Tektronix DPO2002B Manuale utente

DPO2000/B and MSO2000/B Series Oscilloscopes

Declassiﬁcation and Security

ZZZ

Instructions

www.tektronix.com

*P077010801*

077-0108-01

or suppliers, and are protected by national copyright laws and international treaty provisions.

Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication

supersedes that in all previously published material. Speciﬁcations and price change privileges reserved.

TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.

TekSecure is a trademark of Tektronix, Inc.

Contacting Tektronix

Tektronix, Inc.

14150 SW Karl Braun Drive

P.O. Box 50 0

Beaverton, OR 97077

USA

For product information, sales, service, and technical support:

In North America, call 1-800-833-9200.

Worldwide, visit www.tektronix.com to ﬁnd contacts in your area.

Table of Contents

Preface .............................................................................................................. iii

Clear and Sanitize Procedures...................... ............ .................................. ................. 1

Memory Devices............................................................................................... 1

Data Export Devices........................................................................................... 3

Built-In Security Features ......................................................................................... 4

When to Use TekSecure....................................................................................... 4

What TekSecure Does......................................................................................... 4

Disable the LAN Port and Clear LAN Ethernet Settings............................... .......... ......... 5

Disable the USB Device Port................................................................................. 6

Clear and Sanitize a Non-Functional Instrument. ............ .......................... ......................... 7

DPO2000/B and MSO2000/B Series Declassiﬁcation and Security Instructions i

Table of Contents

ii DPO2000/B and MSO2000/B Series Declassiﬁcation and Security Instructions

Preface

If you have data security concerns, this document helps you to sanitize or remove

memory devices from the DPO2000/B and MSO2000/B Series Digital Phosphor

and Mixed Signal Oscilloscopes.

The DPO2000/B and MSO2000/B series products have data storage (memory)

devices and data output devices (USB ports). These instructions tell you how

to clear or sanitize the memory devices, and also tell you how to declassify an

instrument that is not functioning.

Instrument code and calibration settings reside in nonvolatile ﬂash memory.

Instrument setups and reference waveforms may also be stored in ﬂashmemoryor

on USB drives connected to the instrument.

If you have any questions, contact the Tektronix Technical Support Center at

www.tektronix.com/support.

Products The following Tektronix products are covered by this document:

DPO2002B

DPO2004B

DPO2012/B

DPO2014/B

DPO2022B

DPO2024/B

MSO2002B

MSO2004B

MSO2012/B

MSO2014/B

MSO2022B

MSO2024/B

Related Documents The DPO2000 and MSO2000 Series Digital Phosphor and Mixed Signal

Oscilloscopes Service Manual, part number 071-2331-XX, is available on the

Tektronix Web site at www.tektronix.com/manuals.

DPO2000/B and MSO2000/B Series Declassiﬁcation and Security Instructions iii

Preface

Terms The following termsmaybeusedinthisdocument:

Clear. This removes data on media/memory before reusing it in a secured

area. All reusable memory is cleared to deny access to previously stored

information by standard means of access.

Erase. This is equivalent to clear.

Media storage/data export device. Any of several devices that can be used

to store or export data from the instrument, such as a USB port.

Nonvolatile memory. Data is retained when the instrument is powered off.

Power off. Some instruments have a “Standby” mode, in which power is

still supplied to the instrument. For the purpose of clearing data, putting the

instrument in Standby mode does not qualify as powering off. For these

products, you will need to either press a rear-panel OFF switch or remove the

power source from the instrument.

Remove. This is a physical means to clear the data by removing the memory

device from the instrument. Instructions are available in the product Service

Manual.

Sanitize. This eradicates the data from media/memory so that the data cannot

be recovered by other means or technology. This is typically used when the

device will be moved (temporarily or permanently) from a secured area to a

non-secured area.

Scrub. This is equivalent to sanitize.

User-modiﬁable. The user can write to the memory device during normal

instrument operation, using the instrument interface or remote control.

Volatile memory. Data is lost when the instrument is powered off.

iv DPO2000/B and MSO2000/B Series Declassiﬁcation and Security Instructions

Clear and Sanitize Procedures

Memory Devices

The following tables list the volatile and nonvolatile memory devices in the

standard instrument and listed options.

Table 1: Volatile Memory Devices for the DPO2000/B and MSO2000/B Series

Type and minimum size Function User modiﬁable

Data input

method Location To clear or sanitize

CMOS, SDRAM, 32MX16,

512MB DDR2, 1.8V, 333MHZ;

MT47H32M16CC-3, FBGA84

DDR memory: contains

the analog channel

waveform acquisition

data during operation

Only by the

processor system

N/A Acquisition board Remove power from the

instrument for at least

20 seconds

CMOS, SDRAM, 32MX16,

512MB DDR2, 1.8V, 333MHZ;

MT47H32M16CC-3, FBGA84

DDR memory: contains

the digital channel

waveform acquisition

data during operation

Only by the

processor system

N/A Acquisition board

(MSO2000/B Series

only)

Remove power from the

instrument for at least

20 seconds

CMOS, SDRAM, 64MX16,

1G DDR2, 1.8V, 333MHZ;

MT47H64M16BT-3, FBGA84

DDR memory: contains

the instrument code and

data during operation

Only by the

processor system

N/A Acquisition board Remove power from the

instrument for at least

20 seconds

CMOS, SDRAM, 32MX16,

512MB DDR2, 1.8V, 333MHZ;

MT47H32M16CC-3, FBGA84

DDR memory: contains

the instrument code and

data during operation

Only by the

processor system

N/A Acquisition board

(4-channel products

only)

Remove power from the

instrument for at least

20 seconds

DPO2000/B and MSO2000/B Series Declassiﬁcation and Security Instructions 1

Clear and Sanitize Procedures

Table 2: Nonvolatile Memory Devices for the DPO2000/B and MSO2000/B Series

Type and minimum size Function User modiﬁable

Data input

method Location To clear or sanitize

CMOS, FLASH; 16M X 8 OR

8M X 16, 128MBIT, 75NS, 3V;

PC28F128J3D-75, BGA64

FLASH: contains the

instrument ﬁrmware,

calibration constants,

reference waveforms,

and instrument setups

N/A N/A Acquisition board To clear: Not applicable

for calibration constants.

Use the TekSecure

featuretoerase

reference waveforms

and instrument setups.

Use the procedure to

disable the LAN Ethernet

and to clear information,

such as IP addresses.

(See page 5, Disable the

LAN Port and Clear LAN

Ethernet Settings.)

To sanitize: Remove

the acquisition board;

see the product service

manual for removal

instructions. Store the

removed board in a

secure area or destroy

it. Return the product

to Tektronix and a

new acquisition board

will be installed and

the instrument will be

repaired and adjusted as

necessary.

CMOS, CLOCK; SERIAL

REAL-TIME CLOCK,

CRYSTAL, 7 X 8 RAM, SPI,

3.3V; M41T93RMY, SO18.300

Real-time clock, with

battery backup

Only by the

processor system

N/A Acquisition board Not applicable; no user

data

CMOS, EEPROM; 128 X 8,

SERIAL; 24C01A, SOIC8

EEPROM: contains the

front end board serial

number and calibration

information

N/A N/A Front End Board Not applicable; no user

data

CMOS, MICROCONTROLLER;

8-BIT, 32K BYTES ON-CHIP

FLASH, MC9S08AW32CPUE,

LQFP64

Microcontroller with

FLASH: contains the

front panel processor

code and power status

for soft power switch

Only by the

processor system

N/A Front Panel Board Not applicable; no user

data

CMOS, EEPROM; 256 X 8,

SERIAL; 24C02, SO8.15

EEPROM: contains

the application module

ﬁrmware

N/A N/A DPO2000/B and

MSO2000/B application

module

Not applicable; no user

data

2 DPO2000/B and MSO2000/B Series Declassiﬁcation and Security Instructions

Clear and Sanitize Procedures

Data Export Devices

The following table lists the data export devices.

Table 3: Data Export Devices

Type and minimum size Function User modiﬁable

Data input

method Location To disable

USB host port Supports the removable

USB ﬂash drive; user

storage of reference

waveforms, screen

images, and instrument

setups

Yes Save USB host port on the

front of the instrument

Files can be deleted

or overwritten on the

instrument or a PC; the

USB ﬂash drive can be

removed and destroyed.

The USB host port

cannot be disabled.

USB device port Supports remote control

and data transfer to a

Yes Remote

control via

USBTMC

USB device port on the

rear of the instrument

Use the procedure to

disable the USB device

port. (See page 6,

Disable the USB Device

Port.)

DPO2000/B and MSO2000/B Series Declassiﬁcation and Security Instructions 3

Built-In Security Features

When to Use TekSecure

You can use the TekSecure function to erase setup and reference waveform data

stored in internal ﬂash memory.

The DPO2000/B and MSO2000/B series models have a USB host port on the

front panel. Any USB ﬂash devices can be removed, and stored or destroyed.

What TekSecure Does

The TekSecure function does the following:

Replaces all waveforms in all reference memories with null sample values

Replaces the current front-panel setup and all stored setups with the default

setup values

Calculates the checksums of all reference waveform memory and setup

memory locations to verify successful completion of waveform and setup

erasure

Displays a dialog indicating whether the secure erase was successful or

unsuccessful

NOTE. TekSecure does not erase or change factory calibration constants, user

protected data, or Ethernet settings.

To use TekSecure: 1. Push the front-panel Utility button.

2. Push the Utility Page lower-bezel button and use the Multipurpose a knob

to select Conﬁg.

3. Push the TekSecure Erase Memory lower-bezel button.

4.Push the OK Erase Setup & Ref Memory side-bezel button. Wait for the

“TekSecure operation complete” dialog box to display.

5. Push the Menu Off front-panel button to close the dialog box.

To reset the instrument

RAM:

1. Power off the instrument for at least 20 seconds.

2. Power on the instrument.

4 DPO2000/B and MSO2000/B Series Declassiﬁcation and Security Instructions

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Tektronix Apparecchiature di prova

Tektronix

Tektronix TBS2000B Series Manuale

Tektronix

Tektronix TDS5000B Series Manuale per l'uso e la cura

Tektronix

Tektronix DPO4104 Manuale utente

Tektronix

Tektronix TDS3012C Manuale utente

Tektronix

Tektronix TPS2014B Manuale utente

Tektronix

Tektronix DPO3000 Series Manuale utente

Tektronix

Tektronix DSA70000D Series Manuale utente

Tektronix

Tektronix 511A Manuale utente

Tektronix

Tektronix 2236 Manuale utente

Tektronix

Tektronix 2246 1Y Manuale utente

Tektronix

Tektronix P3010 Manuale utente

Tektronix

Tektronix P6248 Manuale utente

Tektronix

Tektronix 7934 Manuale utente

Tektronix

Tektronix TDS3000 Series Manuale utente

Tektronix

Tektronix CA PLUG-IN Manuale utente

Tektronix

Tektronix MDO3000 Series Manuale utente

Tektronix

Tektronix 2445B Manuale utente

Tektronix

Tektronix DPO70000C/DX Manuale utente

Tektronix

Tektronix TDS200 Series Manuale operativo e di manutenzione

Tektronix

Tektronix 2235 Manuale utente

Tektronix

Tektronix 7613 Manuale utente

Tektronix

Tektronix LE160 Manuale utente

Tektronix

Tektronix TDS 700A Manuale utente

Tektronix

Tektronix 7T11A Manuale utente

Manuali Apparecchiature di prova popolari di altre marche

SMART

SMART KANAAD SBT XTREME 3G Series Manuale utente

Agilent Technologies

Agilent Technologies BERT Serial Manuale utente

Agilent Technologies

Agilent Technologies N3280A Manuale utente

Vernier

Vernier Go Direct Voltage Manuale utente

Lifeloc

Lifeloc R.A.D.A.R. Manuale utente

Fluke

Fluke T5-600 Istruzioni per l'uso e l'installazione

Mercury

Mercury TSL01 Manuale utente

MAHA

MAHA MBT Series Manuale utente

Fuji Electric

Fuji Electric P-61 Manuale utente

ETC

ETC SealerAtor Manuale utente

Skyfine

Skyfine ETHYWAY V2 Manuale utente

Appion

Appion G5 Twin Manuale utente

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuale utente

BW Technologies

BW Technologies MicroDock II Manuale utente

Sun Nuclear

Sun Nuclear 1027 Manuale utente

Biomark

Biomark HPR LITE READER Manuale utente

Hioki

Hioki 3169-20 Manuale utente

Ashcroft

Ashcroft ATE-100 Manuale utente