Trane Technologies BAYKSKT267 Istruzioni per il montaggio
HAZARDOUS VOLTAGE - DISCONNECT POWER BEFORE SERVICING
WARNING:
ALL phases of this installation must comply with NATIONAL, STATE AND LOCAL CODES
IMPORTANT —This Document is customer property and is to remain with this unit. Please return to service information pack
upon completion of work.
Installer’s Guide
NOTE: THIS KIT AND EXTERNAL ENCLOSURE BOX04083 MUST BE PURCHASED TOGETHER UNLESS BAYLOAM108
(LOW AMBIENT KIT) IS ALSO BEING INSTALLED ON UNIT.
Start Control Kit
BAYKSKT267
88-MACC014-1C-EN
START CONTROL KIT CONTENTS:
--------------------------------------------------------------------------
No. Qty. Description
1 1 Start Capacitor
2 1 Relay
3 1 Capacitor Strap
4 1 #6-20 Self-drilling Screw
5 2 #10-16 Self-drilling Screw
6 1 Installer’s Guide
7 1 Warning Label
INSPECTION:
Check carefully for any shipping damage. This must be
reported to and claims made against the transportation company
immediately. Any missing parts should be reported to your
supplier at once and replaced with authorized parts only.
INSTALLATION:
Mounting Start Control Kit Components
1. Be certain power to unit is DISCONNECTED.
2. Remove cover panel on unit control box compartment.
3. Locate the unit control box bottom and mark the hole
position in the approximate location as shown in Figure 1.
4. Using a .875" drill bit, drill a hole through the unit con-
trol box bottom. Make sure not to damage any wiring
or components. Deburr the drilled hole and remove any
unwanted material.
New Ø .875” hole
FIGURE 1
2 88-MACC014-1C-EN
Installer’s Guide
Relay
Orient and form
Capacitor Mounting
Strap
Assemble Star
t
Capacitor with
label out
#10-16 Screw (x 2)
#6-20 Screw
FIGURE 2 FIGURE 3
5. Open Start Control Kit and remove kit contents.
6. If the enclosure has not previously been installed with
BAYLOAM108 (low ambient kit), proceed to step 7. If the
enclosure has already been installed, skip to step 10.
7. Mount the enclosure with field-provided screws to the
side of the house or structure such that the distance
between the unit control box and the external enclosure is
minimized as much as possible.
NOTE: Due to the multitude of potential structure materi-
als, the screws needed for mounting enclosure to
structure will be field-provided.
8. Secure the mounting plate inside of box using four of the
enclosure provided screws as shown in Figure 2.
9. Knock or drill out one of the enclosure cutouts to route
the 1/2" conduit.
10. Using the #6-20 and #10-16 self-drilling screws provided,
secure the relay and capacitor in the approximate loca-
tions as shown in Figure 3.
Mounting Plate
Screw (x 4)
Installer’s Guide
Wiring Start Control Kit Components
1. Connect the color coded start control wires with quick
connect ¼” flag terminals to the contactor and capacitor
as illustrated in Figure 4.
2. Route all three high voltage wires through field-supplied
½” conduit.
3. Secure field-supplied liquid tight conduit fittings at
enclosure and control box entries.
4. Attach the warning label to the enclosure cover. This
label provides a warning for hazardous voltage.
5. Re-connect power, which was disconnected in Step 1.
FIGURE 4
Red Wire:
Start Capacitor
to MS-T1
Orange Wire:
CSR 2 to Run
Capacitor -
H Terminal
Black/Blue
Wire: CSR 5
to MS-T2
Brown Wire:
Start Capacitor
to CSR 1
MS-T1
MS-T2
About Trane and American Standard Heating and Air Conditioning
Trane and American Standard create comfortable, energy efficient indoor environments for residential applications.
For more information, please visit www.trane.com or www.americanstandardair.com
The manufacturer has a policy of continuous data improvement and it reserves the right to change design and specifications without notice. We are commit-
ted to using environmentally conscious print practices.
© 2020
88-MACC014-1C-EN 08 Jul 2020
Supersedes 88-MACC014-1B-EN (December 2019)
Altri manuali Trane Technologies Unità di controllo
Manuali Unità di controllo popolari di altre marche
Festo
Festo Compact Performance CP-FB6-E Manuale elenco delle parti
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuale utente
JS Automation
JS Automation MPC3034A Manuale utente
JAUDT
JAUDT SW GII 6406 Series Guida rapida
Spektrum
Spektrum Air Module System Manuale utente
BOC Edwards
BOC Edwards Q Series Manuale utente
