Tesla TSL-TRV-GS361A Manuale utente
TSL-TRV-GS361A
Tesla Smart TRV Style
User Manual
EN
SK
DE
PL
CZ
2
1 Overview
Radiator Thermostat (GS361-H04), using dry battery
power supply, without wiring, easy installation, for the
temperature control of warm water radiator, provide
comfortable temperature, reduce energy waste, save
the cost of heating users. This product has a built-in
Zigbee® (Tuya) wireless communication module with
low power and LCD display screen. It can be used
individually and can be added to the Tesla Smart APP
to make it an intelligent thermostat.
After joining the Tesla Smart system, you can select
the mode, set the temperature, set the child lock
and set the window detection function in APP. Any
operation at the device side will also be synchronized
to APP, such as setting temperature manually.
2 Features
•3 mode settings—Automatic mode (For future),
Manual mode and Anti- freezing mode.
•Temperature setting range 5~30°C(For Automatic
mode and Manual mode) or 5~15°C(For Anti-freezing
mode).
•With LCD display screen and big characters, easy
to see.
•Battery life depends on networking or not. (1~2 years
for networking, 2~3 years for using alone)
•zigbee® wireless communication protocol, safe,
reliable and convenient.
•Easy to join TeslaSmart intelligent system.
3
3 Illustration
1 LCD display screen
2 Knob / Press: Setting mode / Rotate: Adjusting
temperature
3 Interface nut
1 Fault
2 Low battery
3 Temperature you set
4 Window detection
5 Automatic mode
6 Manual mode
7 Installation mode
8 Networking
9 Child lock
4
4 Installation Instruction
4.1 Put in battery
1) Turn the outer case towards the arrow with right
hand and pull out.
2) Refer to the polarity direction of the battery
compartment, put in 2 AA alkaline batteries.
Note that cannot use rechargeable batteries.
3) After putting into the batteries, the current tempera-
ture and symbol will be displayed.
4) Load the outer case and turn it towards the opposite
direction with right hand to complete the installation
of batteries.
4.2 Start to use
You can use your thermostat in only a few steps.
5
1) Press the knob and hold on for 3 seconds before the
product be installed on the valve.
2) Until the appears and the symbol
flickers, there will be slight vibration at the same time.
3) Align the thermostat interface nuts to the radiator
valve. Then push forward slightly and turn the interface
nuts clockwise until tightening. The maximum torque
is 5N·m.
4) Press the knob again and appears.
5) After about 10 seconds, the symbol
disappears and the current temperature is displayed.
The installation is finished.
In order to minimize the influence of the radiator‘s
own heat on the thermostat, it is recommended to
install as follows.
6
4.3
Automatic detection
•When the thermostat is installed, the equipment
will be adjusted automatically according to the
heating system. During this process, you may find
that the thermostat is slow response or self-heating /
self-cooling. This is normal and is a necessary part of
the adjustment process.
•Thethermostatwillclosetheradiatorvalveataspecific-
time,andthenopens it again to detect the exact ope-
ning position of the valve. The automatic detection
function can make use of heat as efficiently as possi-
ble and control the temperature more accurately.
•Ifnecessary,pleasereloadthebatteryandactivatethein-
stallationmodeand manually run the automatic
detection function.
Correct
7
4.4
About valve
5 Operation instruction
5.1 Select mode locally
In standby status, press the button to switch in three
modes: Automatic, Manual and Anti-freezing.
•Automatic mode (For future)
Automatic mode, the thermostat automatically swit-
ches to the required temperature, such as set at 21°C
when being home, set at 17°C when sleeping, and set
at 15 °C when being away home. The automatic mode
needs to connect to the gateway and needs network.
•Manual mode
Manual mode, this temperature you set will not
change because of the different situation mode. the
temperature can be set manually by adjusting the knob
and the temperature range is 5~30°C.
Installation diagram of valve A.
Installation diagram of valve B.
8
•Anti-freezing mode
Anti-freezing mode, while you leave home for a long
time, set the thermostat as an anti-freezing mode with
a range of 5~15°C. This mode is mainly designed to
protect water pipes from freezing at low temperatures.
5.2 Set temperature locally
Under the standby status, turn around the knob can
adjust the temperature after pressing the knob.
5.3 Set child lock locally
Long press the thermostat knob to turn on or close the
child lock function, as shown in the following figure.
When the child lock function enables, all operations
on the thermostat will be invalid to prevent children
from playing with the thermostat or misoperation
because of curiosity.
Note that setting child lock locally must be done after
installation.
9
1) Press the knob and hold on for more than 3 seconds.
2) A symbol appears to indicate that the child
lock has been enabled. Repeated operation 1 will
un-enable the child lock function.
5.4 Installation of Tesla Smart APP
Scan the QR code as below, get and install Tesla Smart
APP for IOS and Android system.
Tesla Smart APP
5.5 Set gateway of Tesla Smart
After installing Tesla Smart APP, it is necessary to
operate the network-setting of the Tesla Smart
ZigBee Hub.
1) Login the APP after registration
2) Click ‘Add Device’
3) Select ‘Tesla Smart ZigBee Hub’
4) Make sure the LED is always on and click to next
5) Wait and until next Interface appears
6) Finished
5.6 Add into Tesla Smart
In standby mode, the thermostat will enter the mat-
ching mode by pressing the knob three times quickly.
Matching process is limited to 2 minutes, cannot be
interrupted halfway and then automatically withdraw.
10
1) Click ‘Add sub device’
2) Find out ‘Thermostat’ and click it to match.
3) Click the knob 3 times quickly.
4) Wait and until next
5) Successfully Interface appears
6) Main page
5.7 Mode selection in APP
It supports to switch Automatic mode, Manual mode
and Anti-freezing mode in APP. Please refer to the
introduction of section 5.1 for the differences between
different modes.
5.8 Set temperature in APP
The temperature settings in different modes are sup-
ported in APP, and the operation can be accomplished
by dragging the adjusting ball simply.
(Drag the adjusting ball to set the temperature.)
Click or button to set one mode.
Altri manuali per TSL-TRV-GS361A
1
Indice
Lingue:
Manuali Unità di controllo popolari di altre marche
Festo
Festo Compact Performance CP-FB6-E Manuale elenco delle parti
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuale utente
JS Automation
JS Automation MPC3034A Manuale utente
JAUDT
JAUDT SW GII 6406 Series Guida rapida
Spektrum
Spektrum Air Module System Manuale utente
BOC Edwards
BOC Edwards Q Series Manuale utente
