TRENDnet TE-4010 Guida utente

The information contains in this file is a startup guide for using the

TE-4010 with TRENDnet-View ver. 1.1.

Before you begin, make sure you have the following described environment:

o A PC with a network card installed and properly configured (IRQ and I/O

base address are set). We use TE-16XP/CT, but you can use any NE-2000

compatible cards.

o Windows ver. 3.1 is properly installed on the PC's hard drive.

o The PC is physically connected through a RJ-45 cable with TE-4010. It does

not matter which port is connected to.

o No network software (or driver) is loaded in either CONFIG.SYS and

AUTOEXEC.BAT files. A "clean boot" is preferred.

o Need two pieces of 25-pin serial cable and make the connection from hub's

OUT-OF-BAND management port -> serial cable -> null modem (provided with

TE-4010) -> serial cable -> PC's com1 or com2 port.

1. Start Windows 3.1.

2. Run TERMINAL program in the ACCESSORIES Group.

3. Make sure you have the following configurations:

o Full duplex

o Asynchronous communication

o Data: 8 bit

o Stop bits: 1

o Parity: none

o Baud rate: 9600

o COM1 or COM2 port

4. Press enter several time to go into the setup menu described on page 25

of the TE-4010's manual. Do not type any password.

5. Record the Hub IP Address. For example, 192.132.65.36. You need the IP

address for the TRENDnet-View software. We will use this number for this

example setup procedure.

6. Exit the setup program by pressing ESC key.

7. Exit the TERMINAL program without saving the current configuration. You

are now ready to load TRENDnet-View software. You can disconnect the

serial cable and the null modem.

8. Load TRENDnet-View disk in the floppy disk drive.

9. From program manager, select Run... in the File menu. A dialog box

appears.

10. Type "A:INSTALL" (do not type " ") and click the OK button.

11. In the TRENDnet-View Configuration dialog box, modify the following

information where appropriate:

o IP Address: 192.132.65.xxx xxx, leave it at default

o Gateway IP Address: 192.132.65.xxx xxx, leave it at default

o Subnet Mask: 255.255.255.0

o Network card: NE-2000

o IRQ Number: xx xx, setting for the network card

o I/O Port: xx xx, setting for the network card

12. Type in your password for any future modification of the above settings.

Do not exit from Windows 3.1.

13. Load the TE-4010 SNMP Module disk in the floppy disk drive. The diskette

is included with TE-4010.

14. From program manager, select Run... in the File menu. A dialog box

appears.

15. Type "A:INSTALL" (do not type " ") and click the OK button.

16. The installation is automatic. All files will be copied to where

TRENDnet-View is installed.

17. Exit Windows to DOS prompt.

18. Change directory to where TRENDnet-View is installed. For example,

CD\TRENDNET.

19. Run MANAGER.BAT and it will bring up Windows 3.1 automatically.

20. Run TRENDnet-View by double clicking the TRENDnet-View In-band icon in

TRENDnet-View group.

21. You must place a TE-4010 software module in order for TE-4010 to be seen

by the TRENDnet-View software. Click once on the leftmost button in

the speed button bar. A Device window appears on the upper right corner

on the screen. Move the mouse over the TE-4010 icon and click on it to

select.

22. Move your mouse to the client area of the TRENDnet-View, notice your

mouse cursor changes from a pointer to a stamp. Click the mouse once and

a TE-4010 icon is placed on the client area area. Assign a name for this

hub and supply the IP Address for this hub (For example, 192.132.65.36).

Ignore all other entries. Close the dialog box.

23. Wait couple seconds and the hub's name (beneath the icon) will turn from

blue to green. Double-click the icon and you will see TE-4010 panel on

the screen. You are ready to manage your TE-4010!

Our current version of TRENDnet-View does not run with any network software

installed on the same machine. For example, Windows for Workgroups 3.1/3.11,

Novell Netware 2.x, 3.x, 4.x,....etc. Therefore, do not load any network

software (or network driver) before go into TRENDnet-View.

You must run MANAGER.BAT from DOS prompt before go into TRENDnet-View

software (in-band or out-of-band). MANAGER.BAT loads Windows 3.1

automatically.

Indice

Altri manuali TRENDnet Router di rete

TRENDnet

TRENDnet TEW-691GR Manuale utente

TRENDnet

TRENDnet TW100-BRV324 Manuale utente

TRENDnet

TRENDnet CAMEO/TEW-632BRP Manuale utente

TRENDnet

TRENDnet TW100-BRM504 Manuale utente

TRENDnet

TRENDnet TE100-S16 - DATA SHEETS Manuale utente

TRENDnet

TRENDnet TEG -S81 g Manuale utente

TRENDnet

TRENDnet TW100-BRF114 Manuale utente

TRENDnet

TRENDnet TW100-BRV214 Manuale utente

TRENDnet

TRENDnet TEW-722BRM Manuale utente

TRENDnet

TRENDnet TW100-BRF114 Manuale di istruzioni

TRENDnet

TRENDnet TW100-BRF104 Manuale utente

TRENDnet

TRENDnet TW100-BRM504 Manuale utente

TRENDnet

TRENDnet TVP-224HR Manuale utente

TRENDnet

TRENDnet TW100-BRV204 - VPN Firewall Router Manuale elenco delle parti

TRENDnet

TRENDnet TEW827DRUV2 Manuale utente

TRENDnet

TRENDnet TW100-BRF114 Manuale utente

TRENDnet

TRENDnet TE100-S16R Manuale di installazione e funzionamento

TRENDnet

TRENDnet TEW-755AP2KAC V1 Manuale utente

TRENDnet

TRENDnet TWG-BRF114 Manuale utente

TRENDnet

TRENDnet TW100-BRV324 Manuale utente

TRENDnet

TRENDnet TW100-BRF114 Manuale utente

TRENDnet

TRENDnet TW100-BRM504 Manuale utente

TRENDnet

TRENDnet TW100-BRV204 SHEETS Manuale utente

TRENDnet

TRENDnet GREENnet TEW-639GR Manuale utente

Manuali Router di rete popolari di altre marche

Allnet

Allnet ALL0333AU Manuale utente

HomeSeer

HomeSeer HT-SEL Manuale utente

Sercomm

Sercomm Genesis OC3505D Manuale utente

Billion

Billion BIPAC 5102 Series Manuale utente

TP-Link

TP-Link TD-8817 Manuale utente

Motorola

Motorola MR1900 Manuale utente

Digi

Digi IX14 Manuale utente

Cisco

Cisco NCS 540 Manuale

XAVi

XAVi X8821e Manuale utente

BEC

BEC 6200WZL Manuale utente

MikroTik

MikroTik hAP ac3 Series Manuale utente

Korenix

Korenix JetNet 5428G Series Manuale utente

NETGEAR

NETGEAR FS526T - Switch Manuale utente

Korenix

Korenix JetNet 5710G Series Manuale utente

Automated Logic

Automated Logic ZN551 Manuale del proprietario

Cisco

Cisco ASR 1000 Series Manuale dell'operatore

EnGenius

EnGenius ESR-9710 Manuale utente

Cisco

Cisco 805 Series Istruzioni operative e di sicurezza