VALCOBABY ION Manuale di installazione e funzionamento

Thank you for purchasing a quality VALCO BABY product. Please read and follow the instructions outlined in

this guide carefully. Familiarise yourself with the construction and safety features; be sure that you understand

all the warnings and safety guidelines before use.

Important: Please read the following instructions carefully before assembling this product. Retain this

guide in a safe place for future reference.

PRODUCT REFERENCE GUIDE

STROLLER

Due to our policy of continuous

product development, this product

is constantly evolving. It is possible

that some features or procedures

outlined here have changed since

this document was written. If you are

unsure of any procedure shown here,

please contact us via the web at

[email protected] to obtain the most

up to date information before use.

Include the batch number, which can

be found on a sticker on the frame.

All pictures and diagrams herein are

provided for illustration purposes only.

Actual product, colour or fabric may

vary. VALCO BABY reserves the right

to modify or alter any specication

or colour without notice or obligation

to modify any product previously

purchased

ION

VE 2012

vs100412

FURTHER INFORMATION:

www.valco.com.au

Find us on:

OPENING

Remove the stroller from the carton and

dispose of all packaging thoughtfully.

FIGURE A

1. Lift your stroller handle upward. You will

feel the stroller chassis opening.

FIGURE B

2. Continue unfolding the chassis until you

hear the chassis click open in the locked

position.

INSERTING REaR axLE

FIGURE C

1. Align the plastic housings of the silver

brake section with the open tubes of the

rear of the stroller chassis.

2. Insert the housings over the open tubes

until the brake section locks securely into

place. IMPORTANT: Test that the brake

section is securely engaged onto the

stroller frame by pulling on it rmly.

INSERTING bUmPER baR

FIGURE D

1. Align the plastic housings of the bumper

bar with the housing on the sides of the

stroller chassis.

2. Slide the bumper bar into the housing

along the housing tracks until it locks into

place.

3. Repeat procedure for the second bar on

the other side of the stroller.

4. Pull the sides of the seat fabric, and the

crotch strap over the bumper bar and

snap into position.

5. To remove the bumper bar, unsnap the

crotch strap and the seat sides from the

bumper bar.

6. Lift both bumper bar latches found

on the underside of the each side

of the bumper bar housing, while

simultaneously lifting the bumper bar to

slide it free.

INSERTING REaR whEELS

FIGURE E

1. Simultaneously press on the spring

loaded axle button and insert it

through the central hub of the rear

wheel. Repeat this process for the

other rear wheel.

FIGURE F

2. Pressing the axle button again, insert

the axle end into the side of the brake

housing as far as it will go. Release

the axle button and pull slightly on the

wheel to ensure that it has securely

engaged.

INSERTING ThE FRONT whEELS

FIGURE G

1. Grasping the front wheel by the shaft,

align the shaft with the hole in the

underside of the swivel housing.

2. Insert the shaft into the housing

as far as it can go until it engages

securely.

3. Repeat the procedure for the other

front wheel.

IMPORTANT: Pull the wheel

downward to test that it has securely

engaged in the housing.

SECURING ThE FRONT whEELS

FIGURE H

1. Your front wheels can be set to swivel

freely (360º) or can be xed in place

for use over rough or sandy surfaces.

2. To x the front wheel in the non

swivel position, turn the wheel so that

the two notches on both housings line

up. Press down rmly on the swivel

lock until it locks into place.

3. To unlock simply lift the locking tab

until it locks in the open position.

aDJUSTING ThE haNDLE

FIGURE I

1. Your handle has been ergonomically

designed to provide a truly

comfortable ride for parents and

guardians of all heights.

2. To adjust your handle, simultaneously

press the two release buttons on

either side of the handle, moving it to

the desired position.

USING YOUR bRaKE SYSTEm

FIGURE J

1. To engage the brake press down on

the central red brake pedal, at the tab

that is closest to you.

2. To disengage, simply reverse the

process

IMPORTANT WARNING: Always

test that the brakes are fully

engaged by pushing the stroller

forward and backward.

aTTaChING YOUR baSKET

FIGURE K

1. Locate the webbing channels found

on either side under the seat.

2. Thread each basket wire through the

webbing channels.

3. Hook the wire end over the side of

the opening at the end of the webbing

channel.

TEThER STRaP

FIGURE L

1. Your stroller has been equipped with

a safety tether strap. This strap has

been designed to always keep your

stroller within constant reach.

NOTE: The tether strap doubles as

your locking strap (Figure O).

IMPORTANT: ALWAYS SLIP THE LOOP

IN THE STRAP SECURELY OVER YOUR

WRIST WHENEVER A CHILD IS IN

YOUR STROLLER.

FOLDING YOUR STROLLER

FIGURE M

1. Push hood back against the frame.

2. To fold your stroller, turn the release

key clockwise and push the handle

forward releasing the stroller frame

slightly.

FIGURE N

3. Lift the secondary locking latch clear

of the plastic frame catch. This latch

is spring loaded and you may need to

hold it open as you push the handle

forward.

4. Push the handle forward.

Tether

Strap

Lock

Strap

INSERTING REaR axLE

FIGURE O

5. Continue to fold the frame forward.

Make sure that the lock strap is

threaded through handlebars

FIGURE P

6. To lock the frame, the keyhole of the

lock strap should be engaged over

the locking pin found on the frame

chassis behind the front wheel. Click

securely into place.

HINT: ADJUST THE HANDLE 180°

BACKWARD TO CREATE THE

SMALLEST FOLD

FIGURE Q

The Expanda hood unzips, increasing

the size of your standard hood to give

greater coverage and protection from

the sun and weather for your child.

To open the Expanda Hood:

1. Locate the zip in the center of the

Expanda Hood and unzip completely.

Gently pull the Expanda Hood forward

until it is reaches its full extension.

To close the Expanda Hood:

2. Gently push the Expanda Hood back,

allowing the middle section to fold in

on itself. Carefully zip the Expanda

Hood closed.

IMPORTANT: ALWAYS TAKE CARE WHEN

CLOSING THE EXPANDA HOOD TO

AVOID THE ZIPPER CATCHING ON THE

ENCLOSED FABRIC

USING YOUR haRNESS

FIGURE R

Your stroller harness is specifically designed

with many built in safety features.

This includes the requirement that, when

opened, all straps are released so that no

dangerous loops can be formed causing a

strangulation hazard.

WARNING: YOUR CHILD MUST ALWAYS BE

HARNESSED WHEN IN THE STROLLER

Closing your harness: Slide each of the

shoulder strap bottom guides (1) into the

corresponding channel on the top of each

side strap prong.

Insert each completed prong into the central

buckle housing (2).

Carefully adjust the harness straps to snugly

fit your child by adjusting the sliders (3)

located on each strap. The harness should

be fitted to your child’s body, tight enough

so that they cannot wriggle free of the straps

but, loose enough, so as not to cause any

discomfort.

For even more flexibility, the height at which

your shoulder straps are fitted to the stroller

can be adjusted at 3 points.

To change the shoulder strap position:

From the rear of the seat, thread the top of

the strap back through the harness slot (26)

by manoeuvring the locking ring so that it

fits through the slot.

Rethread the strap back through the desired

slot from the front of the seat

Opening your harness:

Press the central housing button (4).

This will release both side prongs from the

central housing. The shoulder and waist

straps will release automatically from each

other.

If the shoulder and waist straps do not

automatically disengage from each other,

manually slide the guides of the waist

channels. Your harness will separate into 5

sections.

IMPORTANT WARNING: WHEN NOT IN

USE, BE SURE THE SHOULDER AND WAIST

STRAPS ARE ALWAYS DISCONNECTED

FROM THE CENTRAL HOUSING AND

EACH OTHER.

FURTHER INFORMATION:

www.valcobaby.com.au

Find us on:

WARNING: TO AVOID INJURY OR DEATH











! 

! 







•NEVER USE ON STAIRS OR ESCALATORS.









! .























.











Should the chassis become wet, dry off promptly before storing. If this pram is used near the ocean or salted roads, spray the chassis

and seat frame with water and dry. We recommend a rust inhibiting product should be used to prevent rust and fatigue on metal

parts.



near the beach or in a dusty environment you must wipe down the axles and wheels then lubricate them monthly.





Indice

Altri manuali VALCOBABY Passeggino

VALCOBABY

VALCOBABY ZeeTwo Manuale utente

VALCOBABY

VALCOBABY Latitude Manuale di installazione e funzionamento

VALCOBABY

VALCOBABY RunAbout Tri-mode series Manuale di installazione e funzionamento

VALCOBABY

VALCOBABY Zee Manuale di installazione e funzionamento

VALCOBABY

VALCOBABY REBEL Q Manuale di installazione e funzionamento

VALCOBABY

VALCOBABY BASSINET Manuale utente

VALCOBABY

VALCOBABY VEEBEE CO-RIDER Manuale utente

VALCOBABY

VALCOBABY BUGGSTER BASSINET Manuale di installazione e funzionamento

VALCOBABY

VALCOBABY Vee Bee Dash Manuale di installazione e funzionamento

VALCOBABY

VALCOBABY SPARK DUO Manuale di installazione e funzionamento

VALCOBABY

VALCOBABY ZEE Manuale di installazione e funzionamento

VALCOBABY

VALCOBABY prism Manuale di installazione e funzionamento

VALCOBABY

VALCOBABY RAD Manuale di installazione e funzionamento

VALCOBABY

VALCOBABY trend duo Manuale di installazione e funzionamento

VALCOBABY

VALCOBABY ORION Manuale di installazione e funzionamento

VALCOBABY

VALCOBABY Tri-Mode Twin Manuale di installazione e funzionamento

VALCOBABY

VALCOBABY snap ultra Manuale di installazione e funzionamento

VALCOBABY

VALCOBABY EVO2 for 2 Manuale di installazione e funzionamento

VALCOBABY

VALCOBABY Vee Bee SCOUT Manuale di installazione e funzionamento

VALCOBABY

VALCOBABY REBEL Q Manuale di installazione e funzionamento

VALCOBABY

VALCOBABY VEEBEE DOUBLETAKE Manuale di installazione e funzionamento

VALCOBABY

VALCOBABY VEE BEE LIO Manuale di installazione e funzionamento

VALCOBABY

VALCOBABY EZ Rider Manuale di installazione e funzionamento

VALCOBABY

VALCOBABY Runabout Series Manuale di installazione e funzionamento

Manuali Passeggino popolari di altre marche

Hauck

Hauck Priya Trioset Manuale utente

CHILDHOME

CHILDHOME CWQDN Manuale utente

Dreamer Design

Dreamer Design Rebound GST Manuale utente

Britax

Britax STEELCRAFT AGILE Manuale utente

Graco

Graco 7427 Manuale utente

Comfort

Comfort COMPASS Manuale utente

OBaby

OBaby Aura Manuale utente

Tutek

Tutek Tirso Manuale utente

Babify

Babify Dual Plus Manuale utente

Graco

Graco Stroller Manuale utente

Special Tomato

Special Tomato Jogger Manuale utente

Chicco

Chicco CORTINA TOGETHER TWO-PASSENGER STROLLER Manuale utente

Otto Bock

Otto Bock Kimba neo Manuale utente

Milly Mally

Milly Mally ROYAL Guida rapida

Hauck

Hauck DUETT 3 PRAM Manuale utente

BOB

BOB DUALLIE Manuale utente

Nuna

Nuna Pepp Manuale utente

Britax

Britax B2 Manuale utente