OUT1 ON/OFF
R1. OFF
R2. OFF
R3. OFF
R4. ON
X1
START OR OPEN OR
DEAD-MAN OPEN
R1. ON
R2. OFF
R3. OFF
R4. OFF
X4
STOP
R1. OFF
R2. ON
R3. OFF
R4. OFF
X3
START OR FAST CLOSURE OR
CLOSE OR DEAD-MAN CLOSURE
R1. OFF
R2. OFF
R3. ON
R4. OFF
X2
RC1
RC2
ON
R1. OFF
R2. OFF
R3. OFF
R4. ON
X4
RC1
RC2
ON
R1. OFF
R2. OFF
R3. ON
R4. OFF
X3
R1. OFF
R2. ON
R3. OFF
R4. OFF
X2
R1. ON
R2. OFF
R3. OFF
R4. OFF
X1
STOP OUT1 ON/OFF
DEAD-MAN OPEN: OPENS UNTIL THE COMMAND IS ENABLED. The dead-man command takes precedence over stop and photocells securies.
DEAD-MAN CLOSURE: CLOSES UNTIL THE COMMAND IS ENABLED. The dead-man command takes precedence over stop and photocells securies.
DISABLE NOT WIRED N.C. INPUTS: DISABLE ALL NOT WIRED N.C. INPUTS. IF ANY N.C. INPUT IS THEREAFTER WIRED THE CONTROL UNIT WILL
AUTOMATICALLY ENABLE IT REGARDLESS OF THE DIP POSITION. DURING DEAD-MAN OPERATING LOGIC THE PHOTOCELLS TEST IS NOT EXECUTED
REGARDLESS OF THE DIP POSITION.
COMMUNITY MODE:
•During closing: the start commands invert the door movement.
•During opening: the start commands are ignored.
STEP-BYSTEP:
•During closing: the start commands stop the door movement.
•During opening: the start commands stop the door movement.
AUTOMATIC CLOSURE: ROLLING SHUTTER CLOSES AUTOMATICALLY AFTER THE THE PROGRAMMED AUTOMATIC CLOSURE TIME.
IF THE AUTOMATIC CLOSURE IS DISABLED THE ROLLING SHUTTER REMAINS OPENED AFTER THE OPENING PHASE.
FAST CLOSURE: DURING OPENING THE ROLLING SHUTTER CLOSES 3 SECONDS AFTER THE PHOTOCELLS ACTIVATION. THIS FUNCTION CAN BE
ACTIVATED ONCE EVERY WORKING CYCLE AND ONLY IF THE ROLLING SHUTTER MOVEMENT HAS NEVER BEEN STOPPED DURING THE OPENING
OR DURING THE TIME OF AUTOMATIC CLOSURE.
R1. ON
R2. ON
R3. ON
R4. ON
R1. OFF
R2. OFF
R3. OFF
R4. OFF
R1. OFF
R2. ON
R3. ON
R4. ON
R1. OFF
R2. OFF
R3. ON
R4. ON
R1. OFF
R2. OFF
R3. OFF
R4. ON
ERASE ALL REMOTES
TO ERASE ALL SAVED REMOTES PRESS AND HOLD THE REMOTE BUTTON ON THE BOARD FOR 6 SECONDS. LEDS R1, R2, R3, AND R4 WILL GO ON
STEADY THEN WILL GO OFF INDICATING CORRECT DELETION OF ALL REMOTES.
PRESS AND HOLD THE REMOTE
BUTTON ON THE BOARD FOR
ABOUT 6 SECONDS.
SUGGESTIONS
THE RADIO CASE CAN BE
INSTALLED IN COMBINATION
WITH THE FLASHING LAMP ONE UP.
THE RADIO
MODULE
HOUSED INSIDE
THE RADIO CASE
(RANPC5T).
TO INCREASE THE SIGNAL RANGE DISCONNECT THE RADIO MODULE FROM THE INTERNAL RECEIVER
POSITION AND WIRE IT ON THE TERMINAL BLOCK EXTERNAL RECEIVER POSITION. IF AVAILABLE, WE
SUGGEST YOU USE THE RADIO CASE (CODE RANPC5T).
1. RADIO MODULE CONNECTED IN
INTERNALRECEIVER POSITION
(DEFAULT CONFIGURATION).
2. DISCONNECT THE RADIO
MODULE FROMTHE INTERNAL
RECEIVER POSITION.
3. WIRE THE RADIO MODULE ON THE
TERMINAL BLOCK EXTERNAL RECEIVER
POSITION.
3. WIRE THE RADIO MODULE
ON THE TERMINAL
BLOCK EXTERNAL
RECEIVER
POSITION.
x x x
MEMORIZE A REMOTE
DELETE A REMOTE
START OR OPEN OR
DEAD-MAN OPEN START OR FAST CLOSURE OR
CLOSE OR DEAD-MAN CLOSURE
PRESS AND HOLD THE DESIRED BUTTON ON THE REMOTE, SIMULTANEOUSLY PRESS ONCE THE REMOTE BUTTON ON THE CONTROL BOARD TO
MEMORIZE THE START OR OPEN OR DEAD-MAN OPEN FUNCTIONS, PRESS TWICE THE REMOTE BUTTON ON THE BOARD TO MEMORIZE THE STOP
FUNCTION, PRESS THREE TIMES THE REMOTE BUTTON ON THE BOARD TO MEMORIZE THE START OR FAST CLOSURE OR DEAD-MAN CLOSURE
FUNCTIONS, PRESS FOUR TIMES THE REMOTE BUTTON ON THE BOARD TO MEMORIZE THE OUT1 ON/OFF FUNCTION. THE CORRESPONDING LED
(R1-START, R2-STOP, R3-PEDESTRIAN, OR R4-OUT1) WILL BE STEADY ON TO CONFIRM MEMORIZATION.
PRESS AND HOLD THE DESIRED BUTTON ON THE REMOTE, SIMULTANEOUSLY PRESS FOUR TIMES THE REMOTE BUTTON ON THE CONTROL BOARD
TO DELETE THE START OR OPEN OR DEAD-MAN OPEN FUNCTIONS, PRESS THREE TIMES THE REMOTE BUTTON ON THE BOARD TO DELETE THE
STOP FUNCTION, PRESS TWICE THE REMOTE BUTTON ON THE BOARD TO DELETE THE START OR FAST CLOSURE OR DEAD-MAN CLOSURE
FUNCTIONS, OR PRESS ONCE THE REMOTE BUTTON ON THE BOARD TO DELETE THE OUT1 ON/OFF FUNCTION.
FUNCTIONS DESCRIPTION / MODES
