Texas Instruments FPC401 Manuale utente
1
SNLU222B–December 2016–Revised September 2019
Submit Documentation Feedback Copyright © 2016–2019, Texas Instruments Incorporated
FPC401 and FPC402 Evaluation Module (EVM) User’s Guide
User's Guide
SNLU222B–December 2016–Revised September 2019
FPC401 and FPC402 Evaluation Module (EVM) User’s
Guide
The information and/or drawings set forth in this document and all rights in and to inventions disclosed
herein and patents which might be granted thereon disclosing or employing the materials, methods,
techniques, or apparatus described herein are the exclusive property of Texas Instruments. No disclosure
of information or drawings shall be made to any other person or organization without the prior consent of
Texas Instruments.
Contents
1 Hardware Description and Setup .......................................................................................... 2
1.1 Power Configuration................................................................................................ 2
1.2 Communication Protocol Configuration.......................................................................... 3
2 FPC401 EVM GUI Description and Setup................................................................................ 5
2.1 Installation ........................................................................................................... 6
2.2 Initializing Communication......................................................................................... 6
2.3 Local FPC Read and Write........................................................................................ 8
2.4 Remote Access on Downstream Modules....................................................................... 9
2.5 Input and Output Status and Configuration.................................................................... 10
2.6 Interrupt Configuration and Monitoring ......................................................................... 11
2.7 LED Configuration................................................................................................. 12
2.8 Prefetch Configuration............................................................................................ 13
2.9 Data-Driven Interrupt Configuration............................................................................. 14
2.10 Scheduled Write Configuration.................................................................................. 15
Trademarks
All trademarks are the property of their respective owners.
Hardware Description and Setup
www.ti.com
2SNLU222B–December 2016–Revised September 2019
Submit Documentation Feedback
Copyright © 2016–2019, Texas Instruments Incorporated
FPC401 and FPC402 Evaluation Module (EVM) User’s Guide
1 Hardware Description and Setup
The general procedure for setting up the FPC401 and FPC402 Evaluation Modules (EVM) is described in
the following sections.
Figure 1. FPC40xEVM – Top and Bottom
1.1 Power Configuration
Configure the power illustrated by Figure 2.
1. If the LDO is used to power the FPC, enable the LDO through header J8 and connect the LDO output
to VDD1 using header J4 (note that each header connection is rated for 1 A of current). Make sure
headers J7 and J13 are disconnected. The LDO has a maximum rated current of 1.5 A, so if the
cumulative QSFP/SFP module current draw is greater than that, the LDO may not be used.
2. If the LDO is not used and the FPC is powered through an external supply, configure the J8 header to
disable the LDO and connect VIN to VDD1 using header J7 (note that each header connection is rated
for 1 A of current). Make sure headers J4 and J13 are disconnected.
3. If USB power is used to power the FPC, ensure the LDO and VIN and disconnected from VDD1
(disconnect headers J4 and J7). Connect the 3.3 V of the MSP430 microcontroller to VDD1 through
header J13. Note that a typical computer USB port is only able to supply up to 100 mA which will be
enough to power the FPC and passive modules (that is, DAC); but it will not be enough to power active
SFP+ and QSFP+ modules which are plugged in.
4. To set VDD2 to 3.3 V, connect it to VDD1 through header J2. To operate at lower host-side supply
voltages (down to 1.8 V), connect an external supply to the header or test point loop (TP3).
5. The FPC401EVM and FPC402EVM includes a TPS2561 power switch which is used to selectively
enable and disable 3.3-V power to the SFP and QSFP ports. The FPC controls this power switch with
its GPIO pins. To supply power to ports 0 and 1 (QSFP+ ports and LEDs), configure the FPC GPIO0
high logic output to enable the power switch. Similarly, configure GPIO1 to high logic to enable power
for ports 2 and 3 (SFP+ ports and LEDs). Alternatively, supply 3.3 V externally through the test points
(TP4 and TP5). Note that the ground is shared with the board.
6. GPIO2 and GPIO3 are connected to the fault outputs of the power switch, and hence should be set as
inputs or left unconfigured.
www.ti.com
Hardware Description and Setup
3
SNLU222B–December 2016–Revised September 2019
Submit Documentation Feedback Copyright © 2016–2019, Texas Instruments Incorporated
FPC401 and FPC402 Evaluation Module (EVM) User’s Guide
Figure 2. Power Block Diagram – Configured for LDO Use
1.2 Communication Protocol Configuration
The following sections describe how to configure the FPC401EVM and FPC402EVM for I2C and SPI
protocols.
1.2.1 I2C Configuration
For I2C communication with the onboard MSP430, refer to Figure 3 and configure the board based on the
following procedure.
1. Leave the PRTCL_SEL pin disconnected (header J3).
2. Connect the MSP430 SCL and SDA to the FPC SCL and SDA through header J12. The SPI header
(J9) should be disconnected.
3. Connect the 2.7-kΩpullup resistors through header J1.
4. Connect the VDD2 pin to the VDD1 pin through header J2.
5. Connect the ADDR_N pin to GND through header J2 with the provided jumper wire.
For I2C communication with an external host controller, disconnect the MSP430 SDA and SCL. Connect
the FPC SDA and SCL pins to the SDA and SCL pins of the host controller. Only connect the onboard
pullup resistors if the host board does not have pullups.
To control multiple EVMs, connect all the SDA and SCL pins together. Only one board should have the
MSP430 and pullup resistors connected to these pins. The ADDR_N of the first device should be tied to
GND as shown in Figure 3 . Connect DONE_N pin of the first device to the ADDR_N of the second
device, and the DONE_N pin of that device to the following device in a daisy-chained fashion until all
ADDR_N pins are connected. Connect the final DONE_N pin to GND. See the data sheet for more details
on how I2C is configured.
Figure 3. I2C Configuration
Hardware Description and Setup
www.ti.com
4SNLU222B–December 2016–Revised September 2019
Submit Documentation Feedback
Copyright © 2016–2019, Texas Instruments Incorporated
FPC401 and FPC402 Evaluation Module (EVM) User’s Guide
1.2.2 SPI Configuration
For SPI communication with the onboard MSP430, refer to Figure 4 and configure the board based on the
following procedure.
1. Connect the PRTCL_SEL pin to GND through header J3.
2. Connect the MSP430 MISO, MOSI, SCK, and SS_N pins to the FPC MISO, MOSI, SCK, and SS_N
pins through header J9. The I2C header (J12) should be disconnected.
3. Connect the VDD2 pin to the VDD1 pin through header J2.
For SPI communication with an external host controller, disconnect the MSP430 MOSI, MISO, SCK, and
SS_N pins. Connect the FPC MOSI, MISO, SCK, and SS_N pins to the MOSI, MISO, SCK, and SS_N
pins of the host controller.
To control multiple EVMs with SPI, connect all the SCK and SS_N pins to a single MSP430 SCK and
SS_N pins. Daisy chain the MOSI and MISO pins so that the MOSI of the MSP430 connects to the MOSI
of the first device, the MISO of the first device connects to the MOSI of the second device, and so on, until
the final device's MISO connects to the MISO of the MSP430. See the data sheet for more details on how
SPI is configured.
Figure 4. SPI Configuration
www.ti.com
FPC401 EVM GUI Description and Setup
5
SNLU222B–December 2016–Revised September 2019
Submit Documentation Feedback Copyright © 2016–2019, Texas Instruments Incorporated
FPC401 and FPC402 Evaluation Module (EVM) User’s Guide
2 FPC401 EVM GUI Description and Setup
The FPC401 EVM GUI is used to program both FPC401EVM and FPC402EVM. The general procedure
for setting up the FPC401 GUI is described in the sections below.
Figure 5. FPC401 EVM GUI
FPC401 EVM GUI Description and Setup
www.ti.com
6SNLU222B–December 2016–Revised September 2019
Submit Documentation Feedback
Copyright © 2016–2019, Texas Instruments Incorporated
FPC401 and FPC402 Evaluation Module (EVM) User’s Guide
2.1 Installation
The FPC401 EVM GUI has two installers. The Setup_FPC401_EVM.exe installer does not contain the
National Instruments Run-Time Engine and requires web access to download the NI run-time engine if the
computer does not already have this installed. The Setup_FPC401_EVM_with_RTE.exe installer is a
larger file that contains the run-time engine and does not require web access. Select the appropriate
installer and follow the installer wizard to install the FPC401 EVM GUI.
2.2 Initializing Communication
To initialize communication with the FPC401EVM, first select the number of FPC401s under FPC Count
and the protocol (I2C or SPI), highlighted by Figure 6. Click OPEN LINK to establish communication with
the MSP430 through USB and initialize the device. In I2C mode, this will configure the MSP430 and
automatically configure the I2C addresses of all connected FPC401s so that each one has a unique
address. In SPI mode, this will configure the MSP430 and establish the length of the SPI message. Each
time the hardware configuration changes, the link must be reestablished. For example, connecting
additional FPC401s or changing the communication from I2C to SPI requires the link to be reestablished.
The TOGGLE LED button will toggle the LED (D7) for a visual indication that the USB communication is
working. The text in the bottom of the GUI should say CONNECTED and turn green after USB
communication is established. Note that this means that the computer is communication with the MSP430
but does not necessarily mean that communication is established with the FPC401.
The CLOSE LINK button will terminate USB communication.
Figure 6. Communication Control
www.ti.com
FPC401 EVM GUI Description and Setup
7
SNLU222B–December 2016–Revised September 2019
Submit Documentation Feedback Copyright © 2016–2019, Texas Instruments Incorporated
FPC401 and FPC402 Evaluation Module (EVM) User’s Guide
The top right section of the GUI highlighted by Figure 7 controls the FPC(s) being programmed by all
controls in this GUI. The Instance # selects which FPC is being controlled, starting at instance 0. The Port
#selects which port is being configured, where 0 is the port 0 of FPC instance 0, and 4 is port 0 of FPC
instance 1. The Broadcast switch will broadcast commands to all FPCs if set to 1. Note that if a command
that targets a port is broadcasted, not all ports will be modified. Instead, only ports that match the local
port of the selected instance are modified. For example, broadcasting a command that targets port 5 (local
port 1 of instance 1) will affect ports 1, 5, 9, 13, and so forth.
Figure 7. FPC Instance and Port Selection
FPC401 EVM GUI Description and Setup
www.ti.com
8SNLU222B–December 2016–Revised September 2019
Submit Documentation Feedback
Copyright © 2016–2019, Texas Instruments Incorporated
FPC401 and FPC402 Evaluation Module (EVM) User’s Guide
2.3 Local FPC Read and Write
To read and write to local FPC registers, select the Local Reads and Writes tab. Select the instance
number and register offset address to be read or written to. To write, select a value using the radio boxes
in the WRITE COMMAND section or type the desired hex value and click EXECUTE WRITE. To read,
click EXECUTE READ. The RESET FPC REGISTERS button will reset the instance's local FPC registers.
Note that performing a register reset in I2C mode will restore the default I2C address of the device and the
link must be closed and reopened to restore normal GUI operation.
Figure 8. FPC401 GUI – Local Reads and Writes
www.ti.com
FPC401 EVM GUI Description and Setup
9
SNLU222B–December 2016–Revised September 2019
Submit Documentation Feedback Copyright © 2016–2019, Texas Instruments Incorporated
FPC401 and FPC402 Evaluation Module (EVM) User’s Guide
2.4 Remote Access on Downstream Modules
To perform a remote access read or write on a downstream port, select the Downstream Reads and
Writes tab. Select the port number, downstream device I2C address, and register offset address. To write,
select a value using the radio boxes in the WRITE COMMAND section or type the desired hex value and
click EXECUTE WRITE. To read, click EXECUTE READ. The Set I2C Rate switch will toggle the I2C rate
of the downstream between 100 kHz (SFP) and 400 kHz (QSFP).
Figure 9. FPC401 GUI – Downstream Reads and Writes
FPC401 EVM GUI Description and Setup
www.ti.com
10 SNLU222B–December 2016–Revised September 2019
Submit Documentation Feedback
Copyright © 2016–2019, Texas Instruments Incorporated
FPC401 and FPC402 Evaluation Module (EVM) User’s Guide
2.5 Input and Output Status and Configuration
To control the input, output, and GPIO pins, select the I/O Status and Configuration tab. The Enable
Periodic Update button will update the indicator of each input, GPIO, and output periodically set by the
Update Period (ms) slider. This will also update the Port's Aggregated Interrupt Flag which determines if
any interrupt of the selected port has been triggered. To modify the state of the GPIOs, modify the GPIO
0/1/2/3 Set drop-down menus and click SET GPIOS. To modify the state of the outputs, modify the OUT
A/B Set drop-down menus and click SET OUTPUTS.
Figure 10. FPC401 GUI – Input, Output, GPIO Status, and Control
Altri manuali per FPC401
1
Questo manuale è adatto per i seguenti modelli
3
Indice
Altri manuali Texas Instruments Unità di controllo
Texas Instruments
Texas Instruments TPS23525EVM-815 Manuale utente
Texas Instruments
Texas Instruments PCM1808EVM Manuale utente
Texas Instruments
Texas Instruments AWR1642 Manuale utente
Texas Instruments
Texas Instruments ADS1202 Manuale utente
Texas Instruments
Texas Instruments DRV2625 Haptics BoosterPack Manuale utente
Texas Instruments
Texas Instruments DAC38RF8xEVM Series Manuale utente
Texas Instruments
Texas Instruments LMZ35003EVM-001 Manuale utente
Texas Instruments
Texas Instruments CC3000 Manuale utente
Texas Instruments
Texas Instruments TRF3705EVM Manuale utente
Texas Instruments
Texas Instruments THS1030/31EVM Manuale utente
Texas Instruments
Texas Instruments LP8864 Manuale utente
Texas Instruments
Texas Instruments TPS54232EVM-415 Manuale utente
Texas Instruments
Texas Instruments BQ25886 Manuale utente
Texas Instruments
Texas Instruments TLC5540 Manuale utente
Texas Instruments
Texas Instruments DAC5652AEVM Manuale utente
Texas Instruments
Texas Instruments TLC694 Series Manuale del prodotto
Texas Instruments
Texas Instruments XIO2001 Manuale utente
Texas Instruments
Texas Instruments TPS650380EVM-054 Manuale utente
Texas Instruments
Texas Instruments LM3643EVM Manuale utente
Texas Instruments
Texas Instruments TPS54362B EVM Manuale utente
Manuali Unità di controllo popolari di altre marche
Festo
Festo Compact Performance CP-FB6-E Manuale elenco delle parti
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuale utente
JS Automation
JS Automation MPC3034A Manuale utente
JAUDT
JAUDT SW GII 6406 Series Guida rapida
Spektrum
Spektrum Air Module System Manuale utente
BOC Edwards
BOC Edwards Q Series Manuale utente
