Valor PORTRAIT Manuale utente

4002418-07

569 Ledge Front

INSTALLATION INSTRUCTIONS

CSA approved for use with Valor Models 530I Heaters ONLY

Notes: This kit must be installed or serviced by a qualiﬁed

installer, service agency or gas supplier. These instructions are to

be used in conjunction with the main installation instructions

for Valor heater model 530I.

The installation of this kit affects the framing and method of

installing the 530 heater.

Installation Sequence

1. Frame the cavity.

2. Install the heater with stud brackets, stand-offs, insulation, wall switch

kit, and cement board.

3. Gas ﬁt and vent heater.

4. Drywall only (no tile, etc.).

5. Assemble and install the mounting frame.

6. Install ﬁnishing material (tile, etc.). Finish around or under 570 Finishing

Plate if using it.

7. Install the trim panel ﬁtted with the barrier screen.

INSTALLER

Leave this manual

with the appliance.

CONSUMER

Retain this manual

for future reference.

HOT GLASS WILL

CAUSE BURNS.

DO NOT TOUCH GLASS

UNTIL COOLED.

NEVER ALLOW CHILDREN

TO TOUCH GLASS.

WARNING

A barrier designed to reduce the risk of burns from the hot viewing

glass is provided with this appliance and shall be installed

for the protection of children and other at-risk individuals.

PORTRAIT

530 engine

Touch control

wall switch

Roof

grille

panel

Stand-off

Insulation

Stud bracket

Convection bafﬂe

Mounting

frame

Window frame cover

Cement board

Trim panel —patina, brushed nickel or black—

with barrier screen

570FPB Finishing Plate

(530 engine and 570FPB Finishing Plate sold separately)

Overview

570 Finishing Plate

sold separately

Cement board

center

of vent

11/16”(17 mm) between

bottom of engine and

bottom of trim

570 plate thickness: 1/2” (13 mm)

Min. 36” (0.9 m) to

combustible materials

27-3/8”(696 mm)

31-1/8”(790 mm)

30”(762 mm)

36-1/2”(927 mm)

21-5/8”(549 mm)

25-1/4”(641 mm)

30-1/4”(768 mm) to header base

31”(787 mm) to cement board top

4”(102 mm) between

bottom of engine and

bottom of 570 plate

bottom of 570

bottom of trim

1/2”(13 mm) min.

under bottom of

trim for air gap

3-5/16”(84 mm)

cement board

and drywall

thickness:

1/2” (13 mm)

wall nish thickness

over top of drywall:

max 1” (25 mm),

1/2” (13 mm)

when using 570 Plate

6-5/8” (168 mm) dia.

3-5/8”

(92 mm)

7-1/8”

(181 mm)

2”

(51 mm)

22-1/2” (572 mm)

47-15/16” (1216.9 mm)

Face of

wall studs

33-15/16” (861.3 mm)

11-15/16”

(302.5 mm)

20” (508 mm)

12-3/4”

(324 mm)

surface

of wall

nish

2” (51 mm) sidewall

minimum clearance

90°

Dimensions & Clearances

Mantel Clearances A

Combustible

mantel

Face of

cement

board/

drywall

Mantel Depth ‘A’ 0–6”

(0–152 mm) 8”

(203 mm) 10”

(254 mm) 12”

(305 mm)

Mantel Height ‘B’ 4”

(102 mm) 8”

(203 mm) 10”

(254 mm) 12”

(305 mm)

Side View

Framing

Wall Finish

30-1/4”(768 mm)

to header

27-3/8”(695 mm) to

cement board

3-5/8”(92 mm)

cement board

supplied

22-1/2”min.

(572 mm)

Wall Finish

This is the framing

width. Drywall to

23-3/4”(603 mm) wide.

Minimum 12-3/4” (324 mm)

(Allow extra for rear vent elbow)

drywall

570 plate outline

wall nish must be

non-combustible

at top of opening

gap must

remain open

for air ow

cement board

23-3/4” (603 mm)

25” (635 mm)

WALL

FINISH no 570

plate

with 570 ﬁnishing plate

tile up to

plate: tile behind

plate:

Tile or ﬁnish

thickness 1-1/8”

(30 mm) 1-3/8”

(35 mm) 5/8”

(18 mm)

Drywall 1/2” (12.7 mm)

Installation

1. Fit the stud brackets

to the appliance’s

sides (2 screws/

side). Make sure the

horizontal tabs are at

the top.

2. Fit the convection

bafﬂe to the top of

the appliance case

(2 screws). The

convection bafﬂe

slips under the top of

the appliance case.

3. Required for

installation

in combustible

construction. Bend

the stand-offs into

shape and ﬁx them to

the appliance’s case

as indicated (4 screws/

side, pre-ﬁtted on

engine).

4. Required for

installation in

combustible

construction. Add

insulation pad on the

top of the appliance,

cutting around the pipe

if installing a top vent.

5. Mount the appliance

to the studs with

wood screws (2/side,

not supplied). Make

sure the framing is

leveled.

6. Proceed with the

installation of the

ﬁrebox, gas ﬁtting,

venting and so on

as per appliance

instruction manual.

Grille inserted

parallel to

ﬁrebox edge

LOGS & ROCKS VERSIONS ONLY. Grille cannot

be used with coal fuel bed version. Install the grille

panel inside the appliance:

a. Insert the grille in the ﬁrebox by aligning one

of its side edge to the edge of the ﬁrebox as

indicated.

b. Raise the grille up

to cover the top

ﬁrebox ports

and hold with

one hand.

Note: The port

cover strip

supplied with

the heater is not

required.

c. Place the rear

brick wall. It

should support

the grille. If not,

keep holding it

while you place

the side brick

walls. Refer to

the ﬁreplace

installation manual for more information on

installing the brick walls.

7. Install Touch control wall switch. The wall switch

comes with a 26-foot wire and a cover plate. The

switch is connected to the receiver in the ﬁreplace.

The receiver is located left of the control valve

under the burner module.

a. Decide where the switch is to be installed. Install

an electrical outlet box (not supplied).

b. Thread the switch wire through an access hole

in the appliance.

CAUTION

DO NOT PUT BATTERIES IN THE REMOTE

CONTROL RECEIVER until the wires are

connected to the burner control unit as short-

circuit could result in the destruction of the

electrical components.

CAUTION

Do not run the switch wire over the top of the

ﬁrebox. Route the wire so it does not contact the

ﬁrebox.

tab at

the top

Cement

board

Drywall opening

31”

(787 mm)

23-3/4”

(603 mm)

c. Pull out the receiver box. Remove the batteries

from the receiver box if it contains any. You

can remove the ignition wire to improve access

to the receiver.

d. Take the switch wire and plug it into the

receiver’s connection slot as indicated (the other

slot should already be ﬁtted with the valve’s wire

harness connector). See diagram at right.

IMPORTANT: The

connection can only be

done one way. Do not

force it or damage the

pins!

e. On the outside of the ﬁreplace, run the switch

wire into the outlet box.

f. Plug the wire into the switch plate and to the

outlet box.

g. Reconnect the ignition wire to the receiver if it

was previously removed.

h. Insert 4 AA batteries in the receiver. Replace the

cover.

i. Test the operation of the wall switch.

j. Fix the wall cover plate to the outlet box.

k. Replace the receiver in its position and as well

as the antenna if deployed.

8. Install the cement

board on top of the

appliance. The board

sits on the horizontal

tabs at the top of the

stud brackets.

9. Install the drywall at this point. Although it can be

installed later, the mounting frame for the front will

overlap it.

Wall opening: 23-3/4” (w) x 31” (h)

Note: If tiling, etc. is used overtop of drywall,

complete steps 10, 11, and 12 ﬁrst as the frame,

once installed, will deﬁne where to tile up to.

CAUTION

DO NOT USE a screwdriver or other metallic object to

remove the batteries from the receiver or the handset!

This could cause a short circuit to the receiver.

CAUTION

To avoid short-circuit to the receiver, position the antenna

so that it DOES NOT TOUCH the ignition wire.

Ignition Wire

Connection

(spade type

connector)

Be careful when

removing and

reinstalling: not to

bend or break the

spade connector

Ignition Wire

Antenna

Valve Wire

Harness

Wall Switch

Harness

10. Assemble the mounting frame following the steps

indicated below.

a. Fix the bottom piece to the two side pieces as

indicated below (2 screws/side).

b. From outside of the frame, ﬁx the top piece to

the left side piece with the tabs inboard of the

side piece (2 screws).

c. Slide the internal bafﬂe over the screw tips on

the frame’s left piece, under the top piece. Hold

the bafﬂe in place with one hand.

d. With the other hand, align the right holes of

the bafﬂe to the holes in the top piece and the

frame’s right piece. Fix the three pieces together

from the outside with all tabs inboard (2 screws).

NOTE: All the side tabs of the bottom, top,

and internal bafﬂe pieces should be inboard

of the frame.

Bottom piece orientation—right side view

Front

Fixing points

Internal bafﬂe orientation—

right side view

Front

Screw tip

Frame top

Frame bottom

Frame—right

side view

No tabs showing

on outside surface

WARNING

DO NOT TOUCH THE BARRIER SCREEN OR

FIREPLACE WHILE THEY ARE HOT!

Let the

ﬁreplace cool ﬁrst before cleaning it.

FOR SAFETY PURPOSE, ensure the barrier

screen is re-installed on the ﬁreplace front after

maintenance if it has been removed.

WARNING

Window frame

cover—rear view

Top

11. Slide the mounting frame over the appliance case.

The front of the frame has 4 screws protruding from

it. Fix the frame to the stud mounting panels on

each side of the appliance (3 screws per side).

12. Apply wall ﬁnish on top of drywall.

IMPORTANT: The drywall is assumed to be

1/2 inch thick.

Wall ﬁnish material thickness on top of drywall

such as tile, brick, and so on:

When ﬁnishing under optional 570 Plate:

1/2 inch maximum.

When ﬁnishing around optional 570 Plate:

see mantel clearances if ﬁnish protrudes from plate.

Without 570 Plate: 1-1/8 inch maximum.

13. Hook the window trim cover on the top edge of the

window frame.

14. Hook the front trim to the mounting frame placing

its keyholes on the protruding screws on the front

face of the mounting trim and slide it downward to

ﬁt it.

Maintenance

To clean the front trim, use mild soap and water. You

can dust the screen with a soft brush. To brush the

back of the screen, simply unhook the front trim.

If the barrier becomes damaged, the barrier shall

be replaced with the manufacturer’s barrier for this

appliance.

To clean the window and ceramics inside the ﬁrebox,

consult the Owner’s Information section of the

Installation and Owner’s Manual supplied with the

ﬁreplace.

DO NOT CLEAN THE GLASS WINDOW WITH

AMMONIA!

Wiring Diagram

Touch Control Wall Switch

Connector

Repair Parts List

Description Part Numbers

569LFP Patina 569LFN Nickel 569LFB Black

1 Trim Panel 4002267PA 4002267N 4002267AZ

2 LH Side Lead-in Panel 4002268AZ 4002268AZ 4002268AZ

3 RH Side Lead-in Panel 4002269AZ 4002269AZ 4002269AZ

4 Lower Lead-in Panel 4002270AZ 4002270AZ 4002270AZ

5 Cement Board 4002568 4002568 4002568

6 LH Column Assembly 4002272 4002272 4002272

7 RH Column Assembly 4002274 4002274 4002274

8 Bottom Panel 4002282AZ 4002282AZ 4002282AZ

9 Roof Grille 4002101EB 4002101EB 4002101EB

10 Internal Bafﬂe 4002402 4002402 4002402

11 Top Panel 4002276AZ 4002276AZ 4002276AZ

12 Window Frame Cover 4002279BY 4002279BY 4002279BY

13 Convection Bafﬂe 4002277BY 4002277BY 4002277BY

14 Touch Control Wall

Switch with wire 4001487 4001487 4001487

15 LH Stud Bracket 4002516 4002516 4002516

16 RH Stud Bracket 4002517 4002517 4002517

17 LH ZC Stand-off 4002570 4002570 4002570

18 Insulation 620B987 620B987 620B987

19 RH ZC Stand-off 4002569 4002569 4002569

20 Barrier Screen 4003375 4003375 4003375

Screws 8 x 3/8 (20) 100A757 100A757 100A757

Nuts 8 x 32 (4) 4001517 4001517 4001517

11 12 13

Designed and Manufactured by / for

Miles Industries Ltd.

190 – 2255 Dollarton Highway, North Vancouver, B.C., CANADA V7H 3B1

Tel. 604-984-3496 Fax 604-984-0246

www.valorﬁreplaces.com

Because our policy is one of constant development and improvement, details may vary slightly from those given in this publication.

Questo manuale è adatto per i seguenti modelli

Indice

Lingue:

Altri manuali Valor Accessori per caminetti

Valor

Valor 555CFK Manuale utente

Valor

Valor LEGEND G3 763BPB Manuale utente

Valor

Valor L3 Manuale utente

Valor

Valor H5 Manuale utente

Valor

Valor G3.5 Series Manuale utente

Valor

Valor 716EHC Manuale utente

Valor

Valor L1 Series Manuale utente

Valor

Valor LX2 Series Manuale utente

Valor

Valor LEGEND G3.5 Manuale utente

Valor

Valor Madrona BSKMF01 Manuale utente

Valor

Valor LX2 Series Manuale utente

Valor

Valor 546LFB ZC Portrait Ledgeview Front Manuale utente

Valor

Valor 546LFB ZC Portrait Ledgeview Front Istruzioni per l'installazione

Valor

Valor G3.5 Series Manuale utente

Valor

Valor L1 Series Manuale utente

Valor

Valor L1 Series Manuale utente

Valor

Valor PORTRAIT BSK563 Manuale utente

Valor

Valor G3 Series Manuale utente

Valor

Valor L1 Series Manuale utente

Valor

Valor LT1 2500K Manuale utente

Valor

Valor Portrait Series Manuale utente

Valor

Valor G3 Series Manuale utente

Valor

Valor G4 791STB Manuale utente

Valor

Valor LEGEND G3.5 Manuale utente

Manuali Accessori per caminetti popolari di altre marche

Exodraft

Exodraft Xzense Manuale utente

Whalen

Whalen Ruso MNFP62BF23-6 Manuale utente

Lopi

Lopi Hearthview 864 Manuale utente

Woodstock Soapstone

Woodstock Soapstone Fireview 201 Manuale utente

EdilKamin

EdilKamin SERBATOIO 250 Guida rapida

Bronpi

Bronpi KIT-1 Manuale utente

Town & Country Fireplaces

Town & Country Fireplaces 22150051 Manuale utente

Travis Industries

Travis Industries 33 DVI Manuale utente

Superior

Superior ASD3628-TI Manuale utente

pleasant hearth

pleasant hearth OFP28WG Manuale utente

IHP

IHP Astria Series Manuale utente

Firegear

Firegear FG-H-2110SS Manuale utente

Nibe

Nibe Contura C i31 Manuale utente

kozy heat

kozy heat KZK-052 Manuale utente

SimpliFire

SimpliFire SF-WM36 Manuale utente

Bluegrass Living

Bluegrass Living BC18NR Guida rapida

pleasant hearth

pleasant hearth IRIS SCROLL Manuale utente

Cooke

Cooke Glass Wind Guard Manuale utente