Tandberg Data LTO 1 Manuale utente
LTO 1 Magnetic Tape
Cartridge Drive
Setup, Operator, and Service
Guide
LTO 1 Magnetic Tape
Cartridge Drive
Setup, Operator, and Service
Guide
Note
Before using this information and the product it supports, read the information in “Safety and Environmental Notices” on
page v and “Notices” on page 87.
Third Edition (September 2001)
This edition applies to the IBM
®
Ultrium
™
Internal Tape Drive Models T200 and T200F Setup, Operator, and Service
Guide and to all subsequent releases and modifications until otherwise indicated in new editions. This edition
replaces GA32-0435-01.
©Copyright 2000, 2001
Contents
Safety and Environmental Notices .................v
Danger Notice..........................v
Caution Notice .........................v
Attention Notice .........................vi
Laser Safety and Compliance....................vi
Summary of Changes ......................vii
Second Edition .........................vii
Third Edition ..........................vii
Chapter 1. Introduction......................1
SCSI Attachment ........................2
Physical Characteristics of the SCSI Interface .............2
Address Assignments ......................2
Installing, Removing, or Resetting a Drive on an Active SCSI Bus .....3
Fibre Channel Attachment .....................3
Physical Characteristics of the Fibre Channel Interface .........4
Supported Topologies ......................4
Address Assignments ......................4
World Wide Names.......................5
Installing, Removing, or Resetting a Drive on an Active Fibre Channel ....5
Chapter 2. Specifications .....................7
Chapter 3. Installing the Tape Drive .................9
Rear View of the SCSI Drive....................10
Rear View of the Fibre Channel Drive ................11
Step 1. Unpack the Drive .....................11
Step 2. Power-off the Enclosure (Optional)...............11
Step 3. Install the Cooling Fan Assembly (Optional) ...........11
Installing the Cooling Fan onto a SCSI Drive .............12
Installing the Cooling Fan onto a Fibre Channel Drive .........13
Step 4. Set the SCSI ID (SCSI Drive Only) ..............14
Step 5. Terminate the Drive and Supply TERMPOWER (SCSI Drive Only) . . . 15
Step 6. Set the Arbitrated Loop Physical Address (Fibre Channel Drive Only) 15
Setting the Loop ID to Provide Status About the Loop .........16
Setting the Loop ID to Provide Additional Loop IDs ..........18
Step 7. Mount the Tape Drive into an Enclosure.............20
Step 8. Connect Power to the Tape Drive ...............21
Step 9. Perform a Checkout of the Tape Drive .............21
Step 10. Connect the RS-422 Interface ................21
Step 11. Connect the Tape Drive to the SCSI or Fibre Channel Interface . . . 22
Connecting the Drive to a SCSI Interface ..............22
Connecting the Drive to a Fibre Channel Interface ...........22
Step 13. Configure the Tape Drive to the Server, Switch, or Hub.......22
Chapter 4. Operating the Tape Drive ................23
Status Light ..........................24
Unload Button .........................25
Single-character Display .....................26
Inserting a Tape Cartridge.....................26
Removing a Tape Cartridge ....................27
Cleaning the Drive Head .....................27
iii
||||
||||
Placing the Drive in Maintenance Mode................27
Selecting a Diagnostic or Maintenance Function............28
Exiting Maintenance Mode ...................37
Updating the Firmware ......................38
Updating Firmware through the SCSI, Fibre Channel, or RS-422 Interface 38
Updating the Firmware with an FMR Tape Cartridge ..........39
Chapter 5. Using the Media....................41
Data Cartridge .........................42
Cleaning Cartridge .......................42
Setting the Write-Protect Switch ..................43
Reattaching a Leader Pin .....................44
Handling the Cartridges......................48
Environmental and Shipping Specifications for Tape Cartridges .......49
Disposing of Tape Cartridges....................49
Ordering Media Supplies .....................50
Ordering Custom Bar Code Labels ................50
Chapter 6. Resolving Problems ..................51
Methods of Receiving Errors and Messages ..............53
Descriptions and Corrective Actions for Errors and Messages.......53
Using Sense Data.......................59
Obtaining a Drive Dump ....................63
Viewing the Drive Error Log ...................64
Resolving Problems Reported by the Server ..............65
Fixing SCSI Bus Errors .....................65
Fixing Fibre Channel Errors ...................67
Resolving Media-Related Problems .................69
Chapter 7. Servicing the Ultrium Internal Tape Drive ..........71
Removing the SCSI Tape Drive ...................71
Removing the Fibre Channel Tape Drive ...............72
Manually Removing a Tape Cartridge.................73
Fixing an Internal Jam .....................76
Appendix A. Tools and Supplies..................81
Appendix B. TapeAlert Flags ...................83
TapeAlert Flags Supported by the Drive................83
Notices ...........................87
Trademarks ..........................87
Electronic Emission Notices ....................88
Special Considerations for Electromagnetic Compatibility ........88
IBM Ultrium Internal Tape Drive Models T200 and T200F ........88
Getting Help ..........................90
Warranty ...........................90
Related Publications .......................91
IBM Ultrium Publications ....................91
IBM Fibre Channel Publications..................91
Other Publications.......................91
Web Sites..........................92
Glossary ...........................93
Index ............................103
iv IBM Ultrium Internal Tape Drive
||
||
||
||
Safety and Environmental Notices
When using this product, observe the danger, caution, and attention notices that are
contained in this guide. Symbols that represent the severity of the safety condition
accompany the notices.
The sections that follow define each type of safety notice and give examples.
Danger Notice
A danger notice calls attention to a situation that is potentially lethal or extremely
hazardous to people. A lightning bolt symbol always accompanies a danger notice
to represent a dangerous electrical condition. A sample danger notice follows:
DANGER
An electrical outlet that is not correctly wired could place
hazardous voltage on metal parts of the system or the products
that attach to the system. It is the customer’s responsibility to
ensure that the outlet is correctly wired and grounded to prevent
an electrical shock.
Caution Notice
A caution notice calls attention to a situation that is potentially hazardous to people
because of some existing condition. One of several symbols can accompany a
caution notice:
If the symbol is... It means....
A hazardous electrical condition with less severity than an
electrical danger.
A generally hazardous condition not represented by other
safety symbols.
A hazardous condition due to the use of a laser in the
product. Laser symbols are always accompanied by the
classification of the laser as defined by the U. S.
Department of Health and Human Services (for example,
Class I, Class II, and so forth).
v
Sample caution notices follow:
CAUTION:
The controller card contains a lithium battery. To avoid possible
explosion, do not burn, exchange, or charge the battery. Discard the
controller card as instructed by local regulations for lithium
batteries.
CAUTION:
Do not attempt to use the handle on the module to lift the entire
device (module and enclosure) as a unit. First remove the module;
then, use two hands to lift the enclosure.
Attention Notice
An attention notice indicates the possibility of damage to a program, device, or
system (server), or to data. An exclamation point symbol may accompany an
attention notice, but is not required. Sample attention notices follow:
Attention: If you use a power screwdriver to perform this
procedure it could destroy the tape.
Attention: Do not operate the Ultrium Tape Drive in a poor air quality
environment.
Laser Safety and Compliance
These products contain components that comply with performance standards that
are set by the U.S. Food and Drug Administration (Part 21CFR, 1040.10/11). This
means that these products belong to a class of laser products that do not emit
hazardous laser radiation. This classification was accomplished by providing the
necessary protective housing and scanning safeguards to ensure that laser
radiation is inaccessible during operation or is within Class I limits. External safety
agencies have reviewed these products and have obtained approvals to the latest
standards as they apply to this product type.
vi IBM Ultrium Internal Tape Drive
|
|
Summary of Changes
This section summarizes the changes that are contained in each edition of this
book.
Second Edition
This edition includes information about attaching the Ultrium Tape Drive Model
T200F, which features a Fibre Channel interface. Fibre Channel technology
increases the maximum server-to-tape-drive distance by using fiber optic cables. In
addition, Storage Area Network (SAN) components greatly extend the maximum
distance and the Fibre Channel topologies.
Third Edition
This edition removes references to the StorageSmart
™
by IBM brand and adds
clarifications to sections of text.
vii
|
|
|
|
|
|
|
|
|
viii IBM Ultrium Internal Tape Drive
Indice
Altri manuali Tandberg Data Magazzinaggio
Tandberg Data
Tandberg Data STORAGE CAB4000 - Manuale utente
Tandberg Data
Tandberg Data SDLT 600 Manuale utente
Tandberg Data
Tandberg Data Storage Library T24 Manuale utente
Tandberg Data
Tandberg Data DLT7000 Manuale utente
Tandberg Data
Tandberg Data StorageLibrary LTO-3 SCSI Manuale utente
Tandberg Data
Tandberg Data STORAGELIBRARY REV2 ONLINE - QUICK Manuale utente
Tandberg Data
Tandberg Data RDX QuikStor Manuale utente
Tandberg Data
Tandberg Data StorageLibrary T40 T40 Manuale utente
Tandberg Data
Tandberg Data RDX QuikStation 8 Manuale utente
Tandberg Data
Tandberg Data DAT320 Manuale utente
Tandberg Data
Tandberg Data RDX QuikStor Manuale utente
Tandberg Data
Tandberg Data StorageLibrary LTO-4 SCSI Manuale utente
Tandberg Data
Tandberg Data RDX QuikStor Manuale utente
Tandberg Data
Tandberg Data RDX QuikStation Manuale utente
Tandberg Data
Tandberg Data DLT-V4 Manuale del proprietario
Tandberg Data
Tandberg Data SDLT320 - Manuale utente
Tandberg Data
Tandberg Data SLR7 Manuale utente
Tandberg Data
Tandberg Data REPLACE TAPE DRIVE IN T24 OR T48 Manuale utente
Tandberg Data
Tandberg Data StorageLoader DLT VS160 Manuale utente
Tandberg Data
Tandberg Data REPLACE TAPE DRIVE IN STORAGELOADER VXA... Manuale utente
