Turck BL67 Manuale utente

G1011

Revised 1/14/2014

HOW TO

How to Flash BL67/BL20 RFID

Using a Universal Programming

Dongle and Memtool 3

2www.turck.com • 1-800-544-7769 • Fax: (763) 553-0708 • TURCK • Minneapolis, MN 55441 www.turck.com • 1-800-544-7769 • Fax: (763) 553-0708 •TURCK • Minneapolis, MN 55441 3

MATERIALS LIST

BL 20 Materials Hardware list:

• 1) RS 232 cable

• 2) RS 232 to Universal Dongle converter

• 3) Universal Programming Dongle

• 4) Card Connector

• 5) 5V power supply

• 6) BL 67 cards your ashing

• 7) Soldering iron

• 8) Solder

• 9) Scalpel

• 10) Clamp

BL20 Material Software List:

• 1) Windows XP operating system

• 2) Memtool 3

• 3) Most recent version of the 2RFID-A or 2RFID-S rmware le

BL 67 Materials Hardware list:

• 1) RS 232 cable

• 2) RS 232 to Universal Dongle converter

• 3) Universal Programming Dongle

• 4) Card Connector

• 5) 5V power supply

• 6) BL 67 cards your ashing

BL67 Material Software List:

• 1) Windows XP operating system

• 2) Memtool 3

• 3) Most recent version of the 2RFID-A or 2RFID-S rmware le

www.turck.com • 1-800-544-7769 • Fax: (763) 553-0708 •TURCK • Minneapolis, MN 55441 3

IMPORTANT NOTES:

1. The Universal Programming Dongle can ONLY handle 5 Volts. (Please do not burn up your dongle by putting too

much voltage through it.)

2. I’ve have only been able to ash using a Windows XP operating system. (It appears that my Windows 7 64 bit

operating system is to new of a computer perform ashing.)

SETUP THE STATION:

-> Hook the 1) RS232 cable to the back of your computer -> Hook the other end of the RS 232 cable to the 2) RS232 to

Universal Dongle converter -> Hook the converter to the 3) Universal Dongle itself -> Leave the 4) Card Connector alone

for the moment -> Hook the power leads up to the 5) Power Supply.

4www.turck.com • 1-800-544-7769 • Fax: (763) 553-0708 • TURCK • Minneapolis, MN 55441 www.turck.com • 1-800-544-7769 • Fax: (763) 553-0708 •TURCK • Minneapolis, MN 55441 5

If you are ashing a BL67 card, please skip to page six. If you’re ashing a BL20, please read on.

LET’S FLASH A BL20 CARD.

-> Remove the card from the casing

-> Bring the card to your solder station and nd pin 1 of the top right micro chip (Look at the pictures)

www.turck.com • 1-800-544-7769 • Fax: (763) 553-0708 •TURCK • Minneapolis, MN 55441 5

-> Gently remove pin 1 using your soldering iron and scalpel

-> This is what your chip should look like once pin 1 is removed

6www.turck.com • 1-800-544-7769 • Fax: (763) 553-0708 • TURCK • Minneapolis, MN 55441 www.turck.com • 1-800-544-7769 • Fax: (763) 553-0708 •TURCK • Minneapolis, MN 55441 7

-> Bring the card back to your ashing station and hook it up to the Card Connecter (Note: If the Card Connecter is

touching the even connectors on the card it will not ash.)

SET UP THE UNIVERSAL PROGRAMMING DONGLE

-> Make sure the switch is to the right -> Hit reset before you begin programming in Memtool 3 (You also must hit the

reset switch before every card you program)

www.turck.com • 1-800-544-7769 • Fax: (763) 553-0708 •TURCK • Minneapolis, MN 55441 7

-> Open Memtool 3

-> Open le -> Choose your rmware le -> Open

8www.turck.com • 1-800-544-7769 • Fax: (763) 553-0708 • TURCK • Minneapolis, MN 55441 www.turck.com • 1-800-544-7769 • Fax: (763) 553-0708 •TURCK • Minneapolis, MN 55441 9

-> Highlight the rmware le -> Connect

-> Add Set -> Program

www.turck.com • 1-800-544-7769 • Fax: (763) 553-0708 •TURCK • Minneapolis, MN 55441 9

-> Let the program run

IMPORTANT NOTES:

1. When the programming has nished, remember to solder pin 1 back down. (BL20 users)

2. Every time you ash and new a new card you must hit the reset on the Universal Programming Dongle.

TROUBLE SHOOTING SOLUTIONS

-> If you get an error message in Memtool 3, here are some possible faults.

1. You forgot to hit the reset button on the Universal Programming Dongle. Hit the reset.

2. The Card Connecter is touching the even connections on the card. Readjust it.

3. You did a poor job unsoldering pin 1. Check your work and try it again.

4. You allowed the soldering iron to touch the microchip, which in turned burned up the card’s circuitry. Throw it away.

5. You didn’t set up the Universal Programming Dongle correctly. Recheck it.

6. You ran more than 5V through the dongle and the dongle burned up. Try a dierent one.

7. Maybe the card is bad to start. Check it in PACTware of Xion Tool.

8. If one card just won’t connect, try a dierent card.

IMPORTANT NOTE:

EVERY TIME YOU DO A TROUBLE SHOOTING SOLUTION YOU MUST COMPLETELY CLOSE OUT AND

RESTART MEMTOOL.

Altri manuali per BL67

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali turck Unità di controllo

turck

turck FDN-DN1 Manuale utente

turck

turck TBEN-L 8IOL Series Manuale utente

turck

turck TBEN-S2-4IOL Manuale utente

turck

turck TBEN-LL-8IOL Manuale utente

turck

turck TBEN-Lx-8IOL Manuale utente

turck

turck TBEN-S Series Manuale utente

turck

turck IO-LINK MASTER Manuale utente

turck

turck FXDP Series Manuale utente

turck

turck TBPN-L1-FDIO1-2IOL Manuale utente

turck

turck DF20-N Manuale utente

turck

turck TBEC-LL-4RFID-8DXP Manuale utente

turck

turck TBIP-L 4FDI-4FDX Series Manuale utente

turck

turck TBEN-LH-8IOL Manuale utente

turck

turck FMX-IM-3UR38X Manuale utente

turck

turck excom I/O System Manuale per l'uso e la cura

turck

turck TX700 HMI/PLC Series Manuale utente

turck

turck TX-EXTEND Manuale utente

turck

turck TBEN-RFID Series Manuale tecnico

turck

turck TBPN-L FDIO1-2IOL Series Manuale utente

turck

turck IM18-CCM51-12I Manuale utente

turck

turck TBEN EN1 Series Manuale utente

turck

turck excom-RMD1-BU Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente

turck BL67 Manuale utente

Manuali Unità di controllo popolari di altre marche