TOORX BRX90 Manuale utente

Ed : 02/17

INSTRUCTION

Rev : 0000

All data displayed are approximate guidance and cannot e used in any medical application.

ASSEMBLY INSTRUCTIONS

Step 1

Assem ly the rear and front sta ilizer (N&M)

with 4 olts (M-1).

Step 2

Assem le the left hand pedal (K-L) and the

right hand pedal (K-R) to the crank.

Step 3

Pass through the handle ar post (C) from

the plastic cover (I-1).

Connect the computer ca le up and down

(C-5 & E-4). Fix the handle ar post to the

main frame after the a ove two steps.

Fasten those screws （E-2） and washers

(E-3&E-8) to fix the handle ar post, move

the plastic cover to right position.

ASSEMBLY INSTRUCTIONS

Step 4

Attach the handle ar (B) to the handle ar

post etween the steel covers, secure the

steel cover assem ly using one flat washer

(C-1), one spring washer (C-2), one ushing

(C-3) and one kno (C-4).

Step 5

Plug in the ca les (A-1&B-2) etween the

computer and the handle ar post, plug in

the motor ca le (A-2&C-5) etween

computer and handle ar post.

Fix the computer onto the handle ar post

with four screws (A-3).

ASSEMBLY INSTRUCTIONS

Step 6

Insert the seat post (D) into the main frame

through the plastic sleeve. Select the ideal

hole position on the seat post. Insert the kno

(E-6) into the hole. Tighten fully the kno .

Step 7

Connect the saddle (D-6) and the slider (D-

5) s.

Attach the slider onto the top of the seat

post and the secure using the horizontal

adjusting kno (D-1) and one flat washer (D-

2).

Step 8

Put the handle ar plastic cover left & right

(C-11&C-6) onto the handle ar, secure it with

screws (C-8&C-9) as left drawing.

Step 9

Assem le the slider cover left & right (D-

8&D-7) onto the slider set, fix it with screws

(C-8&D-9).

PARTS LIST

Item Description Q’ty Item Description Q’ty

A Computer 1 F-7 C-circle 1

A-1 Pulse ca le (upper) 1 G Idle 1

A-2 Motor ca le 1 G-1 Nylon nut M8 5

A-3 Screw M5*10 4 G-2 Bushing Φ10*Φ14*6L 2

B Handle ar 1 G-3 Idle wheel 1

B-1 Screw M4*20 2 G-4 Flat washer 2

B-2 Pulse ca le (lower) 2 G-5 Screw M8*20L 1

B-3 End cap 2 G-6 Spring 1

B-4 Foam grip 2 H Flywheel 1

B-5 Hand pulse 2 H-1 Screw 3/8″-26 5

C Handle ar post 1 H-2 Bearing 6000 1

C-1 Flat washer 1 H-3 Bearing 6300 1

C-2 Spring washer 1 H-4 One way earing 1

C-3 Bushing 1 H-5 Bearing 6203 1

C-4 Kno 1 H-6 Small elt pulley 1

C-5 Motor ca le (upper) 1 H-7 Bearing 6003 1

C-6 Handle ar cover (right) 1 H-8 Mandril of flywheel 1

C-7 Screw 4 I-L Chain cover (left) 1

C-8 Screw 2 I-R Chain cover (right) 1

C-9 Handle ar cover (left) 1 I-1 Handle ar post cover 1

D Seat post 1 I-2 Screw M4*20 5

D-1 Seat kno 1 I-3 Screw 12

D-2 Flat washer 1 I-4 Rear tu e cover 1

D-3 Cap 20*40 2 J-L Crank (left) 1

D-4 Slider fixed screw 1 J-R Crank (right) 1

D-5 Slider 1 J-1 Screw M8 2

D-6 Saddle 1 J-2 Cover for crank 2

D-7 Slider cover (right) 1 K-L Pedal (left) 1

D-8 Slider cover (left) 1 K-R Pedal (right) 1

D-9 Screw 2 L Magnetic set 1

E Main frame 1 L-1 Screw M6 2

E-1 Bearing 6203 2 L-2 Spring 1

E-2 Screw M8*16L 5 L-3 Magnetic 10

E-3 Flat washer 4 L-4 Bushing 1

E-4 Motor ca le (lower) 1 L-5 Wave washer 2

E-5 Plastic sleeve 1 L-6 C circle 2

E-6 Seat post kno M16 1 L-7 Spring washer 2

E-7 Screw 1 L-8 Flat washer 2

E-8 Semicircle washer 1 M Front sta ilizer 1

E-9 Motor 1 M-L Front end cap (left) 1

F Plastic pulley 1 M-R Front end cap (right) 1

F-1 Bushing Φ17*5T 1 M-1 Screw M8*60L 4

F-2 Axle assem ly 1 N Rear sta ilizer 1

F-3 Screw M8*10L 3 N-L Rear end cap (left) 1

F-4 Belt 1 N-R Rear end cap(right) 1

F-5 Wave washer 1 O Inner hex. wrench 1

F-6 Flat washer 1 P Harpoon wrench 1

COMPLETE BIKE ASSEMBLY

Computer Operation

I. To operate the monitor

A-0. Plug in the AC Adapter to power supply. You will see this first screen followed by the next one.

A-

1. You may select different training mode of MANUAL, PROGRAM, USER or TARGET H.R. by pressing UP, DOWN buttons (a1).

Press MODE button to confirm. Or, you may press ST/STOP button to start training directly in MANUAL mode.

A-

2. In a fresh monitor, if you start the selected mode, all function data start counting up from zero once the training st

arts (a2).

If you choose t

o preset any function target data (optional), then, the function display will count down from your preset target

value once the training starts.

A-

3. During training, you may adjust resistance by pressing UP, DOWN buttons (a3). Please note each bar represe

nts TWO

resistance levels. The bar will change up or down every two levels. During adjustment, you will see the display changes

when you press UP or DOWN button twice. There is a number (1 to 16) on the screen to show the exact resistance level.

A-4. To reset, press and hold the RESET button for 2 seconds.

(a1)

(a2)

(a3)

B. Training in MANUAL mode - press UP button until MANUAL shows up on the upper line, press MODE to confirm(b1).

(b1)

(b2)

(b3)

(b4)

B-1 You may press ST/STOP button to start t

raining directly(b2), or you may press UP, DOWN buttons to adjust resistance

level (b3). During adjustment, you will see the display

changes when you press UP or DOWN buttons twice.

You may also adjust training resistance during training.

B-2 After adjustment of the training resistance, you may press

ST/STOP to start training or, optionally, set each function

(b5)

(b6)

data target by pressing MODE button to select the desired function you want to set target data. Then, use the UP, DOWN

buttons to set the v

alue. Press MODE button to advanced to the next desired function area. The functions available for

preset are: Time, Distance, Calories, and Pulse in MANUAL mode.(b4)

B-3 After all settings are done, press ST/STOP button to start training. You will see each preset function data counts down from

target as soon as training starts. (b5)

B-4

Once each function target data is achieved (counts down to zero), the monitor will stop all functions (P appears on the

left-upper corner) and beep for 8 times to remind you. (b6)

B-5

You may press ST/STOP button to start training again. The function which has achieved to zero will start from previous set

data counting down, and other set function data will keep counting up or down from previous records.

Indice

Manuali Cyclette popolari di altre marche

Weslo

Weslo Vector 302 Guida rapida

Matrix

Matrix KranKcycle Manuale utente

Matrix

Matrix IC3 Manuale utente

Sunny Health & Fitness

Sunny Health & Fitness SF-B121021 Manuale utente

Monark

Monark 827E Manuale utente

Stamina

Stamina 1310 Manuale utente

American Fitness

American Fitness SPR-BK1072A Manuale utente

Cateye

Cateye CS-1000 (CYCLO SIMULATOR) Manuale utente

BH FITNESS

BH FITNESS H9158H Manuale dell'operatore

Body Sculpture

Body Sculpture BC-7220G Manuale utente

Cateye

Cateye EC-2300 Manuale utente

FYTTER

FYTTER RACER RC MSR Manuale utente

Kikos

Kikos HM-9090M Manuale utente

Pro-Form

Pro-Form 345 Zlx Bike Guida utente

Fuel Fitness

Fuel Fitness SU135-40 Manuale utente

NordicTrack

NordicTrack Gxr 4.2 Bike Manuale utente

Vision Fitness

Vision Fitness U70 Manuale utente

Stamina

Stamina 15-0340A Manuale utente