TP-Link EcoNET300 Scheda tecnica

OPERATION AND INSTALLATION MANUAL

ISSUE: 1.1

APPLIES TO THE REGULATOR:

•boiler, series: ecoMAX800 (excluding ecoMAX800R1,T1), ecoMAX850, ecoMAX860, ecoMAX910/920

•solar: ecoSOL301/400

•heat pump, series: ecoTRONIC100/200

•ventilation, seria: ecoVENT

INTERNET MODULE

ecoNET300

REMOTE CONTROL OF REGULATORS

09-2017

www.econet24.com

ecoNET.apk

ecoNET.app

 
 
CONTENS OF TABLE 
 
INFORMATION ABOUT DOCUMENTATION......... 4 
APPLIED SYMBOLS .............................................. 4 
DYREKTYWA WEEE 2012/19/UE ................................. 4 
INFORMATIONS .................................................. 5 
SAFETY ................................................................ 5 
COOPERATION WITH REGULATORS.................... 6 
CONNECTION TO THE REGULATOR..................... 6 
1 CONNECTION WITH ECOMAX800 SERIES ................. 6 
2 CONNECTION WITH ECOMAX850 SERIES ................. 6 
3 CONNECTION WITH ECOMAX860 SERIES ................. 7 
4 CONNECTION WITH ECOMAX910/920 SERIES.......... 8 
5 CONNECTION WITH ECOSOL .................................. 8 
6 CONNECTION WITH ECOTRONIC SERIES................... 8 
7 CONNECTION WITH ECOVENT SERIES ...................... 9 
CONNECTION WITH INTERNET ........................... 9 
LOGGING TO THE MODULE FROM THE LOCAL 
LAN 11 
LOGGING TO ECONET ACCOUNT ...................... 11 
1 FIRST LOGGING TO ECONET ACCOUNT ................... 11 
WEBSITE SUPPORT............................................ 12 
1 CURRENT DATA.................................................. 13 
2 DIAGRAM......................................................... 13 
3 USER AND SERVICE PARAMETERS........................... 13 
4 HEAT YIELD GRAPH ............................................. 13 
5 DATA HISTORY................................................... 13 
6 ALARMS........................................................... 14 
7 SCHEDULE ........................................................ 14 
8 FUEL CONSUMPTION........................................... 15 
9 DEVICE SETTINGS ............................................... 15 
MOBILE APPLICATION ....................................... 15 
RESTORING DEFAULT USER NAME AND 
PASSWORD ................................................................... 16 
 
 

1. Information about documentation

The manual is a supplement for the regulator

manual. In particular, except for this manual,

the regulator manual should also be

observed.

We are not responsible for any damages

caused by failure to observe these

instructions.

2. Applied symbols

In this manual the following graphic symbols

are used:

- the sign means that the posted

information has an impact on safety,

- the sign indicates that the

information provided relates to the

features of the module.

4. Dyrektywa WEEE 2012/19/UE

Purchased product is designed and made of

materials of highest quality.

The product meets the requirements of the

Directive 2012/19/EU of 4 July 2012 on

waste electrical and electronic

equipment (WEEE), according to which it is

marked by the symbol of crossed-out

wheeled bin (like below), meaning that

product is subjected to separate collection.

Responsibilities after finishing a period of

using product:

•dispose of the packaging and product at

the end of their period of use in an

appropriate recycling facility,

•do not dispose of the product with other

unsorted waste,

•do not burn the product.

By adhering obligations of waste electrical

and electronic equipment controlled disposal

mentioned above, you avoid harmful effects

on the environment and human health.

3. Informations

The internet module enables regulator

operation remote control (on-line) via

Internet or a (LAN/Wi-Fi) local network. User

can remotely monitor operation of the

regulator and modify operation parameters

of the regulator controller with the use of a

computer, a tablet or mobile phone.

Essential features of the module:

•the ecoNET300 integrated WWW server

enabling remote control of operation of

the regulator within a local network

without Internet access,

•cooperation with www.econet24.com

external server provides access to

regulator via Internet,

•supports Wi-Fi wireless networks,

•preview of current operation parameters

of the regulator in readable and clear

“tiles”,

•visualization via readable hydraulic

diagram indicating current operation of

the hydraulic system,

•preview and edition options of most (user

and service) parameters of the regulator,

•registration of operation parameters and

alarm conditions of the regulator,

•possibility of e-mail notifications

concerning alarm conditions of the

regulator.

4. Safety

In any circumstances do not modify

construction of the device.

Device can be started and connected only by

a person who read this manual.

Connecting the internet module not in

accordance with the manual or improperly

can result in inappropriate operation of the

controller or interruption of its operation.

Verify if regulator software is adapted to

cooperate with ecoNET300 internet module.

Do not use the device for other than

intended use.

Always turn off the regulator before

connecting the internet module.

5. Cooperation with regulators

Check regulator software version before

connecting a ecoNET300 module with the

regulator.

In the regulator main menu select tab:

MENU →Information →Software version

User can contact with the regulator

manufacture in order to verify whether a

particular type of regulator will be

cooperating with ecoNET300 according to

data concerning regulator software versions.

6. Connection to the regulator

The ecoNET300 internet module has to be

connected with regulator with the use of

ecoLINK2 interface. In case of some types of

regulators it is necessary to use an

appropriate adapter.

The ecoLINK2 interface and adapter are a

part of the ecoNET300 set.

Adapter: 1 - socket for RJ11 ecoLINK2 interface, 2

- a plug for regulator module transmission socket,

3 - socket for a control panel plug.

6.1 Connection with ecoMAX800

series

This chapter applies to ecoMAX800 P1, P2,

R2, T2, D1, D2 regulators. It is not applicable

to ecoMAX800R1 and ecoMAX800T1.

In case of ecoMAX800 series, a EL2adapter

or El2adapter v2 must be used in order to

connect ecoLINK2.

6.2 Connection with ecoMAX850

series

The ecoMAX850P1 or ecoMAX850D1

regulator modules are equipped with an

additional COM transmission socket to

connect RJ11 plug of ecoLINK2 interface

without using any adapters. Just unscrew the

regulator housing and put the plug into a

COM socket.

In order to connect the ecoNET300 module

with the regulator, ecoLINK2 interface is

required which is a part of the set.

The internet module will cooperate only with

regulators with installed software supporting

ecoNET300 module.

Connection with ecoMAX850P1, D1: 1 –COM

socket (place of plugging a RJ11 interface plug), 2

–a socket with connected plug of the control

panel, 3 –regulator housing cover (possible place

where a control panel can be assembled).

Modules of ecoMAX850P2 controllers are

equipped with just one COM transmission

socket in RJ11 standard which a control

panel (located inside or outside the controller

housing) is connected to. Using one RJ11

socket in the module requires connecting an

additional divider (telephone RJ11 tee

separator) and additional cable.

Standard divider, RJ11 telephone divider: 1-

connection of RJ11 ecoLINK2 interface plug, 2-

connection of the control panel plug, 3-

connection of an additional cable with two RJ11

terminals.

Standard RJ11 telephone cable with an option of

connecting wires and a method of connecting into

the divider.

Below show location of the regulator COM

transmission socket, where: interface

ecoLINK2,on diagram includes: COM

transmission socket (connection point

between cable and divider), divider, control

panel, additional ecoSTER TOUCH control

panel (in ecoMAX850I version) and

ecoSTER200, additional cable to a divider.

6.3 Connection with ecoMAX860

series

In case of ecoMAX860P1, P2, P3 series, a

El2adapter v2 must be used in order to

connect ecoLINK2 interface.

P1 version:

P2 version:

P3 version:

6.4 Connection with ecoMAX910/920

series

In case of ecoMAX910, 920 series, the

ecoLINK2 interface must be connected

directly to the regulator's RJ11 socket.

6.5 Connection with ecoSOL

In case of ecoSOL301, 400, 500 series, the

ecoLINK2 interface must be connected

directly to the regulator's RJ11 socket.

6.6 Connection with ecoTRONIC

series

In case of ecoTRONIC100, 200 series, a

El2adapter v2 must be used in order to

connect ecoLINK2 interface.

6.7 Connection with ecoVENT series

The Internet module must be connected to

the regulator module via the ecoLINK2

interface, without the RJ11 plug (according

to the interface label).

Connect the conductors of the interface cable

to the regulator terminals together with the

conductors of the control panel cable.

OEM version:

MAXI version:

7. Connection with Internet

Connect adapter plug to a mini USB Port

socket and 3G USB Port to the ecoLINK2

interface. Connect with RJ45 Ethernet Port

with Ethernet cable, e.g. with ADSL router,

switch and modem. A socket does not have

to be use in case of Wi-Fi wireless network

access. The Mode Switch can be set in any

position.

Connection of ecoNET300 with ETHERNET RJ45

with access points of LAN wire Internet network or

with Wi-Fi wireless network.

The ecoNET300 requires constant access to a

wire LAN or wireless Wi-Fi network in a place

of installation of the regulator.

mini USB Port

3G USB Port

RJ45 Ethernet Port

Mode Switch

LED

condition

Module operation

condition

Power

Power on.

OFF

Power off.

Connection

with a

regulator

Active connection of the

regulator.

OFF

No connection with

regulator.

Connection

with WiFi

Connection to a

programmed wireless

network is on.

OFF

No connection with

wireless network.

Connection

with a server

Connection with

www.econet24.com

external server is on.

OFF

No connection for

www.econet24.com

external server.

After the power is on, ecoNET300 requires

app. 1 minute in order to load the

operational system. Then, the module begins

to work and indicates its condition with LED

indicators. In a connection between

ecoNET300 module with a regulator is active,

a “ connection with controller” indicator

lights up. New functions for managing

ecoNET300 module are added to the main

menu.

MENU →Information →ecoNET WiFi

MENU →Information →ecoNET Ethernet

MENU →Main settings →WiFi

In case of connection with LAN wire network,

a ecoNET Ethernet tab will be available in

regulator menu from which the IP number,

mask and gate can be read out and

ecoNET24 server connection condition can be

checked. It is required to save the displayed

IP number (e.g. IP:10.1.2.237). This

number in a form of: http://10.1.2.237 is

entered into the address field from the level

of LAN network. A website to operate the

regulator menu will be activated.

It is necessary to enter network parameters

in General settings menu of the control

panel in order to make a wireless connection

via Wi-Fi.

To do this, select:

MENU →general settings →WiFi (WiFi

settings)

Select SSID in Network Settings. It is a

name of the local wireless network which has

to be the same for all devices working in this

network (SSID can be, e.g.: myWiFi).

In case of connection with a chosen Access

Point via wireless network, user has to know

the settings of Wi-Fi network which the

module will be connected to: network name

(SSID), protection type, access password.

The ecoNET300 requires active DHCP server

of Access Point (e.g. router) because

manual IP assignment for ecoNET300

internet module is not supported. More

information can be obtained from router

configuration software or network

administrator.

WPS/RESET button. Deleting user name

and password and restoring default

settings. User: admin, password: admin.

Works only in local version.

The LED indicators of module operation

condition.

Indice

Altri manuali TP-Link Unità di controllo

TP-Link

TP-Link kasa smart KE100 Manuale utente

TP-Link

TP-Link kasa smart KE100 Manuale utente

TP-Link

TP-Link KLM100 Manuale utente

TP-Link

TP-Link DS-PMA-C+ V1 Manuale utente

TP-Link

TP-Link kasa smart KE100 V1.20 Manuale utente

TP-Link

TP-Link TL-SM311 Series Manuale utente

TP-Link

TP-Link TL-SM321A Manuale utente

TP-Link

TP-Link TL-SM331T Manuale utente

TP-Link

TP-Link TL-SM311LS Manuale utente

TP-Link

TP-Link TL-SM331T Manuale utente

TP-Link

TP-Link TL-SM201 Series Manuale utente

TP-Link

TP-Link Kasa Smart KE100 KIT Manuale utente

TP-Link

TP-Link TL-SM321A Manuale utente

TP-Link

TP-Link TL-SM321A Manuale utente

TP-Link

TP-Link kasa smart KE100 Manuale utente

TP-Link

TP-Link Omada SM311LS V5 Manuale utente

TP-Link

TP-Link TL-SM321A Manuale utente

TP-Link

TP-Link TL-SM311LS Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente

TP-Link ecoNET300 Scheda tecnica

Manuali Unità di controllo popolari di altre marche