TKH SVS-Vistek MotionBLITZ Cube6 Manuale utente

MotionBLITZ® Cube6

User Guide

Valid for MotionBLITZ Director2

Software version 2.0

Contents

1Before you start 6

1.1 About this manual 6

1.1.1 Tips, remarks, and notes 6

1.1.2 Registered trademarks 6

1.1.3 Conformity and use 6

1.1.4 Supplements 7

1.2 Warranty and non-warranty clause 8

1.3 Support 8

2Introduction 9

2.1 Intended use 9

2.2 Scope of delivery 9

2.3 Optional accessories 9

2.4 System requirements 9

3The camera 10

3.1 Camera description 10

3.2 Operating temperature 11

3.3 Additional cooling 11

3.4 Interfaces of the camera 12

3.4.1 Status LEDs 13

3.4.2 GigE interface 13

4First steps 15

4.1 Connecting the camera 15

4.2 Connecting external signals 16

4.2.1 Connecting the trigger input and SyncIN 16

4.2.2 Sync input timing 16

4.2.3 Sync/ARM output 17

4.2.4 Trigger connection 17

4.2.5 Trigger signal pulse width 18

4.2.6 Trigger signal processing 18

4.2.7 Analog input signal definition 18

4.2.8 Digital inputs 1-3 signal definition 18

4.3 Connecting an all signal cable 19

4.4 Manually assigning an IP address 19

4.5 Using multiple network cards 21

4.6 Accelerating the network speed 22

4.7 Switching to standby mode 23

4.8 Cleaning sensor and lens 24

4.9 Charging the battery 24

4.10 Replacing the battery 24

4.11 Troubleshooting 25

5The MotionBLITZ Director 2 software 26

5.1 Introduction 26

5.1.1 Supported cameras 26

5.1.2 System requirements 26

5.1.3 Installing the software 26

5.2 The user interface 27

5.2.1 Starting the software 27

5.2.2 The user interface 27

5.2.3 Connecting the camera 28

5.3 Settings 29

5.3.1 Overview 29

5.3.2 Camera settings 29

5.3.3 Camera IO 31

5.3.4 Record settings 34

5.3.5 Program settings 38

5.3.6 Advanced settings 41

5.4 Display window 43

5.4.1 Display window icons 43

5.4.2 Gamma correction panel 44

5.4.3 Bayer adjustment (white balance) 45

5.4.4 Open images 47

5.4.5 Image export 49

5.5 Recording 51

5.5.1 Overview 51

5.5.2 Start recording 51

5.5.3 Stop recording 51

5.5.4 Playback 51

5.5.5 Select a sequence 52

5.5.6 Remove a sequence 53

5.5.7 Save a sequence 53

5.5.8 Export directory 54

5.5.9 Available space 54

5.5.10 Export name 54

5.6 Multi-camera mode 55

5.6.1 Overview 55

5.6.2 MultiCam playback 55

5.6.3 Save a MultiCam sequence 56

5.6.4 Open a MultiCam sequence 56

6Technical data 57

6.1 Camera specifications 57

6.2 Sensor specifications 58

6.3 Resolution and speed 58

6.4 Camera dimensions 59

6.5 Pin assignments 60

6.5.1 Power connector 60

6.5.2 Trigger connector 60

6.6 Spectral response 61

6.6.1 Monochrome and color with UV/IR Cut Filter 61

6.6.2 Monochrome and color without UV/IR Cut Filter 62

7Appendix 63

Declaration of Conformity 64

Figures

Fig.: 3-1: Interfaces of the camera MotionBLITZ® Cube6 12

Fig.: 4-1: Connecting camera and image processing system 15

Fig.: 4-2: Trigger / Sync input signal definition 16

Fig.: 4-3: Sync / ARM output 17

Fig.: 4-4: Trigger connection 18

Fig.: 4-5: Trigger signal pulse width 18

Fig.: 4-6: Digital inputs 1-3 signal definition 18

Fig.: 5-1: User interface 27

Fig.: 5-2: Available cameras 28

Fig.: 5-3: Adjusting the ROI 30

Fig.: 5-4: Camera IO 31

Fig.: 5-5: Analog input converter 33

Fig.: 5-6: Ring mode 35

Fig.: 5-7: Recording sequences 36

Fig.: 5-8: Multi-sequence recording 37

Fig.: 5-9: Program settings 38

Fig.: 5-10: Advanced settings 41

Fig.: 5-11: Dynamic range adjustment 42

Fig.: 5-12: Display window 43

Fig.: 5-13: Adjusting white balance manually 46

Fig.: 5-14: Histogram 47

Fig.: 5-15: Multiple files side by side 48

Fig.: 5-16: Image export dialog 49

Fig.: 5-17: Save a sequence 53

Fig.: 5-18: Select images 53

Fig.: 5-19: MultiCam mode 55

Fig.: 6-1: C-mount 59

Fig.: 6-2: F-mount 59

Fig.: 6-3: Pinning of matching power plug (solder side) 60

Fig.: 6-4: Trigger connector 60

Fig.: 6-5: Quantum Efficiency mono and color with UV/IR Cut Filter 61

Fig.: 6-6: Quantum Efficiency mono and color without UV/IR Cut Filter 62

1 Before you start

1.1 About this manual

This manual contains helpful information to install and operate the described cam-

era. It has been produced with care. Nevertheless, information might be erroneous or

incomplete. Mikrotron GmbH cannot be held responsible for any problems resulting

from incomplete or erroneous information.

In case you detect errors or need further information, please inform us via mail:

[email protected] or

Call +49- 89-7263-4200

We highly recommend to read this manual carefully.

NOTICE This manual is subject to change without notice.

It is intended for staff with technical qualifications who have been specially trained

and have the appropriate knowledge in the field of automation technology, electrical

and optical devices.

INFO Keep this manual for future use.

1.1.1 Tips, remarks, and notes

This manual contains tips and notes that help to avoid data loss or camera damage.

They are emphasized as follows:

INFO Provides information that may help to improve camera handling or avoid data loss.

NOTICE Provides information to avoid damage to the system.

1.1.2 Registered trademarks

In this manual the following registered trademarks may be used:

nMotionBLITZ®

nImageBLITZ®

nEoSens®

nGenICam®

nMicrosoft® and Windows®

nIntel®

Throughout the manual, these trademarks are not specifically marked as registered

trademarks. This in no way implies that these trademarks can be used in another con-

text without the trademark sign.

1.1.3 Conformity and use

This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to Part 15 of the FCC Rules. These requirements are

designed to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment.

1 Before you start 6

This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions given in this guide, may cause

harmful interference to radio communications. Operation of this equipment in a res-

idential area is likely to cause harmful interference in which case the user will have to

correct the interference at its own expense.

NOTICE You are herewith cautioned that any changes or modifications not expressly

approved in this description could void your authority to operate this equipment.

制造说明：

此设备的生产与测试依照FCC条例第15条条例，符合A类电子设备标准。产品提

供在商用使用环境中的合理保护，以防止使用过程中可能涉及到的损害。

此设备会产生、使用并可发射出无线电波，如果未按照本手册中所述安装和使

用，可能会对无线通信设备产生干扰。如本设备在居民区操作出现干扰等情

况，用户需要自费处理。

备注：请注意，如未按照此使用说明操作而自行更改设备，那么您将无权使用

本设备。

規制適合宣言とご使用について(米国FCC)

この機器は、FCC規則のパート15に定められたクラスAデジタル装置に関する規制

要件に基づいて所定の試験が実施され、その適合が認証されています。これらの

規制要件は、商業環境において機器を使用する際、有害な干渉に対する妥当

な保護を提供するために設けられています。この機器は、無線周波数エネルギー

を生成かつ利用するとともに、放射することもあります。このリファレンスガイドの指

示に従って設置および使用が行われない場合は、無線通信に有害な干渉を引き

起こす恐れがあります。この機器を住宅地で利用すると有害な干渉を起こすこと

もあり、その場合、使用者は自己負担において適切な対策を講じる必要がありま

す。

注意事項：このリファレンスガイドに明示的に承認していない変更や修正を行った

場合には、本製品を使用する権利が無効となることがあります。

1.1.4 Supplements

For customers in Canada

This apparatus complies with the Class A limits for radio noise emissions set out in

Radio Interference Regulations.

Pour les utilisateurs au Canada

Cet appareil est conforme aux normes Classe A pour bruits radioélectriques, spé-

cifiées dans le Règlement sur le brouillage radioélectrique.

1 Before you start 7

Life support applications

The products described in this manual are not designed for use in life support appli-

ances or devices and systems where malfunction of these products can reasonably be

expected to result in personal injury.

NOTICE Mikrotron customers using or selling these products for use in such applications do

so at their own risk and agree to fully indemnify Mikrotron for any damages res-

ulting from such improper use or sale.

1.2 Warranty and non-warranty clause

Warranty is described in §8 of our General Terms and Conditions which can be

downloaded on the Mikrotron web page (www.mikrotron.de/en/terms.html).

In addition, take the following non-warranty clauses into account.

NOTICE The camera does not contain serviceable parts. Do not open the body of the cam-

era. If the camera has been opened, the warranty will be void.

NOTICE The camera has to be used with a supply voltage according to the camera’s spe-

cification. Connecting a lower or higher supply voltage, AC voltage, reversal polar-

ity or using wrong pins of the power connector may damage the camera. Doing so

will void warranty.

Our warranty does not protect against accidental damage, loss, or acts of nature.

INFO Mikrotron cannot be held responsible for the loss of data. We recommend a backup

plan.

1.3 Support

1. In case of support or a warranty claim, make a note of the camera type and its

serial number (S/N). You find all necessary information on the identification

plate of the camera.

2. Contact us in one of the following ways:

oContact us via email: [email protected]. Our support team will guide

you through the process.

oOr visit our support website

www.mikrotron.de/en/services/support.html

and fill out the form. You will receive an automatic reply from our ticket sys-

tem.

1 Before you start 8

2 Introduction

2.1 Intended use

The camera MotionBLITZ® Cube6 belongs to the product class of so-called record-

ing cameras that can be used for a variety for purposes.

Recording cameras are designed to capture and record fast movement, processes or

short events and replay at slower speed, for example for slow-motion replay of move-

ments in sports, during manufacturing processes, or for scientific research.

Other uses

Any other use is regarded as unintended use and leads to the loss of guarantee and

liabilities. Contact the manufacturer for other uses.

These products are designed for industrial applications only. The cameras are not

designed for life support systems where malfunction of the products might result in

any risk of personal harm or injury.

2.2 Scope of delivery

The following components are part of delivery. Before installing the camera, check if

the delivery is complete:

nEoSens MotionBLITZ Cube camera as ordered

nShielded Gigabit Ethernet interface cable for each camera

nPower supply (110 – 220 V) with cable (5 m) and 12-V-connector (plug)

nUSB storage device with Director2 software and documentation

nLens as ordered

2.3 Optional accessories

nHand trigger cable; part no. KKRTMBC05L (5 m) or KKRTMBC10L (10 m)

nAll signal cable: part no. KKRKAVERTIOCU03 (3m)

2.4 System requirements

The PC or image processing system that is connected with the camera must be

equipped with:

nWindows 7/8/10 (or higher) operating system

n1Gbit Ethernet controller to control the camera. To reach high data transfer

rates via Ethernet, the Ethernet controller should support jumbo frames that can

carry up more than 8MB of payload.

nEither MotionBLITZ® Director2 software or a GenICAM SDK

INFO Cube cameras can easily be parametrized and controlled by MotionBLITZ® Dir-

ector2 software. For further information, refer to the Reference Guide of the camera.

2 Introduction 9

3 The camera

3.1 Camera description

Due to the built-in ring memory, the high-speed camera can also be used without a

connection to a notebook or PC. Up to 13 seconds can be recorded at full resolution

and speed without complicated experiment setup.

Cube cameras provide an outstanding performance and therefore are efficient ana-

lysis tools e.g. to monitor and optimize processes. In extreme situations such as dif-

ficult lighting conditions, varying temperatures, vibrations or jolting MIKROTRON

high-speed Cube cameras deliver frames reliably.

The camera MotionBLITZ® Cube6 is available in monochrome and color.

Initially, frames are stored in the internal frame memory of the camera. If the built-in

rechargeable battery of the camera is completely charged, it operates up to

60minutes autonomously in record mode and stores recorded data in the internal

frame memory for up to 2hours.

The color and monochrome cameras are supplied with the following features:

nAnalog / Digital gain

nAutosave mode

nDefective pixel correction

nImageBLITZ

nImage information field

nIRIG-B support

nMulti-sequence mode (1...32)

nQuad mode

nRecord until end

nRing mode

Bayer filter

The sensor of the EoSens color cameras is supplied with a Bayer color filter. In order

to get the color information, the imaging software has to decode the information of

each pixel into red, green, and blue (RGB) by using the values of its neighboring

pixels. Each red, green and blue filter element covers exactly one pixel on the sensor.

A matrix of 2x2 filter elements builds a filter element matrix. A Bayer pattern image

therefore must have an even number of pixels and an even number of lines. The

ordering of the RGB pixels for each sensor is provided in the section on technical

data.

UV/IR cut filter

In addition, color cameras are equipped with an UV/IR cut filter. Light with

wavelengths between 370nm and 670nm will be transmitted. As CMOS sensors are

susceptible to UV and IR rays outside the visible spectrum, UV/IR filter avoid blurred

images and therefore improve color images.

3 The camera 10

Indice

Manuali Sistema di visione artificiale popolari di altre marche

Festo

Festo SBOC-M-R1B-H Manuale utente

Banner

Banner VE200G1B Manuale utente

SVS-Vistek

SVS-Vistek CoaxPress EoSens Creation 1.1CXP2 Manuale utente

Sony

Sony Vision Exchange PEQ-C100 Manuale utente

Datalogic

Datalogic MX-U81 Istruzioni per l'installazione

Cognex

Cognex In-Sight D900 Series Manuale utente

Spektrum

Spektrum SPMVR2520 Manuale utente

Huaray

Huaray Movidius Series Manuale utente

Daheng Imaging

Daheng Imaging MERCURY2 USB3 Manuale utente

SVS-Vistek

SVS-Vistek exo174 U3 Series Manuale utente

Teledyne

Teledyne e2v Eliixa+ Series Manuale utente

Photron

Photron FASTCAM Mini CX Series Manuale utente

National Instruments

National Instruments Vision CVS-1455 Manuale utente

Omron

Omron FH-L550 Manuale utente

iGen

iGen NV20/20 Manuale utente

JAI

JAI GO-5100MP-USB Manuale utente

Ark Vision Systems

Ark Vision Systems AVS-Monitor 7 FHD Manuale utente

Cognex

Cognex In-Sight 9902L Manuale utente