Teledyne Lecroy PP066 Manuale utente

Operator’s Manual

PP02

Pass

ive Probe

700 Chestnut Ridge Road

Chestnut Ridge, NY, 10977-6499

Tel: (845) 425-2000, Fax: (845) 578 5985

teledynelecroy.com

PP022 Passive Probe Instruction Manual

Unauthorized duplication of Teledyne LeCroy documentation materials other than for internal

sales and distribution purposes is strictly prohibited. However, clients are encouraged to

duplicate and distribute Teledyne LeCroy documentation for internal educational purposes.

Teledyne LeCroy is a registered trademark of Teledyne LeCroy, Inc. Other product or brand

names are trademarks or requested trademarks of their respective holders. Information in this

publication supersedes all earlier versions. Specifications subject to change without notice.

This electronic product is subject to disposal and recycling regulations

that vary by country and region. Many countries prohibit the disposal of

waste electronic equipment in standard waste receptacles. For more

information about proper disposal and recycling of your Teledyne LeCroy

product, visit teledynelecroy.com/recycle.

925924-00

May, 2015

Operator’s Manual

Terms and Symbols

The following symbols appear on the product or in its documentation:

DANGER

High Voltage

WARNING

Refer to Manual. Condition or practice

could result in injury or loss of life.

DOUBLE INSULATION

PROTECTIVE (EARTH) TERMINAL

Introduction

The Teledyne LeCroy PP022 is a passive high impedance voltage

oscilloscope probe designed and calibrated for use with general purpose

oscilloscopes having an input impedance of 1 MΩ and can be compensated

for use with instruments having an input capacitance between 10 to 20 pF.

It is compatible with oscilloscopes that automatically detect probe

attenuation and adjust their readout accordingly.

PP022 Passive Probe

Specifications

Model Attn.

Input

Imped.

B/W

Rise

Time

Length

Compensation

Range

R (MΩ) C (pF) (MHz) (ps) (m) (pF)

PP022

10x

500

700

1.3

10 - 20

Attenuation Ratio.....................10:1 ± 1%

Max. Input Voltage...................Measurement Category I 1: 500 Vrms

1500 V transient overvoltage

(see voltage derating curve on p. 3)

Measurement Category II 2: 400 Vrms

Pollution Degree ......................Pollution Degree 2 3

Operating Temperature ..........0° C to +50° C

Humidity ....................................5% to 95% RH (10° C to 30° C)

5% to 75% RH (30° C to 40° C)

5% to 50% RH (above 40° C)

RH not controlled below 10° C

Operating Altitude....................3000 meters maximum

To reduce risk of fire or electric shock, do not exceed the

voltage or category ratings of the probe.

Definitions (per EN 61010-031)

1) Measurement Category I (CAT I)refers to measurements performed on circuits not directly

connected to mains.

2) Measurement Category II (CAT II) refers to measurements performed on circuits directly

connected to the low-voltage installation.

3) Pollution Degree 2 refers to an operating environment where normally only dry, non-conductive

pollution occurs. Temporary conductivity caused by condensation must be expected.

Operator’s Manual

PP022 Input Impedance Profile

Voltage vs. Frequency Derating Curve

PP022 Passive Probe

EC Declaration of Conformity

The probe is marked with this symbol to show compliance was

demonstrated to the specifications listed in the Official Journal of

the European Communities: Low Voltage Directive 2006/95/EC:

EN 61010-031/A1:2008 Safety requirements for electrical equipment for

measurement, control and laboratory use – Part 031: Safety requirements

for handheld probe assemblies for electrical measurement and test.

EU RoHS Compliance

The probe and its accessories conform to the 2011/65/EU RoHS2 Directive,

as they have been classified as Industrial Monitoring and Control

Equipment (per Article 3, Paragraph 24) and are exempt from RoHS

compliance until 22 July 2017 (per Article 4, Paragraph 3).

General Safety Information

Observe generally accepted safety procedures in addition to those

listed here to avoid personal injury or damage to equipment. The

overall safety of any system incorporating this accessory is the

responsibility of the assembler of the system.

Connect only to grounded instruments. Use only with compatible Teledyne

LeCroy oscilloscopes that have their BNC input connected to an earth

ground. Do not connect the probe reference lead to any point which is at a

potential other than earth ground.

Connect and disconnect properly. Connect probe to the oscilloscope before

connecting it to the test circuit. Disconnect the probe input and reference

lead from the test circuit before disconnecting from the oscilloscope. Do

not connect or disconnect probes while they are connected to a voltage

source.

Operator’s Manual

Do not overload. Do not apply any potential to the probe leads that exceeds

the maximum rating of the probe. Always comply with the Voltage vs.

Frequency Derating Curve.

Observe all terminal ratings. Observe all markings on the oscilloscope

before connecting. Consult the oscilloscope product manual for further

ratings information.

Do not remove probe casing. Touching exposed connections may result in

electric shock.

Use indoors only within operational environment listed. Do not use in wet or

explosive atmospheres. Keep product surfaces clean and dry.

Handle with care. Probe tips are extremely sharp and may puncture skin or

cause other bodily injury if not handled properly.

Keep fingers behind the finger guard of probe body and accessories.

Do not operate with suspected failures. Before each use, inspect the probe

and accessories for any potential damage such as tears or other defects in

the probe body, cable jacket, accessories, etc. If any part is damaged, cease

operation immediately and sequester the probe from inadvertent use.

Cleaning

•Clean only the exterior of the probe, cables, and accessories. Use a

soft cotton cloth moistened with a mild detergent and water solution.

Do not allow any portion of the probe to be submerged at any time.

•Dry the probe and accessory thoroughly before attempting to make

any voltage measurement.

•Do not subject the probe to solvents or solvent fumes as these can

cause deterioration of the probe body, cables, and accessories.

PP022 Passive Probe

Probe Compensation

Proper compensation of the probe is required to assure amplitude accuracy

of the waveform being measured by matching the probe to the

oscilloscope’s input capacitance. Compensation should be adjusted

whenever the probe is connected to or transferred between oscilloscopes.

Low Frequency

1. Apply a 1 kHz square wave to the probe or connect to the

oscilloscope’s calibrator output.

2. Adjust the single LF trimmer located on the PP022 BNC Box until you

achieve a flat-topped square wave (see figure below):

High Frequency

1. Apply a 1 MHz square wave to the probe (< 0.7 ns rise-time).

2. Remove the plastic caps from the two, high-frequency trimmers on

the PP022 BNC Compensation Box.

3. Adjust HF2 then HF1 until you achieve a flat-topped square wave (see

figure below).

Operator’s Manual

Over-compensated, correct, and under-compensated waveforms

Probe Accessories

Probe Tips

Both the rigid probe tip and the spring tip can be screwed on to the probe

body by hand.

Be sure not to overtighten the tips to avoid damaging

the threads.

Ground Accessories

The ground lead and the short collar are attached to the probe at the time

of shipping. To replace the ground lead with the swivel lead adapter,

unscrew the short collar from the probe and remove the ground lead.

Replace the short collar to hold the swivel lead adapter in place.

Alternatively, the long collar can be pushed onto the probe body and used in

conjunction with the ground spring, BNC adapter or PCB adapter.

Service

Refer all service to qualified personnel.

For the most complete and up-to-date list of sales and service centers by

country, visit teledynelecroy.com/support/contact.

PP022 Passive Probe

Replaceable Parts

Item

Part Number

Description

QTY

PK5-2.5MM-101

Ground Lead with Alligator Clip

PK5-2.5MM-102

Rigid Probe Tip (1 installed standard)

PK5-2.5MM-103

Short Collar (installed standard)

PK5-2.5MM-104

Sprung Hook

PK5-PK6-001

Trimmer Tool

PK5-2.5MM-105

Long Collar

PK5-2.5MM-106

IC Tip Insulators (Black, Brown, Blue, Green, Gray)

PK5-2.5MM-107

Tip Insulator 2.5mm

PK5-2.5MM-108

Probe Tip Cover

PK5-2.5MM-109

BNC Adapter 2.5mm

PK5-2.5MM-110

Swivel Ground Lead

PK5-2.5MM-111

Swivel Ground Lead Adapter

PK5-2.5MM-112

Ground Spring

PK5-2.5MM-113

PCB Adapter

PK5-2.5MM-114

Spring Tip

PK5-PK6-002

Color Coding Rings (2 ea. yellow, red, green, blue)

Standard Accessory Replacement Kit part number is PKIT5-2.5MM-101.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Teledyne Lecroy Apparecchiature di prova

Teledyne Lecroy

Teledyne Lecroy MS-500 Manuale utente

Teledyne Lecroy

Teledyne Lecroy WaveSurfer 3024Z Manuale utente

Teledyne Lecroy

Teledyne Lecroy MS-500 Manuale utente

Teledyne Lecroy

Teledyne Lecroy HDO4000 Manuale utente

Teledyne Lecroy

Teledyne Lecroy WaveRunner/MDA 8000HD Series Manuale utente

Teledyne Lecroy

Teledyne Lecroy HDO4104A Manuale utente

Teledyne Lecroy

Teledyne Lecroy HDO9000 Manuale utente

Teledyne Lecroy

Teledyne Lecroy WaveRunner/MDA 8000HD Series Manuale utente

Teledyne Lecroy

Teledyne Lecroy T3DSO3000 Manuale utente

Teledyne Lecroy

Teledyne Lecroy Summit Gen4 Test Platform Manuale utente

Teledyne Lecroy

Teledyne Lecroy WaveSurfer 4034HD Manuale utente

Teledyne Lecroy

Teledyne Lecroy RP2060 Manuale utente

Teledyne Lecroy

Teledyne Lecroy FrontLine Harmony Manuale utente

Teledyne Lecroy

Teledyne Lecroy AP033 Manuale utente

Teledyne Lecroy

Teledyne Lecroy HDO4024A-MS Manuale utente

Teledyne Lecroy

Teledyne Lecroy WaveSurfer 3000z Manuale utente

Teledyne Lecroy

Teledyne Lecroy WaveSurfer 3000z Manuale utente

Teledyne Lecroy

Teledyne Lecroy Everywhereyoulook HDO6000B Manuale utente

Teledyne Lecroy

Teledyne Lecroy HDO4000 Manuale utente

Teledyne Lecroy

Teledyne Lecroy WavePro HD series Manuale utente

Teledyne Lecroy

Teledyne Lecroy WaveSurfer 3000 Manuale utente

Teledyne Lecroy

Teledyne Lecroy HDO4032 Manuale utente

Teledyne Lecroy

Teledyne Lecroy frontline TLF 3000 Manuale utente

Teledyne Lecroy

Teledyne Lecroy WaveSurfer 510 Manuale utente

Manuali Apparecchiature di prova popolari di altre marche

SMART

SMART KANAAD SBT XTREME 3G Series Manuale utente

Agilent Technologies

Agilent Technologies BERT Serial Manuale utente

Agilent Technologies

Agilent Technologies N3280A Manuale utente

Vernier

Vernier Go Direct Voltage Manuale utente

Lifeloc

Lifeloc R.A.D.A.R. Manuale utente

Fluke

Fluke T5-600 Istruzioni per l'uso e l'installazione

Mercury

Mercury TSL01 Manuale utente

MAHA

MAHA MBT Series Manuale utente

Fuji Electric

Fuji Electric P-61 Manuale utente

ETC

ETC SealerAtor Manuale utente

Skyfine

Skyfine ETHYWAY V2 Manuale utente

Appion

Appion G5 Twin Manuale utente

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuale utente

BW Technologies

BW Technologies MicroDock II Manuale utente

Sun Nuclear

Sun Nuclear 1027 Manuale utente

Biomark

Biomark HPR LITE READER Manuale utente

Hioki

Hioki 3169-20 Manuale utente

Ashcroft

Ashcroft ATE-100 Manuale utente