Tellabs ONT180C Manuale utente
Copyright © 2021 Tellabs®All Rights Reserved
ONT180C Installation and Turnup Guide
ONT180C Installation and Turnup Guide
Page 2 of 38
Tellabs®Information
Copyright
Copyright © 2021 Tellabs Enterprise, Inc. All rights reserved.
The information in this publication is proprietary to Tellabs Enterprise, Inc.
No part of this publication may be used, disclosed, reproduced, adapted, translated, stored in a
retrieval system, or transmitted in any form or by any means, electronic or mechanical, for any
purpose, without the written permission of Tellabs Enterprise, Inc. Although every precaution
has been taken in the preparation of this publication, Tellabs Enterprise, Inc. assumes no (i)
responsibility for errors or omissions contained herein or (ii) liability for any damages resulting
from the use of information contained herein. Information in this publication is subject to change
without notice.
Trademarks
The following trademarks and service marks are owned by Tellabs Operations, Inc. or its
affiliates in the United States and/or other countries: TELLABS®, TELLABS and Tsymbol®,
Tsymbol®.
Any other company or product names may be trademarks of their respective companies.
Proprietary
This document is the property of Tellabs Enterprise, Inc. and contains confidential and
proprietary information owned by Tellabs Enterprise, Inc. Any copying, use, or disclosure of the
contents of this document, without the written permission of Tellabs Enterprise, Inc., is strictly
prohibited.
ONT180C Installation and Turnup Guide
Page 3 of 38
Table of Contents
Tellabs® Informaon................................................................................................................2
Copyright..........................................................................................................................................2
Trademarks...................................................................................................................................... 2
Proprietary....................................................................................................................................... 2
1. Tellabs® ONT180C Installaon and Turn Up Guide................................................................4
1.1. Descripon................................................................................................................................ 6
1.2. Site Preparaon....................................................................................................................... 13
1.3. Safety Precauons................................................................................................................... 17
1.4. Installaon...............................................................................................................................19
1.5. Contact Us............................................................................................................................... 33
1.6. Add to Panorama EMS............................................................................................................. 35
ONT180C Installation and Turnup Guide
Page 4 of 38
1. Tellabs® ONT180C Installation and Turn Up Guide
Document Revisions
Revision
Date
Notes
Revision A
May 27, 2021
·Formal Release of Document
Related Documentation
N/A
Contents
·Description
·Site Preparation
·Safety Precautions
·Installation
·Contact Us
·Add to Panorama EMS
Introduction
This guide describes the Tellabs ONT180C optical network terminal (ONT), its features,
status indicators, installation.
The ONT180C is part of the Tellabs 100 series of ONTs for passive optical networks
(PON). It is a compact desktop unit that can sit on a desk, mounted to any number of
surfaces using a wall mountbracket (optional).
When connected to a Tellabs 1100-series optical line terminal (OLT — 1150/1150E,
1134, or 1131) through a single fiber optic cable, the ONT provides high-performance
ONT180C Installation and Turnup Guide
Page 5 of 38
enterprise features, combined with cost, energy, and space savings, all within the
Tellabs exclusive high-security All Secure™ PON.
Intended Audience
This document is intended for technicians responsible for:
·Preparing the install location
·Unpacking and installing the ONT and any accessories
·Connecting the ONT to power and the PON network
·Connecting services to the ONT
ONT180C Installation and Turnup Guide
Page 6 of 38
1.1. Description
·LED Behavior
·ONT180C Manual Controls and Switches
·ONT180C Specifications
The ONT180C supports the following features.
General Features
·Single fiber GPON interface with 1.25Gbps upstream and 2.5Gbps downstream
data rates
·802.3bt 4PPoE Type 3 PSE capable of Class 1 through 6 , supplying up to 60W
on a single port (51W at the PD) for powering downstream Powered Devices
(PD), with 140 W total PoEoutput for the ONT when powered by the AC adapter
·Fully ITU-T G.984-compliant framing
·Flexible mapping between GEM ports and T-CONTs
·Supports single and multiple T-CONT and GEM ports per device
·Activation with automatic discovered Serial Number
·AES-128 Decryption with key generation and rapid churning
ONT180C Installation and Turnup Guide
Page 7 of 38
·Forward Error Correction(FEC)
·IP DSCP to 802.1pbit mapping
·Rich set of LED indications for alarming and maintenance
·Supports eight (8) VLANs per port, 25 VLANs per port when VLAN trunk is used,
up to 125 VLANs per ONT.
Ethernet Features
·Eight (8) 10/100/1000 Base-T Ethernet ports
·Auto-sensing MDI/MDIX or manual configuration
·802.1Q VLANs
·Ethernet ports support auto negotiation or manual configuration
·IP ToS/DSCP to 802.1p mapping
·QoS based on VLAN-ID, 802.1p bit, ToS/DSCP
·Marking/remarking of 802.1p
·IGMP v2/v3snooping
·Up to 255 MAC addresses per port
·IPv6-capable for enterprise services
·Upstream ACL rate limiting
·IEEE 802.3 az Energy-efficient Ethernet
·IEEE 802.1x Port-Based authentication
·IEEE802.3af PoE, high power IEEE802at PoE+ and IEEE802.3bt, including up to
Class 5 negotiations
·Support for 60W UPoE for devices supporting Cisco UPoE
·Link Layer Data Protocol(LLDP) for auto-provisioning and inventory, and LLDP-
MED for PoE power management
·Advanced data features such as VLAN tag manipulation, VLAN trunking,
classification, and filtering
ONT180C Installation and Turnup Guide
Page 8 of 38
·Network Access Control (NAC) with Dynamic VLAN and Guest VLAN
·Upstream broadcast rate limiting and filtering for security control
·Dante and Cobranet Support
Security
Tellabs has implemented unique advanced security features to protect enterprise
networks. The ONT180C supports security across the optical distribution network and
end-to-end over the OLAN system; such as encryption of traffic on the PON using the
Advanced Encryption Standard AES-128 and Access Control Lists (ACL) at Layer 2
through 4 levels.
The ONT provides for advanced dynamic assignment of services to a port via the use of
Network Access Control (NAC) with fall back to a Guest VLAN. The ONTsupports
IEEE 802.1x port-based authentication and MAB. This prevents unauthorized access to
ports, and offers RADIUS authentication for users and distribution of policy to end users
based on their login.
ONT180C Connectors
The back edge of the ONT180C has 11 connectors;
·UPS– Uninterruptible Power Supply (UPS) AC adapter input. This is a special
connector that matches the DC power output cable from the adapter and the
optional Battery Backup Unit (BBU) accessory (not currently available). This
connector is also used for the 150W high power AC adapter.
·DC 54V DC– power input. This is a special power connector that mates with a
Phoenix-type pluggable terminal connector (5.08 mm pitch 2P), allowing remote
ONT180C Installation and Turnup Guide
Page 9 of 38
bulk DC power to be used. (Remote bulk DC power is limited to 100 VA by NEMA
class 2 code.)
·GE1– GE8– 1000BT Gigabit Ethernet ports (eight) supporting Power over
Ethernet (PoE) devices. These are standard RJ45 Ethernet port jacks.
·Optical Connector (behind laser cover). The ONT to the Optical Line Terminal
(OLT) upstream over a fiber-optic cable. It is a standard SC/APC-type connector
for Single-Mode Fiber (SMF) cable. The connector is protected by a small plastic
cover located at the right-hand corner of the back panel (when viewed from the
rear).
ONT180C Indicators
The top of the ONT180C has 10 LED indicators near the front edge:
·Power– shows status of the DC power input
·PON– shows status of the Passive Optical Network (PON)
·GE1 – GE8– shows status of the eight Gigabit Ethernet ports
LED Behavior
LED
Indications
Comments
Power
Green
Input power is good to the ONT
Dark
Power is off to the ONT or power unit has failed
PON
Red
The PON is currently down, ONT is not receiving a signal from the OLT
ONT180C Installation and Turnup Guide
Page 10 of 38
Green
Blink Fast
The PON is up and ONT is attempting to register on the PON. If Auto Configuration is
not enabled, use Unknown ONT option on the Panorama PON to register ONT.
Green
Blink Slow
The board is performing a software download.
Green
The PON is up and operating normally.
Dark
The ONT is booting
GE1-
GE8
Green
•Link(Up)•PoE(No PD Detected)•Data(No data detected)
Green
Blink
•Link(Up)•PoE(No PD Detected)•Data(Data detected)
Amber
•Link(Up)•PoE(Powering PD)•Data(No Data Detected)
Amber
Blink
•Link(Up)•PoE(Powering PD)•Data(Data Detected)
Dark
The Ethernet Port is disabled or link is not detected
ONT180C Manual Controls and Switches
The ONT180C has only one user-operable control:
·Reset – This pushbutton resets the ONT
The Reset pushbutton is accessible through a small hole on the right-hand side of the
unit (when viewed from the front).
ONT180C Specifications
ONT180C specifications are listed in Table B.
Indice
Altri manuali Tellabs Hardware di rete
Tellabs
Tellabs 6047 Manuale utente
Tellabs
Tellabs 8820 MSR Guida utente
Tellabs
Tellabs FlexSym OLT-mini Manuale utente
Tellabs
Tellabs 100 Series Manuale utente
Tellabs
Tellabs FlexSym ONT205 Manuale utente
Tellabs
Tellabs FlexSym OLT6 Manuale utente
Tellabs
Tellabs 251 Manuale utente
Tellabs
Tellabs 7100 Istruzioni operative e di manutenzione
Tellabs
Tellabs 263DC Manuale utente
Manuali Hardware di rete popolari di altre marche
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manuale utente
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manuale utente
Yudor
Yudor YDS-16 Manuale utente
D-Link
D-Link ShareCenter DNS-320L Manuale utente
Samsung
Samsung ES1642dc Istruzioni per l’uso
Honeywell Home
Honeywell Home LTEM-PV Istruzioni per il montaggio
