Transcend TS16GCF600 Manuale utente

600X CompactFlash Card

Transcend Information Inc.

V1.0

Description

Dedicated to fulfilling the demanding requirements of

performance-conscious photographers, Transcend

proudly releases its Extreme Plus 600X CompactFlash

cards with Turbo MLC technology. With its amazing

performance,the Transcend 600x CompactFlash

memory card allows the professional photographers

and enthusiasts to get the most from your digital single

lens reflex (DSLR) camera. Users are guaranteed to

makes consecutive shooting and non-stop video

recording and share their digital artwork with the world!

Placement

Dimensions

Features

•CompactFlash Specification Version 4.1 Complaint

•RoHS compliant products

•Single Power Supply: 3.3V

5% or 5V

10%

•Operating Temperature: -25

C to 85

•Storage Temperature: -40

C to 85

•Operating/ Storage Humidity: 5% to 95%

•Operation Modes:



PC Card Memory Mode



PC Card IO Mode



True IDE Mode

•True IDE Mode supports:



Ultra DMA Mode 0 to Ultra DMA Mode 6 (Ultra DMA

mode 5/6 must use Power supply: 3.3V)



MultiWord DMA Mode 0 to MultiWord DMA Mode 4



PIO Mode 0 to PIO Mode 6

•PC Card Mode supports up to Ultra DMA Mode 6

•True IDE mode: Fixed Disk (Standard)

•PC Card Mode: Removable Disk (Standard)

•Durability of Connector: 10,000 times

•

Built-in 15 bit ECC (Error Correction Code) functionality

•Support Global Wear-Leveling to extend product life

•Compliant to CompactFlash, PC Card Mode, and ATA

standards

Power

Consumption

* Maximum value

Product TS8GCF600

TS16GCF600

Standby

2.4mA 2.5mA

Read 222.8mA 232.8mA

Power

Consumption

(DC 3.3V

℃

)

Write 218.1mA 211.5mA

600X CompactFlash Card

Transcend Information Inc.

V1.0

Transcend

600X CompactFlash Card

Transcend Information Inc.

V1.0

Block Diagram

600X CompactFlash Card

Transcend Information Inc.

V1.0

600X CompactFlash Card

Transcend Information Inc.

V1.0

Pin Assignments and Pin Type

PC Card Memory Mode PC Card I/O Mode True IDE Mode

Num

Signal

Name

Type

In, Out Type

Pin Num

Signal

Name

Type

In, Out

Type

Num

Signal

Name

Type

In, Out

Type

1 GND

Ground 1 GND

Ground

1 GND

Ground

2 D03 I/O I1Z, OZ3 2 D03 I/O I1Z, OZ3

2 D03 I/O I1Z, OZ3

3 D04 I/O I1Z, OZ3 3 D04 I/O I1Z, OZ3

3 D04 I/O I1Z, OZ3

4 D05 I/O I1Z, OZ3 4 D05 I/O I1Z, OZ3

4 D05 I/O I1Z, OZ3

5 D06 I/O I1Z, OZ3 5 D06 I/O I1Z, OZ3

5 D06 I/O I1Z, OZ3

6 D07 I/O I1Z, OZ3 6 D07 I/O I1Z, OZ3

6 D07 I/O I1Z, OZ3

7 -CE1 I I3U 7 -CE1 I I3U 7 -CS0 I I3Z

8 A10 I I1Z 8 A10 I I1Z 8 A10

I I1Z

9 -OE I I3U 9 -OE I I3U 9 -ATA SEL

I I3U

A09 I I1Z 10 A09 I I1Z 10 A09

I I1Z

A08 I I1Z 11 A08 I I1Z 11 A08

I I1Z

A07 I I1Z 12 A07 I I1Z 12 A07

I I1Z

VCC

Power 13 VCC

Power

13 VCC

Power

A06 I I1Z 14 A06 I I1Z 14 A06

I I1Z

A05 I I1Z 15 A05 I I1Z 15 A05

I I1Z

A04 I I1Z 16 A04 I I1Z 16 A04

I I1Z

A03 I I1Z 17 A03 I I1Z 17 A03

I I1Z

A02 I I1Z 18 A02 I I1Z 18 A02 I I1Z

A01 I I1Z 19 A01 I I1Z 19 A01 I I1Z

A00 I I1Z 20 A00 I I1Z 20 A00 I I1Z

D00 I/O I1Z, OZ3 21 D00 I/O I1Z, OZ3

21 D00 I/O I1Z, OZ3

D01 I/O I1Z, OZ3 22 D01 I/O I1Z, OZ3

22 D01 I/O I1Z, OZ3

D02 I/O I1Z, OZ3 23 D02 I/O I1Z, OZ3

23 D02 I/O I1Z, OZ3

WP O OT3 24 -IOIS16

O OT3 24 -IOCS16

O ON3

-CD2 O Ground 25 -CD2 O Ground

25 -CD2 O Ground

-CD1 O Ground 26 -CD1 O Ground

26 -CD1 O Ground

D11

I/O

I1Z, OZ3 27 D11

I/O

I1Z, OZ3

27 D11

I/O

I1Z, OZ3

D121 I/O

I1Z, OZ3 28 D12

I/O

I1Z, OZ3

28 D12

I/O

I1Z, OZ3

D13

I/O

I1Z, OZ3 29 D13

I/O

I1Z, OZ3

29 D13

I/O

I1Z, OZ3

D14

I/O

I1Z, OZ3 30 D14

I/O

I1Z, OZ3

30 D14

I/O

I1Z, OZ3

D15

I/O

I1Z, OZ3 31 D15

I/O

I1Z, OZ3

31 D15

I/O

I1Z, OZ3

-CE2

I I3U 32 -CE2

I I3U 32 -CS1

I I3Z

-VS1 O Ground 33 -VS1 O Ground

33 -VS1 O Ground

600X CompactFlash Card

Transcend Information Inc.

V1.0

PC Card Memory Mode PC Card I/O Mode True IDE Mode

Num

Signal Name

Type

In, Out

Type

Num

Signal Name

Type

In, Out

Type

Num

Signal Name

Type

In, Out

Type

-HIOE

HSTROBE

-HIOE

HSTROBE

HDMARDY

I I3U 34

-HIOE

HSTROBE

-HDMARDY

I I3U 34

-HDMARDY

I I3Z

-IOWR -IOWR -IOWR

STOP

10,11

I I3U 35

STOP

10,11

I I3U 35

STOP

8,9

I I3Z

-WE I I3U 36 -WE I I3U 36 -WE

I I3U

READY O OT1 37 -IREQ O OT1 37 INTRQ O OZ1

VCC Power

38 VCC Power

-CSEL

I I2Z 39 -CSEL

I I2Z 39 -CSEL I I2U

-VS2 O OPEN

40 -VS2 O OPEN

RESET I I2Z 41 RESET I I2Z 41 -RESET I I2Z

-WAIT -WAIT IORDY

ON1

-DDMARDY

DSTROBE

O OT1 42

DSTROBE

O OT1 42

DSTROBE

O OT1

-INPACK -INPACK

-DMARQ

O OT1 43

-DMARQ

O OT1 43 DMARQ O OZ1

-REG I I3U 44 -REG

-DMACK

DMACK

I I3U 44 -DMACK

I I3U

BVD2 O OT1 45 -SPKR O OT1 45 -DASP I/O I1U, ON1

BVD1 O OT1 46 -STSCHG O OT1 46 -PDIAG I/O I1U, ON1

D08

I/O

I1Z,

OZ3 47 D08

I/O

I1Z,

OZ3 47 D08

I/O

I1Z, OZ3

D09

I/O

I1Z,

OZ3 48 D09

I/O

I1Z,

OZ3 48 D09

I/O

I1Z, OZ3

D10

I/O

I1Z,

OZ3 49 D10

I/O

I1Z,

OZ3 49 D10

I/O

I1Z, OZ3

GND Ground

50 GND Ground

Note: 1) These signals are required only for 16 bit accesses and not required when installed in 8 bit systems. Devices should allow for 3-state

signals not to consume current.

2) The signal should be grounded by the host.

3) The signal should be tied to VCC by the host.

4) The mode is required for CompactFlash Storage Cards.

5) The -CSEL signal is ignored by the card in PC Card modes. However, because it is not pulled upon the card in these modes,

it should not be left floating by the host in PC Card modes. In these modes, the pin should be connected by the host to PC

Card A25 or grounded by the host.

6) If DMA operations are not used, the signal should be held high or tied to VCC by the host. For proper operation in older hosts: while DMA

operations are not active, the card shall ignore this signal,including a floating condition

7) Signal usage in True IDE Mode except when Ultra DMA mode protocol is active.

8) Signal usage in True IDE Mode when Ultra DMA mode protocol DMA Write is active.

9) Signal usage in True IDE Mode when Ultra DMA mode protocol DMA Read is active.

10) Signal usage in PC Card I/O and Memory Mode when Ultra DMA mode protocol DMA Write is active.

11) Signal usage in PC Card I/O and Memory Mode when Ultra DMA mode protocol DMA Read is active.

12) Signal usage in PC Card I/O and Memory Mode when Ultra DMA protocol is active.

600X CompactFlash Card

Transcend Information Inc.

V1.0



Input Leakage Current

Note: In Table 1 below, x refers to the characteristics described in table 2. For example, I1U indicates a pull-up resistor with a type 1

input characteristic.

Table 1: Input Leakage Current

Type Parameter Symbol

Conditions MIN

TYP

MAX

Units

IxZ Input Leakage Current

IL Vih = Vcc / Vil = Gnd

-1

1 µA

IxU Pull-Up Resistor RPU1 Vcc = 5.0V 50k

500k

Ohm

IxD Pull-Down Resistor RPD1 Vcc = 5.0V 50k

500k

Ohm

Note: The minimum pull-up resistor resistance meets the PCMCIA PC Card specification of 10k ohms but is intentionally higher in the

CompactFlash Specification to reduce power use.



Input Characteristics

Table 2: Input Characteristics

MIN

TYP MAX

MIN

TYP MAX

Type

Parameter Symbol

VCC = 3.3 V VCC = 5.0 V

Units

1 Input Voltage

CMOS

Vih

Vil 2.4

0.6 4.0

0.8 Volts

2 Input Voltage

CMOS

Vih

Vil 1.5

0.6 2.0

0.8 Volts

Input Voltage

CMOS Schmitt

Trigger

Vth

Vtl

1.8

1.0

2.8

2.0

Volts

Notes: 1) The host provides a logic output high voltage for a CMOS load of .9 x VCC. For a 5 volt product, this translates to .9 x

4.5 = 4.05 volts minimum Voh.



Output Drive Type

Note: In Table 3 below, x refers to the characteristics described in Table 4. For example, OT3 refers to Totem pole output with a type

3 output drive characteristic.

Table 3: Output Drive Type

Type Output Type Valid Conditions

OTx Totempole Ioh & Iol

OZx Tri-State N-P Channel Ioh & Iol

OPx P-Channel Only Ioh Only

ONx N-Channel Only Iol Only

600X CompactFlash Card

Transcend Information Inc.

V1.0



Output Drive Characteristics

Table 4: Output Drive Characteristics

Type

Parameter Symbol Conditions MIN TYP MAX Units

1 Output Voltage

Voh

Vol

Ioh = -4 mA

Iol = 4 mA

Vcc

-0.8V

Gnd

+0.4V

Volts

2 Output Voltage

Voh

Vol

Ioh = -4 mA

Iol = 4 mA

Vcc

-0.8V

Gnd

+0.4V

Volts

3 Output Voltage

Voh

Vol

Ioh = -4 mA

Iol = 4 mA

Vcc

-0.8V

Gnd

+0.4V

Volts

X Tri-State Leakage

Current Ioz Vol = Gnd

Voh = Vcc -10

10 µA

600X CompactFlash Card

Transcend Information Inc.

V1.0

Signal Description

Signal Name

Dir.

Description

A10 – A00

(PC Card Memory Mode)

A10 – A00

(PC Card I/O Mode)

A02 - A00

(True IDE Mode)

8,10,11,12,

14,15,16,17,

18,19,20

These address lines along with the -REG signal are used to

select the following:

The I/O port address registers within the CompactFlash Storage Card , the

memory mapped port address registers within the CompactFlash Storage Card,

a byte in the card's information structure and its

configuration control and status

registers.

This signal is the same as the PC Card Memory Mode signal.

In True IDE Mode, only A[02:00] are used to select the one of eight registers

in the Task File, the remaining address lines should be grounded by the

host.

BVD1

(PC Card Memory Mode)

-STSCHG

(PC Card I/O Mode)

Status Changed

-PDIAG

(True IDE Mode)

I/O

46 This signal is asserted high, as BVD1 is not supported.

This signal is asserted low to alert the host to changes in the

READY and Write

Protect states, while the I/O interface is configured. Its use is controlled by the

Card Config and Status Register.

In the True IDE Mode, this input / output is the Pass Diagnostic signal in the

Master / Slave handshake protocol.

BVD2

(PC Card Memory Mode)

-SPKR

(PC Card I/O Mode)

-DASP

(True IDE Mode)

I/O

45 This signal is asserted high, as BVD2 is not supported.

This line is the Binary Audio output from the card. If the Card does not support

the Binary Audio function, this line should be held negated.

In the True IDE Mode, this input/output is the Disk Active/Slave

Present signal in

the Master/Slave handshake protocol.

-CD1, -CD2

(PC Card Memory Mode)

-CD1, -CD2

(PC Card I/O Mode)

-CD1, -CD2

(True IDE Mode)

26,25 These Card Detect pins are connected to ground on the

CompactFlash Storage

Card. They are used by the host to determine that the CompactFlash Storage

Card is fully inserted into its socket.

This signal is the same for all modes.

600X CompactFlash Card

Transcend Information Inc.

V1.0

Signal Name

Dir.

Description

-CE1, -CE2

(PC Card Memory Mode)

Card Enable

-CE1, -CE2

(PC Card I/O Mode)

Card Enable

-CS0, -CS1

(True IDE Mode)

7,32 These input signals are used both to select the card and to indi

cate to the card

whether a byte or a word operation is being performed. -CE2 always accesses

the odd byte of the word.-CE1 accesses the even byte or the Odd byte of the

word depending on A0 and -CE2. A multiplexing scheme based on A0,-CE1,

-CE2 allows 8 bit hosts to access all data on D0-D7. See Table 27, Table 29,

Table 31, Table 35, Table 36 and Table 37.

This signal is the same as the PC Card Memory Mode signal.

In the True IDE Mode, -CS0 is the address range select for the task file

registers while -CS1 is used to select the Alternate Status Register and the

Device Control Register.

While –DMACK is asserted, -CS0 and –CS1 shall be held negated and the

width of the transfers shall be 16 bits.

-CSEL

(PC Card Memory Mode)

-CSEL

(PC Card I/O Mode)

-CSEL

(True IDE Mode)

39 This signal is not used for this mode, but should be connected by

the host to PC

Card A25 or grounded by the host.

This signal is not used for this mode, but should be connected by

the host to PC

Card A25 or grounded by the host.

This internally pulled up signal is used to configure this device as

a Master or a

Slave when configured in the True IDE Mode.

When this pin is grounded, this device is configured as a Master.

When the pin is open, this device is configured as a Slave.

D15 - D00

(PC Card Memory Mode)

D15 - D00

(PC Card I/O Mode)

D15 - D00

(True IDE Mode)

I/O

31,30,29,28,

27,49,48,47,

6,5,4,3,2,

23, 22, 21

These lines carry the Data, Commands and Status information

between the host

and the controller. D00 is the LSB of the Even

Byte of the Word. D08 is the LSB

of the Odd Byte of the Word.

This signal is the same as the PC Card Memory Mode signal.

In True IDE Mode, all Task File operations occur in byte mode

on the low order

bus D[7:0] while all data transfers are 16 bit using D[15:0].

GND

(PC Card Memory Mode)

GND

(PC Card I/O Mode)

GND

(True IDE Mode)

1,50 Ground.

This signal is the same for all modes.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Transcend Magazzinaggio

Transcend

Transcend miniSDHC Card Series Manuale utente

Transcend

Transcend TS120GSJ25T Manuale utente

Transcend

Transcend MMC Series Istruzioni per il montaggio

Transcend

Transcend JetFlash 220 Manuale utente

Transcend

Transcend ExpressCard SSD34E Manuale utente

Transcend

Transcend StoreJet 25 mobile Manuale utente

Transcend

Transcend StoreJet 25M 640GB Manuale utente

Transcend

Transcend TS4GSDOM22H Manuale

Transcend

Transcend CompactFlash TS8GCF266 Istruzioni per il montaggio

Transcend

Transcend JetDrive SSD Upgrade Kit Manuale utente

Transcend

Transcend Secure Digital Card TS2GSD133 Manuale utente

Transcend

Transcend JetFlash V20 Manuale utente

Transcend

Transcend StoreJet 25H2 Manuale utente

Transcend

Transcend StoreJet 18 mobile Manuale utente

Transcend

Transcend JetFlash V33p Manuale utente

Transcend

Transcend JetFlash 160 Manuale utente

Transcend

Transcend SSD18M Manuale utente

Transcend

Transcend TS2GIFD25 Manuale

Transcend

Transcend TS250GSJ25M-R Manuale utente

Transcend

Transcend TS128M~8GJF2A Manuale utente

Transcend

Transcend JetFlash 820 Manuale utente

Transcend

Transcend TS1~2GUSD-S3 Manuale

Transcend

Transcend SD Manuale utente

Transcend

Transcend TS64GSSD10-M Manuale utente

Manuali Magazzinaggio popolari di altre marche

QNAP

QNAP TS 32PXU Series Manuale utente

LaCie

LaCie RUGGED RAID Manuale utente

Freecom

Freecom CLS DOCK Manuale utente

PNY

PNY Attache P-FD64MBATT3 Manuale utente

HP StorageWorks MSL2024 Manuale utente

OLT

OLT 6x6 Maximizer Manuale utente

LaCie

LaCie RUGGED MINI Manuale utente

Thunderbolt

Thunderbolt 600 Manuale utente

Panasonic

Panasonic LB-DH8 series Manuale

Intel

Intel RAID High Availability Manuale utente

LaCie

LaCie 12big Thunderbolt 3 Manuale utente

Spectra Logic

Spectra Logic T-Series Spectra T50e Manuale utente

Panasonic

Panasonic LKM-F931-1 Manuale utente

Tabernus

Tabernus Enterprise Erase E2400 Manuale utente

Rocstor

Rocstor COMMANDER 3F series Manuale utente

HP P9000 Manuale utente

Western Digital

Western Digital Ultrastar Data60 Manuale utente

Dell

Dell PowerVault MD3600f Series Manuale utente