VDH FC 3500 DC Manuale utente

Description: FC 3500 DC Pages: 23 Doc.no: 150304

Type: Manual By: BVDB Version: 1.2

File: Do150304 FC 3500 DC V12 EN.docx Initials: Date: 15-04-2015

VDH Products BV

Manual FC 3500 DC

Fan Control

FC 3500 DC Fan Control Document no.:150304 Version: 1.2

Page 2of 23

Table of contents

1Introduction......................................................................................................................................................... 3

1.1 Overview FC 3500 DC System................................................................................................................ 3

1.2 Warning ....................................................................................................................................................... 4

2Safety Instructions............................................................................................................................................ 5

2.1 Electric Shock Prevention....................................................................................................................... 5

2.2 Fire Prevention .......................................................................................................................................... 5

2.3 Injury Prevention....................................................................................................................................... 5

2.4 Additional Instructions............................................................................................................................ 6

3Technical Data.................................................................................................................................................... 9

4Installation.........................................................................................................................................................10

4.1 Unpacking the FC 3500 DC unit..........................................................................................................10

4.2 Installation of the FC 3500 DC ............................................................................................................10

5Control................................................................................................................................................................11

5.1 Switching the control-unit on or off..................................................................................................11

5.2 Adjusting the temperature set point .................................................................................................11

5.3 Adjusting the fan speed ........................................................................................................................12

5.4 Adjusting the fan speed without temperature control .................................................................12

5.5 Viewing other measurements..............................................................................................................12

6Programming Parameters ............................................................................................................................13

6.1 Parameter table ......................................................................................................................................14

6.2 Night temperature offset (P70)..........................................................................................................18

7Error codes ........................................................................................................................................................18

7.1 Trouble shooting .....................................................................................................................................18

8Installation.........................................................................................................................................................19

8.1 Connection FC 3500 DC drawing 150182w0...................................................................................19

8.2 Block diagram FC 3500 DC drawing 150201w1.............................................................................20

8.3 Dimensions FC 3500 DC........................................................................................................................21

Appendix-A: FC 3500 BP display panel...............................................................................................................22

FC 3500 DC Fan Control Document no.:150304 Version: 1.2

Page 3of 23

1Introduction

This document describes the working and control of the Heinen & Hopman FC 3500 DC.

The system can consist of the following parts:

1) FC 3500 DC: Main Panel

2) FC 3500 BP: Display-unit several types (Four button control)

3) FC500-sens: Temperature sensors (Water- Air- en Outside-sensor)

4) RH95-2: Humidity sensor (For Humidity control see Parm.35).

1.1 Overview FC 3500 DC System

FC 3500 DC Fan Control Document no.:150304 Version: 1.2

Page 4of 23

1.2 Warning

It is highly recommended to study the operation of

the FC 3500 DC Fan Control system carefully

before using it.

Disclaimer

The information contained in this document is assumed to be accurate.

However VDH Products BV accepts no liability for any mistakes or errors.

reproduced without the prior written permission of VDH Products BV.

Edition

v1.0 1st pre-release edition 31-03-2015

v1.1 changed frontview and connections to general 01-04-2015

v1.2 changed connections 15-04-2015

FC 3500 DC Fan Control Document no.:150304 Version: 1.2

Page 5of 23

2Safety Instructions

2.1 Electric Shock Prevention

WARNING

While power is on or when the FC 3500 DC is running, do not open the top cover of the

housing. You may get an electric shock.

·Do not run the FC 3500 DC with the top-cover removed. Otherwise, you may access the

exposed high-voltage parts and get an electric shock.

·Before starting wiring or inspection, switch power off, wait for more than 1 minutes.

·Ground the FC 3500 DC.

·Any person who is involved in the wiring or inspection of this equipment should be fully

competent to do the work.

·Always install the FC 3500 DC before wiring. Otherwise you may get an electric shock or be

injured.

·Operate only with dry hands to prevent an electric shock or be injured.

·Do not subject the cables to scratches, excessive stress, heavy loads or pinching.

Otherwise, you may get an electric shock.

·Do not change anything while power is on. It is dangerous to change while the power is on.

2.2 Fire Prevention

CAUTION

Mount the FC 3500 DC on an incombustible surface. Installing the equipment directly on

or near a combustible surface could lead to a fire.

·If the FC 3500 DC has become faulty, switch off the FC 3500 DC power.

·Mount the FC 3500 DC in ventilated area’s only.

2.3 Injury Prevention

CAUTION

Apply only the voltage specified in the instruction manual to each terminal to prevent

damage.

·Ensure that the cables are connected to the correct terminals. Otherwise, damage may

occur.

·Always make sure that polarity is correct to prevent damage.

FC 3500 DC Fan Control Document no.:150304 Version: 1.2

Page 6of 23

2.4 Additional Instructions

Also note the following points to prevent an accidental failure, injury, electric shock, etc.

Transportation and Installation

CAUTION

Ensure that installation position and material can withstand the weight of the FC 3500

DC. Install according to the information in the Instruction Manual.

·Do not operate if the FC 3500 DC is damaged or has parts missing.

·Do not stand or rest heavy objects on the FC 3500 DC.

·Prevent screws, wire fragments or other conductive bodies or oil or other flammable

substance from entering the FC 3500 DC.

·Place during installation a covering plate over the FC 3500 DC to prevent metal powder,

from drilling activity, being fallen into the unit. Remove covering plate always after

finishing installation otherwise, it will give a negative effect on the ventilation of the unit.

And the unit can even be overheated by it.

·Do not drop the FC 3500 DC or subject it to impact.

·Use the FC 3500 DC under the environmental conditions given in the technical data.

Wirring

CAUTION

Use only cables and wiring capable of withstanding temperatures of ≥70OC.

·It is recommended to use insulation-sleeved solderless terminals for power supply, heater,

valve and fan wiring.

·Connect wires only when the unit is switched off.

·Any person who is involved in the wiring or inspection of this equipment should be fully

competent to do the work.

·Check if the nominal supply voltage from the FC 3500 DC is equal to the AC-supply

voltage. A incorrect power supply voltage can lead to fire, injury or failure.

·Place interrupters, capable of switching off frequency controllers, like automatic-MCCB-

fuses, between the power supply and the FC 3500 DC and take other safety actions to

prevent short-circuit in the external wiring. If no safety action is installed, this can lead to

fire, injury or failure.

·Take care for correct wiring which is firmly mounted otherwise measurement mismatch,

injury or damage to the unit can occur.

·Do not connect a AC supply to the outputs terminals of fan, heater or water valve. This can

lead to damage or failure of the unit.

FC 3500 DC Fan Control Document no.:150304 Version: 1.2

Page 7of 23

WARNING

Do not attach signal-data cables (display, RS485, sensors, I/O, etc.) to live cables, antenna

cables or cables with interference signals.

·Distance between signal-data cables and cables with interference should be more than

30cm but the absolute minimum should be 10cm.

·Better is to have separate cable channels for signal-data cables and cables with

interference signals (Cable channels with separation must be in full metal).

Trial Run

CAUTION

·Check all parameters, and ensure that the machine will not be damaged by a sudden start-

up.

Emergency Stop

CAUTION

·Provide a safety backup such as an emergency brake which will prevent the machine and

equipment from hazardous conditions if the FC 3500 DC fails.

Operation

WARNING

Do not modify the equipment

·The electronic over-current protection does not guarantee protection of the motor from

overheating.

·Do not use a magnetic contactor on the FC 3500 DC input for frequent starting/stopping

of the FC 3500 DC.

·Before changing the settings of the FC 3500 DC fully examine the performances of the

motor.

·Before running a FC 3500 DC which had been stored for a long period, always perform

inspection and test operation.

·For a good performance the FC 3500 DC must be installed in a room which is not applied

to extreme temperature changes.

·When the FC 3500 DC is mounted in a closed switchboard panel this panel should have a

cooling fan or airco to provide an ambient temperature of maximum 40oC.

·The case temperature of the FC 3500 DC may be 30/C higher than the ambient

temperature.

FC 3500 DC Fan Control Document no.:150304 Version: 1.2

Page 8of 23

Maintenance, Inspection and Parts Replacement

CAUTION

Check the environment of the FC 3000 DC regularly, to obtain good working conditions.

·Do not carry out a megger (insulation resistance) test on the control circuit of the FC

3500 DC.

·Replace parts only when the FC 3500 DC is switched off, wait 10 minutes and then open

up the unit to replace the needed part.

Disposing of the unit

CAUTION

Treat as industrial waste.

General instructions

CAUTION

Many of the drawings and diagrams in this manual show the FC 3500 DC without a cover,

or partially open. Never operate the unit like this. Always replace the cover and follow this

manual when operating the FC 3500 DC.

FC 3500 DC Fan Control Document no.:150304 Version: 1.2

Page 9of 23

3Technical Data

FC 3500 DC Description Comment

Power supply voltage

Power consumption

On/Off switch before

FC 3500 DC

Electronics fuse

J1:

90Vac .. 260Vac, 50/60Hz

34,5 VA

1,5mm2 (14 AWG) flexible or

solid wirring stripped 9mm.

F1: 315 mA / 250Vac Slow

Supply

(L, N, PE)

Water valve output

Internal fuse F2

J20:

Triac output 90Vac .. 260Vac

50/60Hz, Max. 1A

F2: 1 Amp./250Vac Slow

Valve (Lout, N, PE)

Alarm relay output

J5:

SPDT contact, max.

8A/250Vac or 5A/30Vdc

Relay (NO, NC, C)

Dimensions

FC 3500 DC Fan Control

FC 3500 BP Display unit

247 x 145 x 63,5mm

102 x 102 x 44mm

Temperature ranges

Set point

Air Sensor

Water sensor

+9/+29°C (+48/+85°F)

-20/+100°C [-4/+212°F)

Default settings

See parameter list

Temperature

ensors

J9:

Air

sensor /

2,2m

J10: Water-sensor / 2,2m

J11: Outside-sensor / 2,2m

wire 10K NTC)

(2-wire 10K NTC)

Contact input

J19:

Dig_in potential free

contact-input

(

NO, Gnd

)

Optional 3

wire sensor1

Jumper U/I

J12:

Optional sensor1 U or I

J30: Selection U or I input

(+12Vdc, Signal, 0V)

0-1V, 0-10V or 4-20mA

Optional 3

wire sensor2

Jumper U/I

J13:

Optional sensor1 U or I

J31: Selection U or I input

(+12Vdc, Signal, 0V)

0-1V, 0-10V or 4-20mA

Analog output

J14:

U or I output selected by load

Rload>1K = Voltage out,

50E<Rload<400E = Current out

(Signal, Gnd)

Fan outputs

J15:

Fan1 output 3

wire

J16: Fan2 output 3-wire

J17: Fan3 output 3-wire

J18: Fan4 output 3-wire

(FB, Gnd, Signal 0

10V=)

(FB, Gnd, Signal 0-10V=)

On/off control outputs

J2:

Valve, Heat and Fan(s) outputs

Valve output

Heat output

Fan(s) output

(12Vdc out max. 100mA)

Communications

J6:

RS485 with supply for display

J3: Ethernet (to network)

(+12V, A, B, Gnd)

Operation temperature

Storage temperature

Operation humidity

0/+40°C (non

freezing)

-20/+65°C

90%RH or less (non-condensing)

Ambience

Indoors in a ventilated area

(see also operation temp./humidity))

(free from

corrosive gas,

flammable gas, oil, mist,

dust, dirt and water)

FC 3500 DC Fan Control Document no.:150304 Version: 1.2

Page 10 of 23

4Installation

This manual is written for the FC 3500 DC controller unit. Incorrect handling may cause the FC

3500 DC to operate incorrectly, causing its life to be reduced considerably, or at the worst, the FC

3500 DC to be damaged.

Handle the unit properly in accordance with the information in each section as well as the

precautions and instructions of this manual to use it correctly.

4.1 Unpacking the FC 3500 DC unit

Unpack the FC 3500 DC and check the unit for discrepancy, damage etc. If found such please

contact your sales representative.

4.2 Installation of the FC 3500 DC

Avoid places where the unit is exposed to oil mist, flammable gases, fluff, dust, dirt etc. Install the

unit in a clean place or inside a “totally enclosed” panel which does not accept any suspended

matter.

Indice

Altri manuali VDH Unità di controllo

VDH

VDH ALFANET TEMPLOGGER 16x PT1000 Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente