TP-Link TL-WA5110G Manuale utente

Note

Note Please use only wired network connections to configure the AP.

The power adapter can be directly connected to the AP too. In this way

you can connect your computer directly to the AP with an Ethernet cable.

Turn off all your network devices,

including your computer(s), powe

injector and the AP.

Connect your computer to the

LAN port on the power injecto

with an Ethernet cable.

Plug the provided power adapte

into the DC jack on the powe

injector, and the other end to a

standard electrical wall socket.

Connect your AP to the PoE port

on the power injector with an

Ethernet cable.

Note If the LEDs display abnormally, please check to see if all the cable connectors

(power adapter and Ethernet cable) are well connected to your device.

Solid light

Flashing if the Wireless Radio

function is enabled

Solid light or flashing

Flashing

Turn on all your network devices and then check to see if the LEDs on the AP

display normally as the diagram below describes.

Note You will need to assign your computer a Static IP address within the

same range as the AP’s IP address. See the Troubleshooting T3 if you

need assistance.

Open your web browser and

type in http://192.168.1.254

in the address bar and press

Enter

Click OK

Click Quick Setup

Click Next

Operation Mode Setting

dialog box will prompt you for the

User name and Password. Enter

the default values and click OK.

Note If the dialog box does not pop up, please refer to T3 in the Troubleshooting

guide. T2 will give you some help if you forget the password.

The web management page will

display after successfully logging

in.

User name: admin

Password: admin

This page will then display.

Click Next

Choose the Operation Mode

Type appropriate to your needs

A. Configuration for WISP Client (CPE)

After choosing the AP Client Router mode on the above page, this page will then

display.

The Username and Password are provided by your WISP.

Click Next

Choose your WAN Connection

Type provided by your WISP.

Here we choose PPPoE as an

example

Enter the Username and Password

given by your WISP

Click Next

Enter the SSID provided

our WISP

Click Next

Click Finish

Click Finish to exit the Quick Setup

wizard and wait until the AP completes

rebooting automatically. The changes

will take effect after rebooting.

The AP supports three operation mode types: AP Client Router,

P Route

and AP.

a) If you want to connect to your WISP, please choose

P Client

Router mode and proceed to AǗ

b) If you want to configure a point to point connection, please skip to B;

c) If you want to configure a repeater, please skip to C.

Note

Click Next

B. Configuration for Point to Point Connection

1) The AP Setting

After successfully logging in, configure the other TL-WA5110G by following the steps

below.

2) The Client Setting

Click Finish to exit the Quick Setup

wizard and wait until the AP completes

rebooting automatically. The changes

will take effect after rebooting.

Note Two TL-WA5110G Access Points are needed for this application.

Note You should change the default LAN IP address of the Client from

192.168.1.254 to 192.168.1.X (X can be any number from 1 to 253) to avoid

an IP conflict with the former AP. Here we choose 192.168.1.2 as an example.

Click Next

Select AP

Enter a unique name for your

wireless network; however, choose a

name that is easily remembered by

network users. Here we enter

TP-LINK_88346E as the SSID for

exam

Select your region from the

drop-down list

Click Finish

Click Save at the bottom of this page.

C. Configuration for Repeater

The AP will begin rebooting automatically after clicking Save.

Select Repeater

Click Survey

Click Wireless >Wireless Mode

Note

Click Wireless > Wireless Mode

Select Client

Enter TP-LINK_88346E, the SSID

of the first AP you configured

Click Save

Click Network

Enter 192.168.1.2 in the

IP Address field

Find the BSSID of the remote AP

that you want to repeat, and then

write it down or copy it. Here we

copy the BSSID of ‘TP-LINK’ that

is 00-19-E0-94-51-F4

Enter or paste the BSSID of

the remote AP into the box

under Repeater

This page will then display.

Then click Save at the bottom of this page.

The BSSID is the same as the MAC address.

Note

T1. How do I restore my Router’s configuration to its factory default settings?

T2. What can I do if I forget my password?

1) Restore the AP’s configuration to its factory default settings. If you don’t know

how to do that, please refer to previous section T1;

2) Use the default user name and password: admin, admin;

3) Try to reconfigure your AP by following the instructions of this QIG.

T3. How can I do if I want to configure the High Power?

1) Click “Wireless > Basic Settings” to enter Wireless Settings page.

2) If you want to use the high power mode, check the box before “Enable High

Power Mode” and options available of the Power list will be 26dBm Max,

23dBm, 20dBm, 17dBm, 14dBm Min.

3) If you don’t want to use the high power mode, deselect the box before “Enable

High Power Mode” and options available of the Power list will be Max, 1/2, 1/4,

1/8, Min.

4) Click Save to save the changes.

T4. What can I do if I cannot access the web-based configuration page?

1) Configure your computer’s IP Address.

With the AP powered on, press and

hold the RESET button on the rear

panel for 8 to 10 seconds before

releasin

it.

Once the AP is reset, the current configuration settings will be lost and you

will need to reconfigure the router.

Hold it in for 8 to

10 seconds

For Windows XP OS

Go to Start > Control Panel,

you will then see the

following page.

Click Network and Internet

Connections

Click Properties

Right-click Local

Area Connection

Click Network

Connections

Select Use the following

IP address

Enter the 192.168.1.100 into the

IP address field, 255.255.255.0

into the Subnet mask field

Enter the DNS server address

provided by your ISP or network

administrator

Select Use the following

DNS server addresses

Double-click Internet

Protocol

(

TCP/IP

)

Click OK

Altri manuali per TL-WA5110G

Indice

Altri manuali TP-Link Punto di accesso wireless

TP-Link

TP-Link TL-WA850RE Manuale utente

TP-Link

TP-Link TL-WA7210N Manuale del proprietario

TP-Link

TP-Link 54Mbps Wireless Access Point TL-WA501G Manuale utente

TP-Link

TP-Link TL-WA701ND Manuale utente

TP-Link

TP-Link TL-WA500G Manuale utente

TP-Link

TP-Link TL-WA1201 Manuale utente

TP-Link

TP-Link TL-WA801ND Manuale utente

TP-Link

TP-Link 54Mbps Wireless Access Point TL-WA501G Manuale utente

TP-Link

TP-Link Auranet EAP120 Manuale utente

TP-Link

TP-Link Pharos CPE210 Manuale utente

TP-Link

TP-Link Omada EAP225-Wall Manuale utente

TP-Link

TP-Link AURANET CAP300-Outdoor Manuale utente

TP-Link

TP-Link AP9635 Manuale utente

TP-Link

TP-Link Auranet EAP120 Manuale utente

TP-Link

TP-Link TL-WA901ND Manuale utente

TP-Link

TP-Link Omada EAP245 Manuale utente

TP-Link

TP-Link Auranet EAP110 Manuale utente

TP-Link

TP-Link Auranet EAP110 Manuale utente

TP-Link

TP-Link TL-WA5210G Manuale utente

TP-Link

TP-Link Auranet EAP110 Manuale utente

TP-Link

TP-Link Omada EAP225 Manuale utente

TP-Link

TP-Link Omada EAP650 Manuale utente

TP-Link

TP-Link EAP265 Manuale utente

TP-Link

TP-Link Omada EAP620 HD V2 Manuale utente

Manuali Punto di accesso wireless popolari di altre marche

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuale utente

Ubiquiti

Ubiquiti NanoStation NSM2 Manuale utente

Cisco

Cisco Aironet 1550 Series Manuale utente

Aruba

Aruba IAP-335 Manuale utente

Advantek Networks

Advantek Networks AWN-AP-54MR Manuale utente

IP-COM

IP-COM AP355 Manuale utente

Buffalo

Buffalo AirStation WLA-L11G Manuale utente

EnGenius

EnGenius EnStationACv2 Manuale utente

D-Link

D-Link DAP-3662 Manuale utente

xG Technology

xG Technology xMax CN1300 Manuale utente

Widelink

Widelink ezWave WAP-1100 Series Manuale utente

Edimax

Edimax CAP1200 Manuale utente

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuale utente

Aruba

Aruba AP-203R Manuale utente

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuale utente

CreatComm

CreatComm TB5F Manuale utente

SineDigital

SineDigital MW-1500AP(H) Manuale utente

Draytek

Draytek VIGORAP 902 Manuale utente