VADO IND-Z143 Series Manuale utente
1 way wall mounted concealed stop valve
Keep for future reference
Installation Guide
ZONE
Vado
Wedmore Road, Cheddar, Somerset, England BS27 3EB
tel 01934 744466 fax 01934 744345
aftersales@vado.com
www.vado.com
Version 2, 1-1-23
where inspiration flows
ZON-143-CP
ZON-143-H-CP
IND-Z143-☓☓☓
IND-Z143-H-☓☓☓
23
Please read these instructions carefully before starting installation and keep for future
reference.
Remove all packaging and check the product for missing parts or damage before
starting installation.
Any alterations made to this product and fittings may infringe water regulations and
will invalidate the guarantee.
The installation must comply with all Local/National Water Supply Authority
Regulations/Byelaws and Building and Plumbing Regulations.
To be installed in accordance with BS EN806.
We strongly recommend that you use a qualified and registered plumber.
General installation
Important - please read
When installed, the fitting must comply with the requirements of the Water Supply
(Water Fittings) Regulations 1999 and Scottish Byelaws 2004.
For further information, contact the Water Regulations department of your local water
supplier (see the WRAS website www.wras.co.uk for details) or the Water Regulations
Advisory Scheme by email (info@wras.co.uk) or telephone: 01495848454.
The fitting of an isolating valve to the inlet feed is advised for ease of maintenance.
Please take great care when installing this product not to damage its surface.
Please note if installing in an enclosed environment, access should be left for servicing
and maintenance. No costs relating to inadequate access can be accepted.
Contents of Packaging
Installation guide &
User manual Cover
Valve with Tiling Guide
Fixing nut, rubber washer and two screws
Collar
Extension rod with cap
Keep for future reference
Installation Guide
ZONE
1 way wall mounted concealed stop valve
4 5
Dimensions
78-113mm
52mm
121mm
1/2"
65mm
Ø57mm
80mm
2
1
45
Installation - Quick guide
3
x 2
113mm78mm
6 7
6
910
Installation - Quick guide
7
8
11
14 15a
Installation - Quick guide
12
13
- X mm
X mm
ZON-143-H-CP
ZON-143-CP
8 9
15b
Installation - Quick guide
16
17
Installation
Select the position for the shower valve and offer the shower valve to the wall, make
sure the valve is level and mark the 2 fixing points with a suitable pencil. Remove the
shower valve from the wall, drill the holes to a suitable depth for the wall plugs and
secure with suitable screws.
Valve
Tiling guide
Final wall surface
On opposite side
of tiling guide
Maximum 113mm
Fixing
screws
Minimum 78mm
Tiling
guide
Outlet arrow on
valve
Maximum
wall mark
Minimum
wall mark
=
x 2
1
2
3
2
1
3
11
10
Installation
Slide the collar into the hole. Line up the holes and secure in position using the screws
from the previous step.
Collar
Tiling guide
Installation
Tile around the tiling guide as tight as possible. Keep the final finished wall surface
between the min and max marks.
Outlet
Inlet from
ZON-128
Tiling guide
Outlet arrow on
valve
Screws
Screws
Remove the 2 screws using the suitable hex key provided with the ZON-128 and pullout
the tiling guide.
After removing the blanking plug and adding the outlet adaptor to the ZON-128 connect
the water supply to the right inlet of the valve. Connect the outlet (arrow on valve) to the
desired channel e.g. shower head and handset.
12
Installation
Insert the spacer plate into the step of the
collar.
There is a spacer plate incorporated into the end of the tiling guide. Remove this by
snapping it at the four points. Remove any burrs.
Tiling guide
Spacer plate
Step of collar
Extension rod
Spacer plate
Screw the extension rod onto the spindle
of the cartridge.
13
Installation
Measure the distance (X mm) the rod protrudes from the level of the spacer plate
and then unscrew the rod and remove the spacer plate. Note: Ensure the cartridge is
pushed in (the off position).
X mm
X mm
Rod
Spacer plate
Extension rod
Cap
Hex key
Screw the cap onto the rod until it's flush
and tighten the grub screw on the cap
using the smaller hex key provided with
the ZON-128.
Cut away the measured distance
from the end of the rod as well as the
2 screws
provided with the ZON-143 trim.
(X mm)
14
Installation
Apply a thin bead of silicone between
the collar and the tiles.
Screw the cover onto the fixing nut. Cover orientation
Place the screws inside the fixing nut on
opposite sides
15
Installation
With the correct cover orientation, use
the screws to locate the holes in the valve
body.
Fit the rubber washer, place the button onto the cap of the extension rod and screw the
rod onto the spindle of the cartridge.
Make sure the cover is level and tighten
Cover
Button
x 2
Cover
Rubber
washer Cap
13
2
ZON-143-CP
ZON-143-H-CP
the screws using the suitable hex key
provided with the ZON-128 to secure the
cover.
Questo manuale è adatto per i seguenti modelli
3
Indice
Altri manuali VADO Unità di controllo
VADO
VADO geo Istruzioni per l'installazione e il funzionamento
VADO
VADO Axces AX-VAL-149-CP Manuale di istruzioni
VADO
VADO celsius Istruzioni per l'installazione e il funzionamento
VADO
VADO AXCES SIRKEL AX-SIR-149T-CP Manuale di istruzioni
VADO
VADO ALTITUDE Manuale utente
VADO
VADO AX-EKO-145-CP Manuale di istruzioni
VADO
VADO NOTION TAB-128/3WO-NOT-CP Manuale utente
Manuali Unità di controllo popolari di altre marche
Festo
Festo Compact Performance CP-FB6-E Manuale elenco delle parti
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuale utente
JS Automation
JS Automation MPC3034A Manuale utente
JAUDT
JAUDT SW GII 6406 Series Guida rapida
Spektrum
Spektrum Air Module System Manuale utente
BOC Edwards
BOC Edwards Q Series Manuale utente
