Ubiquiti UF-Instant Manuale utente

UFiber Instant

Package Contents

Installation Requirements

UFiber OLT

Ubiquiti product with SFP port

For more information, refer to:

ubnt.link/Using-UF-Instant

Before You Begin

Designing your ﬁrst GPON deployment requires speciﬁc knowledge and planning. For

information on GPON network design and installation, including important considerations

and best practices, refer to:

ubnt.link/UFiber-GPON-Getting-Started

ubnt.link/Designing-a-GPON-Network

For details on conﬁguring U Fiber devices for the ﬁrst time, refer to:

ubnt.link/UFiber-

Initial-Conﬁguration

Hardware Overview

UF-Instant Quick Start Guide

PON Port

SGMII Interface

The SC/APC GPON port supports WAN connections of 2.488 Gbps downstream and

1.244 Gbps upstream.

The SGMII Ethernet LAN interface supports a 1 Gbps connection.

Connecting Fiber

WARNING:

Never look directly into the ends of ﬁber or modules. The emitted light

could cause damage to the eye.

WARNING:

Until ready for use, keep modules and ﬁber patch cables covered using

the included protective caps to ensure the connections stay clean.

WARNING:

DO NOT connect the device directly to a UFiber GPON module (UF-GP-

B+ or UF-GP-C+). Doing so will damage the device optics. Ensure that the device’s

received signal level never exceeds -8 dBm. Use a UFiber PLC Splitter to add

attenuation as needed.

UF-Instant Quick Start Guide

Connecting LAN

UF-Instant Quick Start Guide

Conﬁguration

The device only supports bridge mode and is conﬁgured via the UFiber OLT. For more

information, refer to the UFiber resources, which are available at:

ubnt.link/UFiber-

Support

Speciﬁcations

UF-Instant

Dimensions 69.46 x 13.70 x 11.30 mm

(2.74 x 0.54 x 0.45")

Weight 30 g (0.96 oz)

Networking Interfaces (1) SC/APC, GPON WAN

(1) SGMII Ethernet LAN

Networking Interface Speeds

GPON WAN, ITU G.984 2.488 Gbps Downstream,

1.244 Gbps Upstream

GbE LAN 1 Gbps

Management Interface In-Band Ethernet

PON

Normal Optical Power Range TX (Class B+): 0.5 to 5 dBm

RX: -8 to -28 dBm

Power Method SFP

UF-Instant Quick Start Guide

UF-Instant

Power Supply 3.3V

Max. Power Consumption 2W

Supported Voltage Range 3.3V

Processor Specs MIPS 100 MHz

Memory Information 32 MB DDR

Operating Temperature -10 to 45° C (14 to 113° F)

Operating Humidity 10 to 90% Noncondensing

Certiﬁcations CE, FCC, IC

Safety Notices

1. Read, follow, and keep these instructions.

2. Heed all warnings.

3. Only use attachments/accessories speciﬁed by the manufacturer.

WARNING:

To reduce the risk of ﬁre or electric shock, do not expose this product to rain or

moisture.

WARNING:

Do not use this product in location that can be submerged by water.

WARNING:

Avoid using this product during an electrical storm. There may be a remote risk of

electric shock from lightning.

WARNING:

CLASS 1 LASER PRODUCT, IEC/EN 60825

‑

1:2014 - Do not look into the ends of the

ﬁber optic cable or SFP modules while converters are powered.

Electrical Safety Information

1. Compliance is required with respect to voltage, frequency, and current requirements indicated on

the manufacturer’s label. Connection to a diﬀerent power source than those speciﬁed may result in

improper operation, damage to the equipment or pose a ﬁre hazard if the limitations are not

followed.

2. There are no operator serviceable parts inside this equipment. Service should be provided only by a

qualiﬁed service technician.

Limited Warranty

ui.com/support/warranty

The limited warranty requires the use of arbitration to resolve disputes on an individual basis, and,

where applicable, specify arbitration instead of jury trials or class actions.

UF-Instant Quick Start Guide

Compliance

FCC

Changes or modiﬁcations not expressly approved by the party responsible for compliance could void

the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions.

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that may cause undesired

operation.

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment oﬀ and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit diﬀerent from that to which the receiver is

connected.

Consult the dealer or an experienced radio/TV technician for help.

ISED Canada

CAN ICES-3(B)/NMB-3(B)

Australia and New Zealand

CE Marking

CE marking on this product represents the product is in compliance with all directives that are

applicable to it.

WEEE Compliance Statement

UF-Instant Quick Start Guide

Declaration of Conformity

Online Resources

UF-Instant Quick Start Guide

Altri manuali Ubiquiti Hardware di rete

Ubiquiti

Ubiquiti U-Installer Manuale utente

Ubiquiti

Ubiquiti UBB Manuale utente

Ubiquiti

Ubiquiti USW-24 Manuale utente

Ubiquiti

Ubiquiti mPort-S mPort Serial Manuale utente

Ubiquiti

Ubiquiti UF-Instant Manuale utente

Ubiquiti

Ubiquiti UF-AE Manuale utente

Ubiquiti

Ubiquiti UniFi NVR Manuale utente

Ubiquiti

Ubiquiti UniFi LED ULED-AT Manuale utente

Ubiquiti

Ubiquiti UniFi USW-Flex-Mini Manuale utente

Ubiquiti

Ubiquiti AM-5AC21-60 Manuale utente

Ubiquiti

Ubiquiti PowerBeam AC Gen2 Manuale utente

Ubiquiti

Ubiquiti ES-10X Manuale utente

Ubiquiti

Ubiquiti uFiber OLT 4 Manuale utente

Ubiquiti

Ubiquiti UniFi Dream Machine Pro Manuale utente

Ubiquiti

Ubiquiti NS-5AC Manuale utente

Ubiquiti

Ubiquiti airFiber 60 Manuale utente

Ubiquiti

Ubiquiti 0810354025402 Manuale utente

Ubiquiti

Ubiquiti PowerBeam PBE-2AC-400-US Manuale utente

Ubiquiti

Ubiquiti PowerBeam airMAX AC Gen2 PBE-5AC-Gen2 Manuale utente

Ubiquiti

Ubiquiti RocketM Series Manuale utente

Ubiquiti

Ubiquiti UF-LOCO Manuale utente

Ubiquiti

Ubiquiti PowerBeam M PBE-M2-400 Manuale utente

Ubiquiti

Ubiquiti PBM3 Manuale utente

Ubiquiti

Ubiquiti R5AC-PTP Manuale utente

Manuali Hardware di rete popolari di altre marche

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuale utente

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuale utente

Yudor

Yudor YDS-16 Manuale utente

D-Link

D-Link ShareCenter DNS-320L Manuale utente

Samsung

Samsung ES1642dc Istruzioni per l’uso

Honeywell Home

Honeywell Home LTEM-PV Istruzioni per il montaggio

evertz

evertz 7700 Series Manuale utente

D-Link

D-Link ShareCenter DNS-343 Manuale utente

Asante

Asante AsanteBridge 1012 Manuale utente

FireBrick

FireBrick FB2700 Manuale utente

Audiovox Electronics

Audiovox Electronics ARWH2T Manuale utente

ADC

ADC DSX-1 Manuale

NetComm

NetComm NF2 Manuale utente

Alcatel-Lucent

Alcatel-Lucent 5620 Manuale utente

Dell EMC

Dell EMC XC6420 Series Manuale utente

Lanner

Lanner NCA-1020A Manuale utente

Allied Telesis

Allied Telesis AT-TN121-A Manuale utente

Arista

Arista CCA-ETM-Q12 Manuale utente