V-tech 202ca Manuale utente
1
Electronic Emission Notices
Federal Communications Commission (FCC) Statement (00302C)
This equipment has been tested and found to comply with the limits for a Class B digital
device,pursuanttoPart15ofFCCRules.Theselimitsaredesignedtoprovidereasonable
protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with instructions contained in this manual, may cause harmful interference
to radio and television communications. However, there is no guarantee that interference
will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
- REORIENTORRELOCATETHERECEIVINGANTENNA
- INCREASETHESEPARATIONBETWEENTHEEQUIPMENTANDTHERECEIVER
- CONNECTTHEEQUIPMENTINTOANOUTLETONACIRCUITDIFFERENTFROM
THATOFTHERECEIVER
- CONSULTTHEDEALERORANEXPERIENCEDAUDIO/TELEVISIONTECHNICIAN
NOTE: Connecting this device to peripheral devices that do not comply with Class B
requirements, or using an unshielded peripheral data cable, could also result in
harmful interference to radio or television reception.
The user is cautioned that any changes or modifications not expressly approved
by the party responsible for compliance could void the user’s authority to operate
this equipment.
To ensure that the use of this product does not contribute to interference, it is
necessary to use shielded I/O cables.
Copyright
This manual is copyrighted with all rights reserved. No portion of this manual may be
copied or reproduced by any means.
While every precaution has been taken in the preparation of this manual, no responsibility
for errors or omissions is assumed. Neither is any liability assumed for damages resulting
from the use of the information contained herein.
Trademarks
All brand names, logos and registered trademarks mentioned are property of their
respective owners.
2
Technical Reference Booklet
Table of Contents
HAR WARE CONFIGURATION .................................................................... 3
Key Features ............................................................................................................... 3
Motherboard Layout .................................................................................................... 5
Jumper Settings ........................................................................................................... 6
CPUSpeedSelection ............................................................................................ 6
CK1, CK4 - System Bus Frequency ..................................................................... 6
EDS1 - On Board AC97 Codec Sound ................................................................. 6
JBAT- CMOS Clear ............................................................................................... 6
JVSB1 - Keyboard Power Select......................................................................... 6
Pin Assignment ..................................................................................................... 7
HAR WARE SETUP ...................................................................................... 8
ToInstallDIMMs ........................................................................................................... 8
Installing a New Processor ......................................................................................... 9
To Install a Processor to ZIF Socket ........................................................................... 9
Connect the processor Fan Connector ...................................................................... 9
Setting the Processor Speed ...................................................................................... 9
BIOS SETUP .................................................................................................. 10
Starting Setup .............................................................................................................. 10
MainMenu.................................................................................................................... 11
Standard CMOS Features ........................................................................................... 12
Advanced BIOS Features ........................................................................................... 14
Advanced Chipset Features ....................................................................................... 14
Integrated Peripherals ................................................................................................. 14
Power Management Setup.......................................................................................... 14
PnP/PCIConfigurations ................................................................................................ 14
PCHealthStatus.......................................................................................................... 14
Frequency/Voltage Control ......................................................................................... 14
Set Supervisor/User Password.................................................................................. 14
Flash Update Procedure ............................................................................................. 16
SOFTWARE INSTALLATION .......................................................................... 17
PC-Cillin2000Installationfor WIN®9X ........................................................................ 17
Installing WIN®9X Driver for
Intel®815/815E/815P/815EPChipsetProducts .......................................................... 17
Sound Driver Installation ............................................................................................. 19
3
HARDWARE CONFIGURATION
Key Features :
Chipset
• Intel®815E/815EP Chipset.
Processor
• FullsupportfortheIntel®Pentium®IIIandCeleron®processors(FC-PGApackage)
using PGA370 socket.
• Support for Intel® Celeron® processors (FC-PGA package) and
Intel® Pentium® III processors (100MHz/133MHz system bus).
• 66/100/133MHz System Bus Frequency.
VRM 8.4 (Voltage Regulator Modules) on Board
• Flexible motherboard design with on board VRM 8.4, easy to upgrade with
future Intel® Pentium® III and Celeron® (FC-PGA package) processors.
System Memory
• A total of three 168-pin DIMM sockets.
• Supports up to 3 double sided DIMMs at 100MHz system memory bus.
• Supportsupto 2 double sided or 3 single sided DIMMs at133MHzsystemmemory
bus.
• Memory size up to 512M bytes.
•32MB to 256MB using 16Mb/32Mb/64Mb/128Mb/256Mb technology.
•Support for x8, x16 DRAM device widths.
•Supports single & double sided DIMMs.
•Unbuffered, Non-ECC SDRAM only Supported.
System BIOS
• Firmware Hub with security feature.
• PnP, APM, ATAPI and Windows® 95/98/2000.
• Full support of ACPI & DMI.
• Auto detects and supports LBA harddisks with capacities over 8.4GB.
• Easy to upgrade BIOS by end-user.
On-board I/O
• On board two PCI fast IDE ports supporting up to 4 ATA, ATA2 , Ultra DMA33/66/
100 IDE HDDs, CD-ROMs, ZIP drives and LS-120 drives as boot drive.
•Support Bus Master IDE, Read transfers up to 100MB/s, Writes to 89MB/s.
•OneECP/EPPparallelport.
•Two 16550 Compatible UART serial ports.
•One floppy port support two FDDs of 360KB, 720KB, 1.2MB, 1.44MB and
2.88MB capacity.
• Four USB ports.
• PS/2 keyboard connector.
•PS/2 mouse is supported.
•Infrared (IrDA) is supported via a header.
Plug-and-Play
• Supports Plug and Play specification 1.1.
• Plug and Play for DOS, Windows® 3.X, Windows® 95/98 as well as
Windows® 2000.
• Fully steerable PCI interrupts.
Hardware Configuration
4
Technical Reference Booklet
On-board GA (only for Intel®815E chipset)
•3D Hyper Pipelined Architecture.
•Full 2D H/W Acceleration.
•Motion Video Acceleration.
•Up to 1600x1200 in 8 bit Color at 85MHz Refresh.
•H/W Motion Compensation Assistance for S/W MPEG2 Decode.
•Software DVD at 30fps.
•Integrated 24-bit 230MHz RAMDAC.
Display Cache Interface multipexed on the AGP interface (only for
Intel® 815E chipset)
•32-bit data interface.
•133MHz SDRAM interface only.
•FlexibleAGPIn-Line Memory Module (AIMM) Implementation.
•Support for two 1Mx16,or one 2Mx32 on AIMM card.
•4MB max addressable.
On-board AC97 Sound (optional)
•Integrated AC97 controller with standard AC97 Codec.
• Direct Sound and Sound Blaster compatible.
•Full-Duplex 16-bit record and play back.
•PnP and APM 1.2 support.
•Win® 95/98, NT drivers ready.
•Line-in, Line-out, Mic-in and MIDI/Game port.
Power Management
• SupportsSMM,APMandACPI.
• Break switch for instant suspend/resume on system operations.
• Energy star “Green PC” compliant.
• Hardware monitoring circuit is supported, provide voltage, temperature, fan
speed, etc. monitoring (optional).
• WOL (Wake-On-Lan) header support.
• External Modem Ring-in Wake-up support.
Expansion Slots
• 1 CNR slot (shares 1 PCI slot).
• 1 AGP slot.
•4 PCI bus master slots - ver. 2.1 compliant (1 PCI shares with CNR slot).
CAUTION
Static electricity can harm delicate components of the motherboard. To prevent
damage caused by static electricity, discharge the static electricity from your
body before you touch any of the computers electronic components.
5
Hardware Configuration
Motherboard Layout
The following diagrams show the relative positions of the jumpers, connectors, major
components and memory banks on the motherboard.
NOTE
1) Be sure to check the cable orientation in order to match the colored strip to
the pin 1 end of the connector.
2) When you start up the system, please wait for 5 seconds after you power
on AC.
# The “VGA Connector” is installed for Intel®815E chipset version only.
6
Technical Reference Booklet
Jumper Settings
This chapter explains how to configure the motherboard’s hardware. Before using your
computer, make sure all jumpers and DRAM modules are set correctly. Refer to this
chapter whenever in doubt.
CPU Speed Selection
In this motherboard, jumperless feature is implemented such that no jumper is required to
be set for different type of CPU installed.
Notice:
1. Be sure to save the CMOS setting when exit the CMOS.
2. The CPU is frequency multiplier locked, no CPU speed change will be seen
even if the frequency multiplier setting in CMOS setup is changed.
CK1, CK4 - System Bus Frequency
CK1 CK4 CPU Clock Speed
Open Open 133MHz
Open Close 100MHz
Close* Close* Auto*
EDS1 - On Board AC97 Codec Sound
EDS1 Function
2-3* AC97 Sound Enable*
1-2 AC97 Sound Disable
JBAT - CMOS Clear
JBAT Selection
1-2* Normal*
2-3 CMOSClear
J SB1 - Keyboard Power Select
JVSB1 Select
2-3* Powered by +5V*
1-2 Powered by +5V Standby
(Allows Keyboard Power On)
CK1JVSB1
1JBAT
1
1
Close Open * = Default setting.
EDS1
CK4 1
1 1
1
1
1
7
Hardware Configuration
Pin Assignment
Internal Audio Connector
AUX1 : AUX-IN
Pin Assignment
1AUX-L
2 GND
3 GND
4AUX-R
CDS1 : CD-IN
Pin Assignment
1 CD-L
2 GND
3 GND
4 CD-R
1
1
R G L G
G L G R
CDS2 : CD-IN
Pin Assignment
1 CD-R
2 GND
3 CD-L
4 GND
CDS3 : CD-IN
Pin Assignment
1 GND
2 CD-L
3 GND
4 CD-R
FP1
FRONTPANELHEADER
HEADER 2x12
GND 24
KEYLOCK- 22
GND 20
18
KEYLOCK+ 16
14
12
IRTX 10
GND 8
IRRX 6
GND 4
SUS+ 2 SW -
PWR+
- SW
+SUS
LED -
PWR+
LED -
HDD+
SW -
RST+
+
-
NC
S
SPKER
IrDA
+
TX
-
RX
KEYLOCK
-
S
-
NC
+
23
21 GND
19
17 SPEAK
15 GND
13 RST+
11 HDDLED-
9 HDDLED+
7 PWRLED-
5 PWRLED+
3 GND
1 PWR+
X
VCC
X
X
VCC
8
Technical Reference Booklet
Clip
Clip
DIMM
DIMM Socket
Notch
Hardware etup
To Install DIMMs
1. Locate the DIMM sockets.
2. Holding the DIMM by the edges, remove it from its antistatic package.
3. Make sure the clips at either end of the socket are pushed away from the socket.
4. Position the DIMM above the socket. Align the two small notches in the bottom
edge of the DIMM with the keys in the socket.
5. Insert the bottom edge of the DIMM into the socket.
6. When the DIMM is seated, push down on the top edge of the DIMM until the retaining
clips at the ends of the socket snap into place. Make sure the clips are firmly in
place.
Turn system power off before installing and removing any
device, otherwise you’ll cause the system damage.
9
Hardware Setup
Installing a New Processor
An upgrade processor can dramatically increase general system speed and performance.
Most microprocessor upgrade kits include the following items:
• Microprocessor chip
• Installation instructions and technical data
Your system may have these features built in, or support them as upgrades.
To Install a Processor to ZIF Socket
To install the processor, follow these steps:
1. If the system microprocessor is already on the motherboard socket, you need to
remove it from the motherboard socket. The socket is a Zero Insertion Force (ZIF)
socketwhichhas a metal arm at one side. Carefully graspthisarm,moveit horizontally
away from the socket and lift it up. Eventually you will be able to lift the chip straight
up out of the socket. Be careful not to bend any pins.
Be careful not to bend any of the pins when removing the microprocessor
chip from its socket. The microprocessor chip can be permanently damaged.
2. Unpack the new microprocessor chip.
3. Carefully align the processor with the correct orientation to the socket on the
motherboard.
4. Carefully insert the processor into the socket, and move the metal arm downward to
replace it in its original position.
Connect the Processor Fan Connector
There is a fan attached the processor to prevent the overheating. Connect the
processor fan cable to the fan connector that located on the motherboard near the
processor and ensure the fan can operate. Otherwise the CPU can overheat and
cause damage to both CPU and motherboard.
Setting the Processor Speed
After you install the processor into the motherboard, set the processor speed by CMOS
setup.
10
Technical Reference Booklet
BIO etup
This chapter discusses Award’s Setup Program built into the ROM BIOS. The Setup
Program allows users to modify the basic system configuration. This special information
is then stored in battery-backed RAM, which retains the setup information when the
power is turned off.
Starting Setup
The Award BIOS is immediately activated when you turn on the computer. The BIOS
reads the system information contained in the CMOS and begins the process of checking
out the system and configuring it. When it finishes, the BIOS will seek an operating
system on one of the disks and then launch and turn control over to the operating
system.
While the BIOS is in control, the Setup Program can be activated :
1. By pressing <Del> immediately after switching the system on, or
2. By pressing the <Del> key when the following message appears briefly at
the bottom of the screen during the POST (Power On Self Test )
Press DEL to enter SETUP
If the message disappears before you can respond and you still wish to enter Setup,
restart the system to try again by turning it OFF then ON or pressing the “RESET” button
on the system case. You may also restart by simultaneously pressing the <Ctrl>, <Alt>,
and <Delete> keys. If you do not press the keys at the correct time and the system does
not reset, an error message will be displayed and you will again be asked to ...
PRESS F1 TO CONTINUE, DEL TO ENTER SETUP
Getting Help
Press F1 to pop up a small help window that describes the appropriate keys to use and
the possible selections for the highlighted item. To exit the Help Window press <Esc> or
the F1 key again.
In Case of Problems
If, after making and saving system changes with the Setup Program, you discover that
your computer does not reset, use the Award BIOS defaults to override the CMOS
settings.
Indice
Altri manuali V-tech Scheda madre
Manuali Scheda madre popolari di altre marche
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Manuale utente
Gigabyte
Gigabyte GA-9IVDT Manuale utente
Texas Instruments
Texas Instruments ADS8372EVM Manuale utente
Commell
Commell MS-C73 Manuale utente
IBT Technologies
IBT Technologies MB860 Manuale utente
Nvidia
Nvidia TEGRA DG-04927-001_V01 Manuale utente
