uBuild-3D MR BOT 280 Manuale utente
Quick Start Guide
UBUILD-3D
MR BOT 280
Mr Bot 280
2
Preparing your printer
Opening the box
The uBuild-3D Mr Bot 280 printer is very well packaged in a five-card carton and
foam-protected polyethylene.
Open the box and remove the protective cardboard with polyethylene foam.
Lift the printer with your hands as shown below.
Setting up the printer
After removing the packaging, to operate your printer you only need two steps,
a) assembling the LCD display, and b) installing the spool holder. Your printer
settings are entirely based on the relevant function menu.
Mr Bot 280
3
A. Assembly of the LCD display
What you will need for the assembly:
1. Allen key 2mm
2. Allen key 2,5mm
3. LCD rear panel 1x
4. LCD display (pre-assembled) 1x
5. Rectangular sheet metal
6. M3x6mm button head screws 3x
7. M4x6mm button head screws 3x
8. M3x6mm countersunk screws
Mr Bot 280
4
Step 1
Locate the holes on the LCD rear panel
(5) before you proceed to screw the
rectangular sheet metal.
Step 2
With the M3x6mm half-rounded head
screws (2), screw the LCD’s rear panel
(5) with the rectangular sheet metal.
Step 3
Locate where to attach the sub-
assembly under the printer and screw it
in place with the M4x6mm half-
rounded head screws, as shown in the
photo.
Mr Bot 280
5
Step 4
Your semi-assembled printer should
look like in the photo.
Step 5
Connect the numbered ribbon cables
to the corresponding numbered plugs
on the back of the LCD display.
Step 6
Screw the pre-assembled part of the
LCD display to the printer's sub-
assembly with the three M3x6mm
screws (4).
Mr Bot 280
6
B. Mounting the spool holder and teflon tube brackets
What you will need for the assembly:
1. Teflon tube bracket 1x
2. Teflon tube bracket with pneumatic connector 1x
3. Teflon tube 1x
4. Allen key 2,5mm
5. M4x6mm button head screws 4x
Mr Bot 280
7
Step 1
With the M4x6mm half-rounded head
screws, screw the teflon tube brackets
to the right of the printer. The bracket
with the pneumatic connector goes to
the lower position (see circle).
Step 2
Pass the tube from the top bracket and
slide it down.
Step 3
Push it into the pneumatic connector as
far as it goes.
Mr Bot 280
8
Step 4
Connect the other end of the tube to
the extruder's pneumatic connector.
Step 5
Mount the spool holder. First diagonal
and up, as in the photo, so the top
bracket of the spool holder passes from
the center hole, and then slide down so
the two little brackets attach with the
two rectangular holes.
Mr Bot 280
9
Nozzle and print surface adjustment
After the assembly of the LCD display and the placement of the spool holder,
you need to adjust the correct distance between the nozzle and the printing
surface.
What you will need:
1. Calibration sheet 1x
Note:
The first time you will use the
calibration sheet, remember to fold it
up at the dotted lines. This way it will
be easier to move it back and forth
with your fingers.
Mr Bot 280
10
Step 1
Connect the power cord to the printer
and then to the wall outlet. Start the
printer with the "POWER" button on the
left of the printer and wait until this
image menu appears.
Step 2
To access the menu, press the LCD’s
knob and turn clockwise or
counterclockwise.
Step 3
Access in the basic menu you will find
the "Calibration" downwards. Select it.
Select the "Yes" command and then the printer setup program will start. When
the print head completes its movements and goes to the center of the print
surface, you will need to take some steps to complete this section.
Altri manuali per MR BOT 280
1
Indice
Altri manuali uBuild-3D Stampante 3D
