Trust ACM-3000H2 Manuale utente
START-LINE
ACM-3000H2
ACM-3000H2 BUILT-IN SWITCH
Item 71148 Version 1.0
Visit www.trust.com
for the latest instructions
USER MANUAL
MULTI LANGUAGE
2
4
1
3
5mm
3A
3B
65
7
L
i
v
e
w
i
r
e
N
e
u
t
r
a
l
w
i
r
e
01 02
Com S1 S2 N L
L
i
v
e
w
i
r
e
L
i
v
e
w
i
r
e
N
e
u
t
r
a
l
w
i
r
e
S
w
i
t
c
h
w
i
r
e
01 02
Com S1 S2 N L
01 02Com S1 S2 N L
S
w
i
t
c
h
w
i
r
e
t
o
l
a
m
p
2
S
w
i
t
c
h
w
i
r
e
t
o
w
a
l
l
s
w
i
t
c
h
2
9.1
8
PP
01 02 S1 S2 N L
COM
L
N
Wall switch
P
Wall switch
Wall switch
P
Wall switch
ACM-3000H2
Switch 1a
Switch 2a
Switch 1b Switch 2b
L
N
n
u
l
d
r
a
a
d
01 02Com S1 S2 N L
1 SEC
PP
01 02 S1 S2 N L
COM
L
N
Wall switch
Wall switch
ACM-3000H2
Switch 2Switch 1
9.2
10
9.3
11
ON
01 02Com S1 S2 N L
2x
ININ OUT
L
N N
n
u
l
d
r
a
a
d
01 02Com S1 S2 N L
n
u
l
d
r
a
a
d
01 02Com S1 S2 N L
01 02Com S1 S2 N L
1 SEC
2x
OFF
01 02Com S1 S2 N L
n
u
l
d
r
a
a
d
01 02Com S1 S2 N L
8 SEC 1 SEC
2x
1
ACM-3000H2 BUILT-IN SWITCH
1. Disable mains power
Always turn OFF the mains power (In the meter closet) before you begin the installation or removal
of this product. The ACM-3000H2 can be used for either one or two hotel switches, connected with
one or two lamps. Also, the ACM-3000H2 can be used for one or two single wall switches, which are
connected with one or two lamps.
2. Loosen ceiling lights
Remove the existing lighting/equipment from the ceiling, leaving the wires connected to the lighting.
Lighting/equipment, may not exceed the maximum of 3000 watts.
3. Warning for stripping wires
3A. Make sure the wires are stripped for 5mm.
3B. When connecting the wires to the ACM-3000H2 make sure the stripped wires are pressed firmly
in the module, no exposed wires are visible and the wires cannot touch each other. This can cause a
short circuit.
4. Disconnect the switch wire and neutral wire
To install the ACM-3000H2 disconnect the switch wire and neutral wire of lamp 1. (Disconnect from
terminal block or cut the wires if necessary) Disconnect the switch wire and neutral wire of lamp 2.
Consult an electrician if in doubt about wire colours.
5. Connect the live wire and the neutral wire to a terminal block
(a) Connect the live wire from the ceiling box to a terminal block. Connect the other end of the live
wire also back into the same terminal block.
(b) Connect the neutral wire from the ceiling box to a dierent terminal block. Make sure other Trust
Smart Home receivers are placed at least 50 cm from the ACM-3000H2 to prevent interference.
6. Connect the switch wire and neutral wire of the lamp to the terminal block
(a) Connect the wall switch wire of lamp 1 from the ceiling box to the [S1] contact.
(b) Connect the (blue) neutral wire from lamp 1 to the terminal block of the neutral wire. Connect a
new wire from the neutral terminal block on to the [N] contact.
(c) Connect the switch wire from lamp 1 on to the [O1] contact.
EN
ACM-3000H2 BUILT-IN SWITCH
2
(d) Connect two new live wires from the live wire terminal block to the [L] and [COM] contact.
(e) Tighten the terminal screws of the ACM-3000H2.
7. Connect second lamp and wall switch.
(a) Pull the switch wire from the wall switch of lamp 2 to the ceiling box of lamp 1. Pull the switch wire
from lamp 2 to the ceiling box of lamp 1.
(b) Connect the switch wire of lamp 2 to the [O2] contact
(c) Connect the switch wire from the wall switch of lamp 2 to the [S2] contact.
This is an technical installation schematic of the ACM-3000H2 with two wall-switches (1 hotel/stairwell
circuit).
This is an technical installation schematic of the ACM-3000H2 with four wall-switches (2 hotel/stairwell
circuit.
8. Enable mains power
Switch the mains power ON before proceeding with the installation.
Make sure no stripped parts of wires are touched after this step.
The LED indicator on the receiver will be lit for a few seconds when voltage is applied.
9.1 Activate pairing mode
Press for about 1 second (with a pointed object) on the Connect button to activate the pairing mode.
The pairing mode will be active for 15 seconds and the LED indicator on the receiver will flash slowly.
9.2 Send an ON signal
While the LED indicator flashes, press the ON button on a Trust Smart Home transmitter to pair the
transmitter to the ACM-3000H2. (Or activate a Trust Smart Home sensor).
EN
3
ACM-3000H2 BUILT-IN SWITCH
9.3 Pairing confirmation
The LED on the module will blink 2x in order to confirm that the code is stored. Repeat steps 9.1 to 9.3
for the second lamp with the other pairing button. The receiver can store up to 6 dierent transmitter
codes in its memory per channel. The memory is retained when the receiver is installed elsewhere or
when there is a power failure.
10. Placing the receiver
Place the receiver in the ceiling box. Mount the lights back in place or use a cover.
Make sure that you can always reach the receiver, for example, to reset it, or to register a new
transmitter.
Make sure no stripped parts of wires touch each other.
11. Wireless control
Send with the transmitter an ON signal to turn the light on wirelessly.
Send with the transmitter an OFF signal to turn the light o wirelessly.
Consult the manual of the transmitter for more information.
The existing wall switches which are used to control the connected lighting can still be used.
Deleting a single transmitter code
(a) Press for about 1 second on the Connect button. The ‘pairing mode’ will be active for 15 seconds
and the LED indicator on the receiver will flash slowly.
(b) Send while the ‘pairing mode’ is active with the connected Trust Smart Home transmitter an
OFF signal. If necessary, consult the instruction manual of the transmitter.
(c) The LED on the module will flash 2x to confirm that the code has been removed.
Repeat this procedure to delete several transmitters from the receiver.
EN
ACM-3000H2 BUILT-IN SWITCH
4
EN
Erase entire memory
(a) Press the Connect button for about 8 seconds until the LED indicator flashes quickly.
(b) When the LED indicator flashes rapidly, press the Connect button again for 1 second to confirm
that you want to completely erase the memory.
(c) The LED on the module flashes 2x to confirm that the memory has been erased.
Altri manuali per ACM-3000H2
1
Indice
Altri manuali Trust Interruttore
Trust
Trust START-LINE AMU-500 Manuale utente
Trust
Trust SMART Home START-LINE RECEIVER AWMR-300 Manuale operativo
Trust
Trust SmartHome ACM-1000 Manuale utente
Trust
Trust START-LINE ACM-2000 Manuale utente
Trust
Trust APC Starter Set Wireless Switching Manuale utente
Trust
Trust HU-4445p Manuale utente
Trust
Trust PREMIUM ZCM-1800 Manuale utente
Trust
Trust HU-3340p Manuale utente
Trust
Trust SMART Home AWMR-230 Manuale utente
Trust
Trust ZCC-3500 Manuale utente
Trust
Trust 11670 Manuale utente
Trust
Trust 17079 Aggiornamento firmware
Trust
Trust SECURITY PLUS-LINE AGST-8800 Manuale utente
Trust
Trust START-LINE AGST-8800 Manuale utente
Trust
Trust ASUN-650 Manuale utente
Trust
Trust START-LINE ACC-2300 Manuale utente
Trust
Trust HU-1140P Manuale utente
Trust
Trust START-LINE AWMR-230 Manuale operativo
Trust
Trust 73182 Manuale utente
Trust
Trust START-LINE ACM-2300-HC Manuale utente
