Transition Networks STACKMASTER TR SMHB-TR-16 Manuale utente

StackMaster TR

Active Retiming Managed Hub

SMHB-TR-16

#7361.C

™

CAUTION: RJ connectors are NOT INTENDED FOR

CONNECTION TO THE PUBLIC TELEPHONE NETWORK.

Failure to observe this caution could result in damage to the

public telephone network.

Compliance Information

UL Listed

C-UL Listed (Canada)

CISPR/EN55022 Class A

FCC Regulations

This equipment has been tested and found to comply with the limits for a class

A digital device, pursuant to part 15 of the FCC rules. These limits are

designed to provide reasonable protection against harmful interference when

the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference, in which case the user

will be required to correct the interference at the user’s own expense.

Canadian Regulations

This digital apparatus does not exceed the Class A limits for radio noise for

digital apparatus set out on the radio interference regulations of the Canadian

Department of Communications.

European Regulations

Warning

This is a Class A product. In a domestic environment this product may cause

radio interference in which case the user may be required to take adequate

measures.

form or by any means – graphic, electronic, or mechanical – without written

permission from TRANSITION Networks Inc.

Trademark Notice

All registered trademarks and trademarks are the property of their respective

owners.

Der Anschluss dieses Gerätes an ein öffentlickes

Telekommunikationsnetz in den EG-Mitgliedstaaten verstösst gegen die

jeweligen einzelstaatlichen Gesetze zur Anwendung der Richtlinie

91/263/EWG zur Angleichung der Rechtsvorschriften der

Mitgliedstaaten über Telekommunikationsendeinrichtungen

einschliesslich der gegenseitigen Anerkennung ihrer Konformität.

Table of Contents

Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii

1. INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–1

2. SITE PLANNING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–1

2.1 Site Considerations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–1

2.2 Network Parameters Data Sheets . . . . . . . . . . . . . . . . . . . . . . . . . . . .2–2

TCP/IP Network Parameters Data Sheet . . . . . . . . . . . . . . . . . . . . 2-2

SNMP Network Parameters Data Sheet. . . . . . . . . . . . . . . . . . . . . 2-3

Serial Port Parameters Data Sheet. . . . . . . . . . . . . . . . . . . . . . . . . 2-4

3. INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3–1

3.1 Unpacking StackMaster™TR Equipment . . . . . . . . . . . . . . . . . . . . . . .3–1

3.2 Stacking Units in Rack or on Table . . . . . . . . . . . . . . . . . . . . . . . . . . .3–2

3.2.1 Standard 19-Inch Rack Installation . . . . . . . . . . . . . . . . . . . . . . .3–2

3.2.2 Table-Top Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3–3

3.3 Cascading StackMaster™TR Units . . . . . . . . . . . . . . . . . . . . . . . . . . .3–4

3.4 Connecting StackMaster™TR to Token Ring Network . . . . . . . . . . . .3–5

3.5 Connecting Units to Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3–6

3.6 Resetting StackMaster™TR Stack . . . . . . . . . . . . . . . . . . . . . . . . . . . .3–7

Managed Stack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3–7

Unmanaged Stack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3–7

3.7 Optionally Configuring SNMP Management at Attached Terminal . .3–8

3.7.1 Connecting to ASCII Terminal . . . . . . . . . . . . . . . . . . . . . . . . . .3–8

3.7.2 Bringing Up Configuration Software . . . . . . . . . . . . . . . . . . . . .3–9

3.7.4 Setting Network and SNMP Parameters . . . . . . . . . . . . . . . . . .3–10

Network Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3–10

SNMP Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3–11

3.7.3 Resetting the StackMaster™TR . . . . . . . . . . . . . . . . . . . . . . . . .3–12

4. OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4–1

4.1 Power On/Power Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4–1

5. MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5–1

5.1 Fault Isolation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5–1

5.2 Recovery Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5–4

Resetting the StackMaster™TR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-4

User’s Guide

5.3 Replacement Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5–5

Replacing StackMasterTR Unit Fuses . . . . . . . . . . . . . . . . . . . . . . . . .5–5

5.4 StackMasterTR Field Upgrades . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5–6

Installing SNMP Management Board . . . . . . . . . . . . . . . . . . . . . . . . . .5–6

5.5 Software Upgrades . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5–9

Software Upgrade at Attached ASCII Terminal . . . . . . . . . . . . . . . . . .5–9

Obtaining Updated StackMaster™TR Software. . . . . . . . . . . . . . .5–9

Connecting to ASCII Terminal . . . . . . . . . . . . . . . . . . . . . . . . . . .5–9

Resetting the StackMasterTR . . . . . . . . . . . . . . . . . . . . . . . . . . . .5–10

Transferring the File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5–10

ii StackMasterTR

Preface

This guide is intended for the system or network administrator responsible

for installing, configuring, using, and maintaining a Transition Engineering

StackMaster™TR. A working knowledge of local area network (LAN) oper-

ations, including familiarity with communications protocols used on inter-

connected LANs, is assumed.

iii

User’s Guide

1. Introduction

The TRANSITION Networks 16-Port StackMaster™TR Active Retiming

Managed Hubs are designed for building SNMP managed token ring LANs

using twisted pair cable.

The StackMaster™TR Managed Hub:

• Complies with current IEEE 802.5 token ring standards to ensure

interoperability

• Supports external SNMP network management

• Provides sixteen RJ-45 lobe ports support both STP and UTP

• Provides active signal retiming and regeneration on a per port basis

maximizes lobe and RI/RO cable runs

• Supports Category 3, 4 or 5 UTP/STP and IBM Type 1 Cable

• Allows 4 or 16 Mbps operation

• Allows RI/RO connection to both “active hubs” and “passive hubs”

• Delivers fault-tolerant, automatic ring wrap capability at RI/RO

• Provides Zero Delay Lockout, automatic lockout of station configured

at wrong speed

• Installed as standalone or rackmount in a standard 19” rackmount

frame.

• Provides serial port connection for Out of Band management.

NOTE: The StackMaster™TR 16-Port Hub is designed to support an

Active Retime environment with HOT SWAP capability. An active hub

can be added or removed without bringing the network down.

USER’S GUIDE 1-1

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Lobe Ports

Active Retiming Managed Hub

Insert Normal

Power Ring Out

4 Mbps P

16 Mbps

Reset

™

16 Port StackMaster TR

ZDL

OFF

123 4

5678

Expansion Card

Indicators

Enable Status

Ring In

networks

TRANSITION

Connectors

Ring In/Ring Out Connector

An RJ-45 Ring In connector and an RJ-45 Ring Out connector are

provided at the front of the 16-Port StackMaster™TR Active Retiming

Managed Hub.

Lobe Connectors

Sixteen (16) RJ-45 lobe connectors are provided at the front of the 16-Port

StackMaster™TR Active Retiming Managed Hub.

1-2 StackMaster™TR

Ring In R ing Out

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Lobe Ports

Active Retiming Managed Hub

Insert Normal

Power Ring Out

4 Mbps P

16 Mbps

Reset

™

16 Port StackMaster TR

ZDL

OFF

123 4

5678

Expansion Card

Indicators

Enable Status

Ring In

networks

TRANSITION

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Lobe Ports

Active Retiming Managed Hub

Insert Normal

Power Ring Out

4 Mbps P

16 Mbps

Reset

™

16 Port StackMaster TR

ZDL

OFF

123 4

5678

Expansion Card

Indicators

Enable Status

Ring In

networks

TRANSITION

Connectors at Back

A serial port connector for SNMP management and maintenance, two (2)

Cascade (bus) connectors, and a power connector are provided at the

back of the StackMaster™TR 16-Port.

NOTE: The AUX connector is intended for future development.

11..IINNTTRROODDUUCCTTIIOONN

USER’S GUIDE 1-3

Caution : For continued protection against risk of fire, replace only

with same type and rating of fuse : 250V 2A.

Caution : Disconnect power before replacing fuse.

ATTENTION: Couper le courant avant de replacer le fusible.

2A, 250V

Input Power: 100-240 V

50/60 Hz

0.5 A

Model#: SMHB-TR-16

Mpls, MN 55344

Cascade Connectors

Serial AUX Achtung!: Zum anhaltenden Schutz vor Feurgefahr, Sicherung nur

mit einer gleichnamiger Stromstarke und Spannung

ersetzen: 250V, 2A

Achtung!: Stromleitung ausschalten bevor Sicherung ersetzen!

networks

TRANSITION

Serial

Cascade (Bus) Connectors

Power Connector

Indicators

Power LED

When the StackMaster™TR 16-Port Unit is powered, the Power indicator

is illuminated.

Insert/Normal LEDs

The Insert LED (above the Ring In port) is illuminated if the

StackMaster™TR 16-Port RI port is connected to the RO port of a hub.

NOTE: When the RI switch is in the passive position, the LED always is

ON, indicating that the RI port is configured in the passive mode.

The Normal LED (above the Ring Out port) is illuminated if the

StackMaster™TR 16-Port RO port is connected to the RI port of a hub

which is powered.

NOTE: When the RO switch is in the passive position, the LED always is

ON, indicating that the RO port is configured in the passive mode.

1-4 StackMaster™TR

Power

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Lobe Ports

Active Retiming Managed Hub

Insert Normal

Power

Ring Out

4 Mbps P

16 Mbps

Reset

™

16 Port StackMaster TR

ZDL

OFF

123 4

5678

Expansion Card

Indicators

Enable Status

Ring In

networks

TRANSITION

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Lobe Ports

Active Retiming Managed Hub

Insert Normal

Power Ring Out

4 Mbps P

16 Mbps

Reset

™

16 Port StackMaster TR

ZDL

OFF

123 4

5678

Expansion Card

Indicators

Enable Status

Ring In

networks

TRANSITION

Normal

Insert

Indice

Altri manuali Transition Networks Interruttore

Transition Networks

Transition Networks SM24DPa Manuale utente

Transition Networks

Transition Networks E-TBT-HB-0402 Manuale utente

Transition Networks

Transition Networks STACKMASTER TX12 Manuale utente

Transition Networks

Transition Networks SISPM1040-362-LRT Manuale utente

Transition Networks

Transition Networks SISTF101X-241-LRT Manuale utente

Transition Networks

Transition Networks SM TAT4X Series Manuale utente

Transition Networks

Transition Networks SM8TAT2SA Manuale di istruzioni

Transition Networks

Transition Networks SISTF10xx-130-LR(T) Manuale utente

Transition Networks

Transition Networks SISPM1040-3-L Series Manuale utente

Transition Networks

Transition Networks SM12DP2XA Manuale utente

Transition Networks

Transition Networks SISPM1040-582-LRT Manuale utente

Transition Networks

Transition Networks SISTP1040-382B-LRT Manuale utente

Transition Networks

Transition Networks SISTG1040-242-LRT Manuale utente

Transition Networks

Transition Networks SISPM1040-3 L Series Manuale utente

Transition Networks

Transition Networks SM4T4DPA Manuale utente

Transition Networks

Transition Networks SESPM1040-541-LT Series Manuale utente

Transition Networks

Transition Networks SM Series Manuale utente

Transition Networks

Transition Networks SISPM1040-3166-L Manuale utente

Transition Networks

Transition Networks SISPM1040-582-LRT Manuale utente

Transition Networks

Transition Networks SM24TAT2DPA Manuale utente

Transition Networks

Transition Networks SISGM1040-184D-LRT Manuale utente

Transition Networks

Transition Networks SM24T6DPA Manuale utente

Transition Networks

Transition Networks SISTM1040-262D-LRT-B Istruzioni operative e di manutenzione

Transition Networks

Transition Networks SISPM1040-582-LRT Manuale utente

Manuali Interruttore popolari di altre marche

URC

URC Total Control MFS-8 Manuale utente

Azbil

Azbil HPQ-D11 Manuale utente

Sony

Sony DFS-900M Manuale utente

SICK

SICK i17S Manuale utente

F&F

F&F SZR-277 Manuale utente

Shure

Shure UAMS/BK Manuale utente

Dräger

Dräger X-zone Switch Off Manuale utente

Asco

Asco Joucomatic 349 Series Manuale utente

BT Mini Hub Manuale utente

D-Link

D-Link DES-1226G Manuale utente

Johnson Controls

Johnson Controls FS80-C Manuale utente

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuale utente

MicroNet

MicroNet SP1200A Manuale utente

Ruijie

Ruijie RG-PF2920 Series Manuale di installazione e funzionamento

Altinex

Altinex DA1914SX Manuale utente

MiLAN

MiLAN MIL-SM2401M Manuale utente

RJM

RJM MASTERMIND PBC/6X Manuale utente

Atlas

Atlas MMK-KVM8 Manuale utente