Texas Instruments DLP LightCrafter 160CP Manuale utente

EVM User's Guide: DLPCLCR160CPEVM

DLP® LightCrafter™ Display 160CP Evaluation Module

Description

The DLP® LightCrafter™ Display .16 nHD Evaluation

Module (EVM) is designed to enable microcontroller

(MCU) generated graphics display without the need

of a video processor, opening new possibilities

for affordable DLP free-form on-demand display

implementations in industrial and personal electronic

applications such as appliances, human machine

interface, robotics, and toys. This EVM features

DLP160CP chipset including DLPC3421, .16 nHD

(360x640) optical engine, and MSPM0G3507 MCU for

image generation out of the box.

Features

• Small form factor (66 mm x 56 mm)

• First DLP display EVM capable of displaying MCU

generated content

• Easily evaluate image display from Micro SD card

• MSPM0G MCU family compatible (JTAG, UART

supported)

www.ti.com Description

DLPU131 – NOVEMBER 2023

Submit Document Feedback

DLP® LightCrafter™ Display 160CP Evaluation Module 1

1 Evaluation Module Overview

1.1 Introduction

This user’s guide presents an overview of the DLP® LightCrafter™ Display 160CP evaluation module (EVM)

(DLPCLCR160CPEVM) and a general description of the main features and functions. The guide explains the

first steps to get started, and shows a detailed description of onboard LEDs, connectors, and overall EVM

assembly.

The EVM can be used by itself to display nHD (640x360) resolution graphics or images either generated by the

DLPC3421 display controller or the MSPM0G3507 MCU (microcontroller). Images can also be added from a

Micro-SD card through the MSPM0 MCU.

This guide provides the user with further information on how to successfully operate the EVM and get content

projected on the wall.

1.2 Kit Contents

The DLPDLCR160CPEVM is shipped as a fully assembled unit. The only component required to power up the

unit is a compatible power adapter (not included).

A 5 V power adapter with a 1 A minimum output and a USB-C connector is required.

1.3 DLPDLCR160CPEVM Subsystems

The DLP LightCrafter Display module consists of two subsystems:

•Formatter Board: includes the DLP chipset (DLPC3421 display controller and DLPA2005 PMIC/LED driver).

The MSPM0G3507 MCU, SSD1963 video interface driver, and Micro-SD card connector are also included.

•Light Engine: includes optics, RGB LEDs, and DLP160CP DMD displaying 640 × 360 pixels (nHD) on

screen.

The DLPDLCR160CPEVM is designed to operate at a maximum ambient temperature of 30°C. A block diagram

of the DLPDLCR160CPEVM is shown in Figure 1-1.

Figure 1-1. DLPDLCR160CPEVM Block Diagram

Evaluation Module Overview www.ti.com

2DLP® LightCrafter™ Display 160CP Evaluation Module DLPU131 – NOVEMBER 2023

Submit Document Feedback

1.4 Device Information

•DLPC3421 (Figure 2-1): display controller controls the DLPA2005 (Figure 2-1) PMIC/RGB illumination driver

and the DLP160CP DMD (digital micromirror device).

•DLP160CP DMD is assembled with an Elephant optical module using SFM-03X-CG and SFM-03X-RAB

LEDs from Luminus with a brightness of 20L out of the box (the module is capable to deliver 50L, but requires

additional thermal designs for proper operation).

•MSPM0G3507 (Figure 2-1): MCU provides control application, nHD image generation through the SSD1963

(Figure 2-1), and UART (Universal Asynchronous Receiver/ Transmitter) (Figure 2-1) communication

programmable capabilities. The MCU can be programmed using ARM® SWD (Serial Wire Debug) interface

through the JTAG (Joint Test Action Group) connector (Figure 2-1).

•SSD1963 (Bridge IC) video interface driver gets 8080 commands from the MCU and outputs RGB666 parallel

interface signals to the DLPC3421 DLP display controller.

•DSI input (Figure 2-1): to the DLPC4321 controller provided through an external interface connector. Video

can be input through an external interface connector over the DSI interface. (Not tested)

•Power button (Figure 2-1) is used to gently power up and power down the DLP display system.

•Programmable push button (Figure 2-1) is used to provide user input controlled by the MCU.

•MicroSD card slot (Figure 2-1) is provided to add custom images controlled by the MCU (MicroSD card not

included).

•USB Type-C power supply interface (Figure 2-1) is used to power the EVM unit (USB Type-C cable and

power supply not included).

This DLP chipset is combined with illumination, projection optics, and RGB LEDs to create a projector that offers

brightness of approximately 20 lumens out of the box for image or informational video display in a very small

volume form factor.

The DLPDLCR160CPEVM is not a production design, and is intended for evaluation only.

www.ti.com Evaluation Module Overview

DLPU131 – NOVEMBER 2023

Submit Document Feedback

DLP® LightCrafter™ Display 160CP Evaluation Module 3

2 Hardware

2.1 EVM Images

Figure 2-1. DLPDLCR160CPEVM Unit (top view)

Figure 2-2. DLPDLCR160CPEVM Unit (perspective view)

Hardware www.ti.com

4DLP® LightCrafter™ Display 160CP Evaluation Module DLPU131 – NOVEMBER 2023

Submit Document Feedback

2.2 Safety Instructions

Cautions and Warnings

WARNING

Observe handling precau



ons. Electrosta



c sensi



ve devices.

CAUTION

Do not stare into opera



ng LED.

Do not leave EVM powered when una



ended.

Cau



on hot surface. Contact may cause burns. Do not touch.

www.ti.com Hardware

DLPU131 – NOVEMBER 2023

Submit Document Feedback

DLP® LightCrafter™ Display 160CP Evaluation Module 5

2.3 Setup

Use the following instructions to set up and run the DLPDLCR160CPEVM.

A 5 V power adapter with a 1 A minimum output and a USB-C connector is required.

Table 2-1. Steps to Use the EVM

Step Action Comments

Power switch (J1) at

OFF position

Power switch (Figure 2-1), J1, needs to be in the OFF

position before power is turned ON to the board. Toggle

lever to the OFF position, opposite direction of the

arrow shown on the board.

TI does not recommend to pull out the power cable or

turn off the input power while the EVM is running. The J1

switch is also used to turn off the EVM before the input

power is turned off.

Connect power supply Connect a USB-C power supply supporting 5 V at 1 A.

Note

Do not use a muti-voltage output USB-C

power adapter.

LED D1 turns on The green LED, D1, lights up to indicate the board is

receiving power.

Power switch (J1) ON Power switch (J1) to the ON position in the direction

of the arrow on the board.

LED D2 turns on The green LED, D2, lights up to indicate the board is in

operational mode.

The RGB LEDs in the Optical Engine (OE) is turned on.

Splash Screen The EVM shows a DLP Logo as a quick power up

slash screen for approximately 1 second.

DLP logo animation A DLP Logo animation using graphics generated by the

MCU plays for approximately 5 seconds.

Main menu A user selectable main menu is displayed.

A description for each menu can be found in Section

2.3.1.

Change menu selection

Quick button (J2) press to cycle through all the menus.

Selected menu button changes to yellow to confirm

menu selection change.

There are 4 main menu options: View images in SD

card, View images in Flash, Control panel demo, and

Reserved.

Menu selections are explained below.

Confirm menu selection Long (>2 sec) button (J2) press to confirm the menu

selection.

The user action results in a button press animation to

confirm selection.

Hardware www.ti.com

6DLP® LightCrafter™ Display 160CP Evaluation Module DLPU131 – NOVEMBER 2023

Submit Document Feedback

2.3.1 Main Menu

After initial powerup and demo display, the push-button switch, SW2, can be used to cycle through the following

four main input/display selections. See Table 2-2 for reference.

Table 2-2. Main Input/Display Selections

Option Description Instructions

MicroSD card Display images from MicroSD card (not

included).

Load content in the MicroSD card per Section 2.3.2. Insert MicroSD

card before selecting the menu. Images on the MicroSD are cycled

on screen. Quick button (J2) press after images start displaying to

pause the images. Long press button to return to the main menu.

Images from Flash memory Display pre-loaded images from display

controller Flash memory.

8 images stored in Flash memory shown individually. Quick button

(J2) press after images start displaying to pause the images. Long

press button to return to the main menu.

Smart Home demo Smart Home user interface demo. MCU

generated images using media library.

Cycle through the Smart Home menus with a quick button press.

Select each menu by long pressing the button. Select the home

icon to return the main menu.

Reserved Reserved space for future capabilities

2.3.2 MicroSD Card Image

Images stored on a MicroSD card can be displayed by the EVM. Images must be stored in an uncompressed,

RGB565 format with nHD (640 x 360) resolution on the card from a computer before inserting in J1, MicroSD

card slot. Images are read out by the MSPM0G3507 MCU before being displayed. Each image is read out by the

MCU and displayed until the new image is transferred. The images on the card are cycled through while in this

mode.

www.ti.com Hardware

DLPU131 – NOVEMBER 2023

Submit Document Feedback

DLP® LightCrafter™ Display 160CP Evaluation Module 7

3 Software

3.1 Programming Instructions

Use the following instructions to program the MSPM0 or the DLPC3421 flash memory.

3.1.1 UART Communication Section

The UART interface is the main communication interface to the EVM through the J3 connector to the

MSPM0G3507. The EVM commands and control can be sent by computer over a terminal interface, or the DLP

EVM GUI program. Please refer to the DLPC3421 Software Programmer’s Guide command and programming

info.

3.1.2 Programming MSPM0 MCU

The MSPM0G3507 MCU can be reprogrammed using either the Uniflash programming tool or the Code

Composer Studio: Theia IDE.

Refer to the following documentation links for more detailed information:

•MSPM0 MCUs Quick Reference Guide

•Code Composer Studio

•MSPM0 SDK

•UniFlash Guide for MSPM0

•UniFlash Quick Start Guide

Refer to Appendix for more detailed EVM MSPM0 programming instructions.

3.1.3 Programming DLPC3421 Display Controller Flash

The DLPC3421 Display Controller flash memory is pre-programmed with a control program binary file.

The EVM GUI can be used to generate a new binary file for programming based on selected options provided

in the GUI. The new binary file can be programmed using the GUI over the UART interface (Not available on

pre-production units). GUI not available on ti.com, to download files needed please request access to MySecure

by writing an email to: [email protected].

Refer to the following documentation links for more detailed information:

•DLPC3421 Software Programmer's Guide

Software www.ti.com

8DLP® LightCrafter™ Display 160CP Evaluation Module DLPU131 – NOVEMBER 2023

Submit Document Feedback

3.2 Appendix

1. Program MSPM0 Controller

a. Items needed (*not included with EVM)

i. XDS110 Debug Probe (TMDSEMU110-U) kit (with included cables & adapters) or LP-XDS110 and

10-pin 2x5 Socket 1.27mm IDC (SWD) cable, purchased separately.*

ii. TI UniFlash programming application.*

iii. MSPM0 software or programming file.*

iv. EVM UUT

v. 5 V Power supply for EVM.*

vi. Computer.*

b. If using the XDS110 Debug Probe, then connect to the computer with USB cable (USB-A to Micro USB

cable included in kit).

c. Connect the 20-pin debug cable to 20-pin debug header on the XDS110 Debug Probe.

d. Connect the ARM® Cortex®-M 10-pin (CM10) adapter to the other end of the debug cable.

e. Connect the CM10 adapter to J1 on the EVM (MSPM0 JTAG connector).

Note

See example of LP-XDS110 and XDS110 Debug Probe Assembly in Figure 3-1, Figure 3-2,

and Figure 3-3.

f. Connect power supply to board.

g. Turn on power to board.

Figure 3-1. LP-XDS110 Debug Probe and EVM

Figure 3-2. XDS110 Debug Probe Assembly

www.ti.com Software

DLPU131 – NOVEMBER 2023

Submit Document Feedback

DLP® LightCrafter™ Display 160CP Evaluation Module 9

Figure 3-3. XDS110 Debug Probe and Board Assembly

2. UniFlash Programming

a. Download and install the TI UniFlash flash programming tool (version 8.4.0 or later) from TI.com at

https://www.ti.com/tool/UNIFLASH.

b. Launch the UniFlash.exe

Note

The XDS110 firmware must be updated to v3.0.0.26 (or newer) to support the MSPM0

devices. The XDS firmware can be updated using the UNIFLASH programming tool.

c. In the New Configuration tab, select the MSPM0G3507 device, and Texas Instruments XDS110 USB

Debug Probe connection:

Software www.ti.com

10 DLP® LightCrafter™ Display 160CP Evaluation Module DLPU131 – NOVEMBER 2023

Submit Document Feedback

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Texas Instruments Scheda madre

Texas Instruments

Texas Instruments LM5000EVAL Manuale utente

Texas Instruments

Texas Instruments DS90UB95x-Q1EVM Series Manuale utente

Texas Instruments

Texas Instruments MSP-US-TRF6901 Manuale utente

Texas Instruments

Texas Instruments TPS62203EVM-211 Manuale utente

Texas Instruments

Texas Instruments DAC 0504 Series Manuale utente

Texas Instruments

Texas Instruments DRV8428EVM Manuale utente

Texas Instruments

Texas Instruments ADS8383EVM Manuale utente

Texas Instruments

Texas Instruments TPA3139D2EVM Manuale utente

Texas Instruments

Texas Instruments TPS54291EVM-431 Manuale utente

Texas Instruments

Texas Instruments CC2530EMK Manuale utente

Texas Instruments

Texas Instruments TRF370315 Manuale utente

Texas Instruments

Texas Instruments TUSB8044RGC Manuale utente

Texas Instruments

Texas Instruments INA228 EVM Manuale utente

Texas Instruments

Texas Instruments TLV840EVM Manuale utente

Texas Instruments

Texas Instruments DRV3946-Q1EVM Manuale utente

Texas Instruments

Texas Instruments TLV320AIC12KEVMB Manuale utente

Texas Instruments

Texas Instruments EK-TM4C123GXL Manuale utente

Texas Instruments

Texas Instruments AN-1975 LMP8640 Manuale utente

Texas Instruments

Texas Instruments bq76PL536PGM-1 Manuale utente

Texas Instruments

Texas Instruments TPA5051EVM Manuale utente

Texas Instruments

Texas Instruments ADS1x9xECG-FE Manuale utente

Texas Instruments

Texas Instruments TVP9900EVM Manuale utente

Texas Instruments

Texas Instruments ONET8501P-EV Manuale utente

Texas Instruments

Texas Instruments DRV8703-Q1-EVM Manuale utente

Manuali Scheda madre popolari di altre marche

DFI

DFI SD170 Manuale utente

ASROCK

ASROCK ROMED8-2T Manuale utente

Asus

Asus P2L97A Manuale utente

Winmate

Winmate IC70 Manuale utente

Asus

Asus MES-B Manuale utente

Grantech

Grantech SYS8F377VGGA-3OMN Manuale utente

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuale utente

Gigabyte

Gigabyte GA-9IVDT Manuale utente

Commell

Commell MS-C73 Manuale utente

IBT Technologies

IBT Technologies MB860 Manuale utente

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuale utente

Biostar

Biostar M7VIT Bravo Istruzioni per l'uso e l'installazione

Intel

Intel D33217CK Manuale utente

Asus

Asus F1A55-M LX PLUS R2.0 Manuale utente

EPC

EPC EPC9147C Manuale utente

Asus

Asus EX-B760M-V5 D4 Manuale utente

EPOX

EPOX MU-8KHA0010 Manuale utente

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manuale utente