Trikdis FLEXi SP3 Manuale utente

www.trikdis.com UAB Trikdis Draugystes g. 17, LT-51229 Kaunas, Lithuania +370 37 408 040 info@trikdis.lt

Security control panel

FLEXi SP3

User manual

(FLEXi SK232LCD keypad)

September 2021

www.trikdis.com 2 September 2021

FLEXi

SP3

user manual

Attention!

Read this user manual carefully.

A representative from the company installing the alarm system will explain which functions of the FLEXi SP3 security module

must be activated to ensure proper protection of the premises.

Trademarks and patents Other trade names used in this document may be trademarks or registered

trademarks belonging to their respective manufacturers or retailers.

Manufacturer UAB „Trikdis“,

Draugystes g. 17, LT-51229 Kaunas, Lithuania

Version This document is applicable to FLEXi SP3 security modules with firmware

version v1.00 and up.

Certification CE marking

European Union directives 2004/108/EC (EMC directive)

1999/5/EC (conformity directive)

Contact information for inquiries Contact information can be found on the website www.trikdis.c

www.trikdis.com 3 September 2021

FLEXi

SP3

user manual

Contents

1 ABOUT YOUR ALARM SYSTEM ...................................................................................................................................... 4

2 MAIN TECHNICAL SPECIFICATIONS ................................................................................................................................ 4

3 POWERING THE EQUIPMENT......................................................................................................................................... 4

4 GENERAL OPERATION OF THE ALARM SYSTEM ............................................................................................................. 4

4.1 TRANSMISSION OF ALERT MESSAGES ..................................................................................................................................... 4

4.2 ALARM SYSTEM OPERATION MODES ...................................................................................................................................... 5

4.3 CONTROL OF THE ALARM SYSTEM ......................................................................................................................................... 5

4.4 CONTROL ACCESS .............................................................................................................................................................. 5

4.5 SECURITY FUNCTIONS ......................................................................................................................................................... 5

4.6 ADDITIONAL FUNCTIONS ..................................................................................................................................................... 6

5 CONTROLLING THE ALARM............................................................................................................................................ 6

5.1 CONTROLLING THE ALARM WITH A SK232LCD KEYPAD ............................................................................................................ 6

5.2 QUICK ARMING/DISARMING OF THE ALARM SYSTEM ................................................................................................................. 7

5.3 ARMING THE ALARM IN ARM MODE ..................................................................................................................................... 7

5.4 ARMING THE ALARM IN STAY MODE ..................................................................................................................................... 7

5.5 ARMING THE ALARM IN SLEEP MODE ................................................................................................................................... 8

5.6 DISARMING THE ALARM (OFF MODE) ................................................................................................................................... 8

5.6.1 Switching off the alarm after it has been activated ................................................................................................. 8

5.7 TEMPORARY ZONE BYPASS (BYPASS FUNCTION) ....................................................................................................................... 9

5.8 VIEWING AND CLEARING ALARM ACTIVATION MEMORY ............................................................................................................. 9

5.9 RESETTING FIRE (SMOKE) SENSORS........................................................................................................................................ 9

5.10 EMERGENCY CALL BUTTONS ................................................................................................................................................. 9

5.11 TROUBLESHOOTING THE ALARM SYSTEM ................................................................................................................................ 9

5.12 PROGRAMMING USER CONTROL CODES ................................................................................................................................ 10

5.12.1 Changing the administrator code ...................................................................................................................... 10

5.12.2 Entering new User codes ................................................................................................................................... 10

5.12.3 Editing User codes ............................................................................................................................................. 10

5.12.4 Viewing partition statuses ................................................................................................................................. 10

5.12.5 Deleting User codes ........................................................................................................................................... 11

5.12.6 Duress code........................................................................................................................................................ 11

5.13 SETTING THE TIME AND DATE ............................................................................................................................................. 11

5.14 ADJUSTING THE KEYPAD VOLUME ....................................................................................................................................... 11

5.15 ADJUSTING THE BRIGHTNESS OF THE KEYPAD SCREEN AND BUTTONS .......................................................................................... 11

5.16 SETTING THE TEMPERATURE .............................................................................................................................................. 12

6 CONTROL USING IBUTTON KEYS .................................................................................................................................. 12

7 CONTROL USING RFID CARDS (TAGS) .......................................................................................................................... 12

8 CONTROL USING PHONE CALLS ................................................................................................................................... 13

9 CONTROL USING SMS MESSAGES ................................................................................................................................ 13

www.trikdis.com 4 September 2021

FLEXi

SP3

user manual

1 About your alarm system

The FLEXi SP3 control panel is part of a premise security and fire alarm system. It performs sensor signal processing and

signalizer control and has integrated GSM and WiFi modems that can transmit alert messages to the central monitoring station

and to users’ mobile phones.

Representatives of the company that installed the alarm system will explain the details on the operation, configuration and

control of Your alarm system.

2 Main technical specifications

Number of security zones 10 zones (20 zones if using ATZ), can be expanded to up to 32 zones using

expanders

Number of partitions Up to 8

Ways of alerting about danger Sound, indoor and/or outdoor sirens. Strobe lights. Transmission of messages

to central monitoring station and/or to users

Alert messages are transmitted To central monitoring station via GPRS to two addresses and/or via SMS

messages

To 8 user mobile phones via SMS messages

Safety requirements Meets safety requirements of the EN 60950 standard

User codes for control Up to 40 user control codes; allowed number of different iButton keys or RFID

cards – up to 40

Resistance to environmental influences

class

Meets demands of standard EN 50131 for Class II environmental classification

Operating conditions Temperature from -10 °C to +50 °C, relative humidity 80% at +20°C, no

condensation

Main power supply 230 V 50 Hz single-phase AC power network (through a step-down power

transformer). Power consumption no higher than 40 W

Backup power supply 12 V / 7 Ah battery. Current consumption no higher than 0,5 A

3 Powering the equipment

The control panel is powered by an AC power network, or, in case it fails, by a backup battery. When an AC power network is

available, the battery is charged and kept in standby mode. The time of operation using the backup battery is limited and

depends on the amount of current used by the alarm system. A voltage of 12 V is required to power additional equipment.

4 General operation of the alarm system

The security-fire alarm system consists of a signal processing board (the control panel), installed in a casing along with a step-

down power transformer and backup power supply battery, with intrusion, break-in, fire and other sensors, sound and light

signalers and control equipment connected to it.

If the alarm system is armed and any of the sensors are triggered, sound and light signalizers are turned on, and, if set, alert

messages are sent to the central monitoring station and to users. If the alarm is disarmed, it will only react to the triggering of

sensors that are set to operate continuously.

4.1 Transmission of alert messages

Alert messages can be transmitted to the CMS (central monitoring station) and/or to users. Messages are sent via the selected

connectivity channels, first to the CMS and only then to users via Protegus, SMS messages and/or phone calls.

www.trikdis.com 5 September 2021

FLEXi

SP3

user manual

4.2 Alarm system operation modes

Mode Description

OFF (DISARM) In this mode, only some of the zones are protected. The alarm will only react to events in zones

set to Fire, 24 hour, Silent 24h.

ARM In this mode, all zones are protected. The alarm will react to all possible events.

STAY In this mode, a part of the zones is protected, but movement is allowed in zones set to Interior

STAY and Instant STAY. If the alarm system is operating in this mode and a Delay zone is

violated, the alarm will activate only after the entry time has elapsed.

SLEEP In this mode, a part of the zones is protected, but movement is allowed in zones set to Interior

STAY and Instant STAY. If the alarm system is operating in this mode and a Delay zone is

violated, the alarm will activate immediately.

4.3 Control of the alarm system

The alarm system can be controlled using the following devices:

 Trikdis keypads FLEXi SK232LED W, SK232LCD;

 Paradox keypads K32+, K32LED, K32LCD, K636, K10LED V/H, K35, TM50, TM70;

 Crow keypads CR-16, CR-LCD;

 iButton keys;

 RFID cards;

 Electric switch, by changing the state of the zone selected by the keyswitch;

 Telephone (by phone call or by sending an SMS message with specific contents);

 Protegus app;

 Remote command from monitoring station.

4.4 Control access

Control codes are used to give different users different access levels for controlling the alarm system. The user control codes

are four digits long. When choosing and entering control codes, only numbers from 0 to 9 are used, other symbols are not

available.

Types of alarm system control codes:

 Administrator code – a six-digit combination (default code - 123456). There is only one administrator code. It cannot be

deleted, but it can be changed. The Administrator code allows to add or delete other users’ control codes. The

Administrator code cannot arm/disarm the alarm system;

 User code – a four-digit combination for arming/disarming the alarm system and for temporarily bypassing security

zones. It is recommended to assign every user a personal alarm control code. The memory of the FLEXi SP3 module can

store up to 40 user codes;

 SMS password – six-digit combination for controlling the alarm system via SMS messages (default code - 123456).

4.5 Security functions

Name Description

Bypass Temporarily (for one arming of the alarm system) bypasses a security zone when changing the alarm

status. The function is used when the alarm needs to be armed, but a zone is malfunctioning and the

fault cannot be easily repaired.

Bell Squawk The module can use a short siren signal to warn about the arming and disarming of the premise alarm

system.

Chime When the alarm system is disarmed, the module can warn that a zone is being violated by turning on

the keypad buzzer and/or a specially programmed PGM output.

www.trikdis.com 6 September 2021

FLEXi

SP3

user manual

Name Description

Re-ARM Used to protect against accidental disarming of the alarm. If the alarm system was disarmed via phone

call, but the Delay zone was not violated, the alarm system will automatically return to its previous

security mode after the Entry Delay time passes.

4.6 Additional functions

Name Description

Temperature

measurement

Up to 8 temperature sensors DS18B20, DS18S20 or one temperature and humidity sensor AM2301 can

be connected to the FLEXi SP3 module. Intervals of permitted temperatures can be set for each of them

individually. If the temperature changes beyond the set interval, an event message will be formed and

sent to users.

Remote control of

devices

Additional electronic devices can be connected to the FLEXi SP3 security module’s programmable open

collector outputs and can be controlled remotely.

5 Controlling the alarm

5.1 Controlling the alarm with a SK232LCD keypad

The keypad FLEXi SK232LCD for alarm system control displays the states of 32 zones and 8 partitions.

Buttons for setting operation modes and entering numbers

Button Description

The button is used for editing control codes and for resetting fire sensors.

Arrow button (used for menu navigation)

MENU The MENU button is used to open the advanced settings window

www.trikdis.com 7 September 2021

FLEXi

SP3

user manual

Button Description

1, 2 ...9, 0 Buttons for entering numbers.

C Button for exiting modes and clearing values.

OK Button for confirming the specified choice.

ARM Button for turning on full security mode ARM.

SLEEP Button for turning on SLEEP mode.

STAY Button for turning on STAY mode.

OFF Button for turning on OFF (DISARM) mode.

Note: 1. To turn off programming mode or delete an incorrectly entered value, press the [C] button.

2. If at least one zone is violated, it will not be possible to arm the alarm system (if the FORCE property

is not assigned to the violated zones).

5.2 Quick arming/disarming of the alarm system

Arming/disarming the alarm system using a code when the security system has STAY zones.

Security modes ARM, STAY and SLEEP are switched to OFF/DISARM, and OFF/DISARM is switched to ARM or STAY mode.

Changing the security mode:

1. Enter [User code].

a. If the security system has only one section, then skip step 2. If the system has several partitions, the numbers of the

partitions will appear on the keypad screen, the modes of which the user can change.

2. Press the numbers of the chosen partitions.

3. Disarming. Partitions that were in ARM, STAY and SLEEP modes will switch to OFF/DISARM mode.

a. When the security system is disarmed, the following text will appear on the keypad display: Disarmed: Area.

b. If the Bell Squawk function is enabled, the siren will activate twice for short periods of time as the alarm switches

off.

4. Arming. Exit delay time will be counted down for partitions that were in OFF/DISARM mode. If a Delay zone is violated

during the countdown, ARM mode will switch on, and if a Delay zone is not violated, STAY mode will switch on.

a. The corresponding text will appear on the keyboard screen: Armed: Area or Stay: Area.

b. If the Bell Squawk function is enabled, the siren will activate once for a short period of time as the alarm switches

on.

5.3 Arming the alarm in ARM mode

To turn on ARM security mode for an security system that is divided into multiple partitions:

1. Press the keypad button [ARM].

2. Enter the [User code] using the keypad.

3. Press the buttons with the numbers of the partitions you want to control.

4. Confirm your selection by pressing the [OK] button.

5. Before the Exit Delay time runs out, leave the premises and close the door.

a. During the Exit Delay time countdown, the exit time will be displayed on the keypad screen. When the security

system is armed, the following text appears on the keypad display: Armed: Area.

b. If the Bell Squawk function is enabled, the siren will activate once for a short period of time as the alarm switches

on.

5.4 Arming the alarm in STAY mode

To turn on STAY security mode for an alarm system that is divided into multiple partitions:

1. Press the keypad button [STAY].

www.trikdis.com 8 September 2021

FLEXi

SP3

user manual

2. Enter the [User code] using the keypad.

3. Press the buttons with the numbers of the partitions you want to control.

4. Confirm your selection by pressing the [OK] button.

5. The following text will appear on the keypad screen: Stay: Area.

a. If the Bell Squawk function is enabled, the siren will activate once for a short period of time as the alarm switches

on.

Note: STAY mode is unavailable unless at least one zone is set to Interior STAY or Instant STAY.

5.5 Arming the alarm in SLEEP mode

To turn on SLEEP security mode for an alarm system that is divided into multiple partitions:

1. Press the keypad button [SLEEP].

2. Enter the [User code] using the keypad.

3. Press the buttons with the numbers of the partitions you want to control.

4. Confirm your selection by pressing the [OK] button.

5. The following text will appear on the keypad screen: Sleep: Area.

a. If the Bell Squawk function is enabled, the siren will activate once for a short period of time as the alarm switches

on.

Note: SLEEP mode is unavailable unless at least one zone is set to Interior STAY or Instant STAY.

5.6 Disarming the alarm (OFF mode)

When the premises are secured in ARM or STAY mode, the countdown of the Entry Delay time will begin if anyone enters the

premises. You must disarm the alarm before the time runs out.

To switch off protection mode (switch on OFF / DISARM mode):

1. Press the keypad button [OFF].

2. Enter the [User code] using the keypad.

a. If the system has only one partition, skip steps 3 and 4.

3. Press the buttons with the numbers of the partitions you want to control.

4. Confirm your selection by pressing the [OK] button.

a. When the security system is disarmed, the following text appears on the keypad display: Disarmed: Area.

b. If the Bell Squawk function is enabled, the siren will activate twice for a short period of time as the alarm switches

off.

5.6.1 Switching off the alarm after it has been activated

To switch off the alarm:

1. Enter the [User code].

a. If the system has only one partition, skip steps 2 and 3.

2. Press the buttons with the numbers of the partitions you want to control.

3. Confirm your selection by pressing the [OK] button.

a. When the security system is disarmed, the following text appears on the keypad display: Disarmed: Area.

b. If the Bell Squawk function is enabled, the siren will activate twice for a short period of time as the alarm switches

off.

c. The following text will appear on the keypad screen: Service [MENU]: Memory. Press the [MENU] button, then [3],

and the display of damaged zones will appear on the screen. Press [C] to quit viewing damaged zones.

www.trikdis.com 9 September 2021

FLEXi

SP3

user manual

5.7 Temporary zone bypass (Bypass function)

To switch on the Bypass function:

1. Press the keypad button [MENU].

2. Press the [2] button on the keypad.

3. Enter the [User code].

4. Enter the two-digit numbers of the zones that you want to bypass.

5. Confirm your selection by pressing the [OK] button.

6. The keypad will exit zone bypassing mode.

To switch off the Bypass function, repeat the same steps as above.

5.8 Viewing and clearing alarm activation memory

When the security system is activated, the following text will appear on the keypad screen: Service [MENU]: Memory. To find

out the reason of the alarm activation:

1. Press the keypad button [MENU].

2. Press the [3] button on the keypad.

3. A list of violated zones that have triggered the alarm will appear on the screen.

4. To exit this mode, press the [C] button.

a. If no operations are performed on the keypad, the memory preview mode will turn off automatically after one

minute, but the information will remain in the memory and the display will show: Service [MENU]: Memory.

5. The memory will be cleared when the security system is armed.

5.9 Resetting fire (smoke) sensors

After the triggering of fire (smoke) sensors, to reset the sensors you must:

1. Press and hold the keypad button [ ] for 3 seconds.

a. The PGM output that the fire sensors are connected to and that is set to operate in Fire sensor reset mode will

activate.

b. The fire (smoke) sensors connected to the control panel’s zone will be reset.

5.10 Emergency call buttons

The keypad can be used to send messages to the security company about required help or imminent danger. This feature is

only available if you are using the services of a security company and the security system is connected to the central monitoring

station. The installer must activate the emergency call buttons. The buttons are activated in TrikdisConfig in the "Modules /

Keypads / Keypad parameters" menu branch.

Hold down the following buttons together for 3 seconds:

 [1] to send a message Panic about imminent danger.

 [4] to send a message Medical about the need for medical assistance.

 [7] to send a message Fire.

5.11 Troubleshooting the alarm system

If there is any operational trouble, the following text appears on the keypad screen: Service [MENU]: Trouble. To view

operational trouble of the alarm system:

1. Press the [MENU] button.

2. Press the [1] button.

3. Trouble groups will be displayed on the keypad screen.

4. If you want to view a trouble group, press the corresponding button.

5. To leave troubleshooting mode, press the [C] button.

www.trikdis.com 10 September 2021

FLEXi

SP3

user manual

Trouble descriptions

Trouble group Description of selected group

[1]: Wireless zone battery

[2]: Power trouble [1] Low/No Battery

[2] AC lost

[3] AUX trouble

[3]: Bell trouble

[4]: Communication trouble

[5]: Zone tamper

[8]: Clock loss

[9]: Wireless zone lost

[10]: Expansion module lost

5.12 Programming user control codes

5.12.1 Changing the administrator code

The Administrator code can be changed in TrikdisConfig software’s menu branch System Options / Access / Access codes.

5.12.2 Entering new User codes

1. Press the [ ] button on the keypad.

2. Enter the 6-digit [Administrator code].

3. Enter a free two-digit user serial number.

4. Enter a 4-digit [User code].

5. Repeatedly enter the 4-digit [User code].

6. Enter the partitions that the user will be able to control.

7. Confirm your selection by pressing the [OK] button.

8. To leave programming mode, press the [C] button.

5.12.3 Editing User codes

1. Press the [ ] button on the keypad.

2. Enter the 6-digit [Administrator code].

3. Enter the desired two-digit user serial number.

4. Enter the 4-digit [User code].

5. Repeatedly enter the 4-digit [User code].

6. Enter the partitions that the user will be able to control.

7. Confirm your selection by pressing the [OK] button.

8. To leave programming mode, press the [C] button.

5.12.4 Viewing partition statuses

Viewing states of the current partitions. Press the [OK] or [C] key and the status of the areas will be displayed on the keypad

screen.

Altri manuali per FLEXi SP3

Indice

Altri manuali Trikdis Pannello di controllo

Trikdis

Trikdis FLEXi SP3 Istruzioni per il montaggio

Trikdis

Trikdis FLEXi SP3 Manuale utente

Trikdis

Trikdis CG17 Manuale utente

Trikdis

Trikdis SP231 Manuale utente

Trikdis

Trikdis FLEXi SP3 Manuale utente

Trikdis

Trikdis SP231 Istruzioni per il montaggio

Manuali Pannello di controllo popolari di altre marche

RDZ

RDZ PC-HRX Manuale utente

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Manuale tecnico

Efka

Efka Variocontrol V810 Manuale utente

Cebora

Cebora 208-10 Manuale utente

AMX

AMX AutoPatch CP-15 Manuale utente

Satel

Satel CA-6 KLED-S Manuale utente

Evolution

Evolution IQ plus 800 Manuale utente

Fagor

Fagor 8040 TCO CNC Manuale utente

Trane

Trane ComfortLink II XL950 Control Manuale utente

AKO

AKO PROCool AKO-17635-2 Manuale utente

ABB

ABB 6136/30M-101 Manuale utente

Telikou

Telikou BK-603 Belt Pack Manuale utente

Mapei

Mapei Mapeheat Thermo Touch Manuale utente

Bosch

Bosch D9412GV4 Manuale utente

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Manuale utente

Sminn

Sminn BOX L VF1L EI Manuale utente

Balboa

Balboa TP600 Manuale utente

Nice

Nice HSCU1 Specifiche tecniche