure and to

connect Eddy via web Telnet.

Chapter 7. Appendix provides firmware update guides and detailed technical specifications.

1.4 Eddy Documents

The following table summarizes documents included in the Eddy document set.

Table

Eddy Documents

Document Description

User’s Guide Eddy’s Configuration, and Management Information

Programmer’s Guide

Programmer’s application development guide, including in-depth

approach to compiling, linking, creating and uploading firmware

API reference is included with a list of available functions

for customized application programming

Portview User’s Manual Guide for SystemBase device server management application

Portview

COM Port Redirector

User Manual Guide for SystemBase COM Port Redirector

Te s t V i e w

User Manual Guide for SystemBase test program TestView

General information on Eddy or embedded device servers can be obtained at our website at

http://www.sysbas.com/. Latest documents, software and firmware downloads are available.

Other relevant documents are as follows:

1-2

Chapter 1. Introduction

1-3

Document Description

Eddy Spec Sheet Eddy specifications

Eddy White Paper

An introductory reading for anyone new to embedded device

server, which focuses on background, history, market environment,

and technology

Eddy Application Notes Various applications of Eddy presented in diagrams and images

All documents are updated promptly, so check for the recent document updates. The contents in

these documents are subject to change without a prior notice.

1.5 Technical Support

You can reach our tech support by following 4 ways;

1. Visit the developer’s community at http://www.embeddedmodule.com and share information and

tips on Eddy with developers all around the world.

2. Visit us at http://www.sysbas.com/ and go to ‘Technical Support’ menu. FAQ and questions can be

reviewed and submitted.

3. E-mail our technical support team to tech@sysbas.com. Any kind of inquiries, requests, and

comments are welcomed.

4. Call us at our customer center at 82-2-855-0501 for immediate support.

Our technical support team will kindly help you get over with the problem.

Chapter 2. Getting Started

Welcome to Eddy! This chapter includes Eddy series overview, main and distinctive features, package

contents for each product, and application fields.

2.1 Overview

There are 4 modules in Eddy-Serial Series; Eddy-CPU, Eddy-S1/Pin, Eddy-S1/DB9, and Eddy-S1/DB9-

PoE.

Each module includes default applications for serial and LAN communication, and supports plug-and-

play features. By switching to the custom mode, users can program any application and upload it on

to the module. This application then is executed on the module. In order to write and compile

programmer’s source code, Software Development Kit (SDK) LemonIDE®is required. SDK is included in

the Development Kit package. Please refer to Programming Guide and LemonIDE® user’s manual

included in the Development Kit for detailed information on the SDK.

SDK is not necessary for users using Eddy in default presettings.

◆Eddy-CPU

Eddy-CPU is an embedded module based on ATMEL AT91SAM9260-CJ processor with 32MB SDRAM, 4MB

Flash Memory, 1 Ethernet port with 10/100Mbps, 16 bit address / 8 bit data bus interface supporting

external device connection, and maximum 17 programmable IO pins. Programmers can easily

implement RS232/422/485 serial driver or I2C interface with library type example codes and

evaluation kit circuit diagrams.

Eddy-CPU is implemented on a small form factor (42 * 25mm) with on-board memory and integrated

10/100Mbps network interface. Developers can minimize time and cost spent on developing

application products.

Figure 2-1 Eddy-CPU

2-1

Chapter 2. Getting Started

◆Eddy-S1/Pin

RJ-45 Ethernet port is included to provide direct connection to network.

For serial communication, RS232 only or RS422/485 combo interface is available. In the combo

module, RS422/485 setting can be adjusted with software, using web interface.

Acceptable external power input ranges from 3.0 to 5.5V through pin headers.

Please check labeled input voltage on top of the module before supplying power. Improper voltage

feed may damage the module.

Figure 2-2 Eddy-S1/Pin

◆Eddy-S1/DB9

RJ-45 Ethernet port is included to provide direct connection to network.

For serial communication, RS232 only or RS422/485 combo interface is available through DB9 male

connector. In the combo module, RS422/485 setting can be adjusted with software, using web

interface.

External power input is provided as 5V DC Jack.

Please check labeled input voltage on top of the module before supplying power. Improper voltage

feed may damage the module.

Figure 2-3 Eddy-S1/DB9

2-2

Altri manuali per Eddy Series

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali SystemBase Unità di controllo

SystemBase

SystemBase Eddy Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente