Uplift Desk STR045 Manuale utente
Slim Under Desk Shelf
STR045
Scan QR code for
product webpage
For assembly assistance, visit upliftdesk.com/contact, call 800-349-3839, or email [email protected]
©2023 UPLIFT Desk®. All Rights Reserved
Work Better. Live Healthier
2
Step 1 - Mark Shelf Attachment
Locations
A. Determine where you would like to install the shelf. It
should be in a location where it won’t interfere with
anything directly under the desktop, such as a keypad,
frame parts, or other accessories. We recommend
ush with the front edge of the desktop for ease of
installation and access.
B. Place the template against the underside of the desk
with the cutout facing the front of the desktop.
C. Align the front edge of the template to be ush with
the front edge of the desktop.
D. Use a pencil or pen to make a mark in the center of
each of the four holes in the template.
Under no circumstances does the manufacturer accept warranty or liability claims for damages caused from
improper use of this product. Please provide these instructions to any new user or owner of the product.
CAUTION: Read all instructions before assembly. Failure to assemble or operate properly may result
in damage or personal injury. Retain manual for future reference.
CAUTION: The recommended weight capacity for the shelf is 75 lb. Do not hang off the shelf, as it
may result in damage or personal injury.
Safety and Warnings
Assembly Instructions
Shelf Installation Template #10 x 5/8” Wood Screw
qty 4
Package Contents
Phillips Screwdriver Drill with 1/8” drill bit
You’ll also need
Cutout
3
© UPLIFT Desk • 800-349-3839 • info@upliftdesk.com • upliftdesk.com
Step 2 - Drill Shelf Attachment Holes
Softer desktop materials such as Laminate, Eco,
Rubberwood, or Acacia do not require drilling mounting
holes. If you have one of these desktops, you can skip to
Step 3.
For harder desktops, follow the steps below to create
mounting holes.
IMPORTANT: DRILL NO DEEPER THAN 1/2” to avoid drilling
through your desktop. To ensure this, wrap a piece of tape
around your drill bit 1/2” from the tip. Stop drilling just
before the tape touches the desktop.
A. Set the template aside. You can keep it if you think
you may move the shelf later, otherwise it can be
discarded.
B. Drill ½” deep pilot holes at the locations marked in
Step 1 using a 1/8” drill bit.
Step 3 - Attach Shelf
A. Desktop thickness should be at least ¾” to
accommodate the included screws. Before inserting
the screws, hold one next to the edge of the desktop
to make sure it will not protrude through the top once
installed.
B. Use a Phillips screwdriver to insert the screws about
¾ of the way into the holes drilled in Step 2 or at the
locations marked in Step 1. Leave about a ⅛” gap
between the underside of each screw head and the
desk surface.
C. Align the large hole in the shelf keyhole slots with the
screw heads and push up against the desktop.
D. Slide the shelf back so that the screws engage with the
keyhole slots and the front of the shelf is ush with the
front edge of the desktop.
X
0.5”
Tape
SAVE THIS MANUAL
Study this manual carefully. If this product is sold, please provide this
manual to the buyer, installers, or support personnel operating the product.
Work Better. Live Healthier
AI-STR045-1.0
Copyright Notice: This manual is a component of this UPLIFT Desk product. This manual is a
part of the scope of delivery, even if the item is resold. This manual is also available on the
UPLIFT Desk website: upliftdesk.com. This manual is subject to United States copyright law.
©
upliftdesk.com
800-349-3839
512-614-3152
Step 4 - Shelf Use
Your shelf is now ready to use. It accommodates laptops
(up to 17”), as well as phones, tablets, a wallet, keys, books,
les, or other small ofce accessories
When storing electronics inside the shelf, route the
device’s power and/or data cable through the side or
rear cable pass-throughs in the shelf to keep them
powered, charging, and connected. Cable pass-throughs
also facilitate using a laptop with an external keyboard,
mouse, and monitor.
Be sure to leave enough slack in the cables to access
devices while tethered and allow movement when
mounted to height adjustable desks.
The cable pass-throughs and ventilation slots on the
bottom of the shelf allow devices to remain cool while
powered and running.
Side cable
passthrough
Power cable
passthrough
Side cable passthrough
Ventilation slots
E. Insert the Phillips screwdriver through the screw access
holes in the bottom of the shelf and tighten the screws to
secure the shelf.
Indice
Altri manuali Uplift Desk Rack e supporto
Uplift Desk
Uplift Desk CPU001 Manuale utente
Uplift Desk
Uplift Desk ACC301 Manuale utente
Uplift Desk
Uplift Desk UPL021 Manuale utente
Uplift Desk
Uplift Desk ACC092 Manuale utente
Uplift Desk
Uplift Desk MON051 Manuale utente
Uplift Desk
Uplift Desk ACC305 Manuale utente
Uplift Desk
Uplift Desk ACC303 Manuale utente
Uplift Desk
Uplift Desk ACC304 Manuale utente
Uplift Desk
Uplift Desk ACC095 Manuale utente
Uplift Desk
Uplift Desk MON041 Manuale utente
Uplift Desk
Uplift Desk Motion-X 6-Pack Rack ACC052 Manuale utente
Uplift Desk
Uplift Desk UPL020 Manuale utente
Uplift Desk
Uplift Desk MON020 Manuale utente
Uplift Desk
Uplift Desk MON021 Manuale utente
Uplift Desk
Uplift Desk Zilker Dual Monitor Arm Manuale utente
Uplift Desk
Uplift Desk Zilker MON002 Manuale utente
Uplift Desk
Uplift Desk MON041 Manuale utente
Uplift Desk
Uplift Desk Crestview MON032 Manuale utente
Uplift Desk
Uplift Desk STR017-SHT Manuale utente
Uplift Desk
Uplift Desk ACC302 Manuale utente
