Velleman Velbus VMB4PD Manuale utente

VMB4PD 1

VMB4PD

Push Button and

Timer Module

for Velbus System

VMB4PD 2

Introduction

This unique panel will let you control all of the output modules on the Velbus®system. There is no need to

remember the function of each button, just read the label next to it!

The module also features programmable timing functions to automate daily or weekly button press actions.

The infrared receiver will let you control the module at distance.

Features

Four push buttons and one configuration push button.

Up to 8 commands (2 groups of 4 commands each).

The 2 command groups are directly callable through the configuration push button.

Automatic switchover to the first group of commands after 15 seconds of inactivity.

Push button debounce: 65ms.

Possibility for each push button to react only when maintaining pressed (1s, 2s of 3s).

Adjustable push button backlight: off – low dimming – high dimming – max. intensity.

LED indication for each push button: slow, fast, very fast blinking or continuously on.

Remote Control:

Built-in IR receiver for use with the Velbus®

Can be used with the VMBIRTS IR remote stick

IR modulation: RECS80

Transmitter/receiver range: ±10m

LCD display:

2 lines of 16 characters

White backlight

Adjustable backlight: off – low dimming – high dimming – max. intensity.

Possibility to automatically adjust the backlight intensity (twice a day).

Adjustable contrast through configuration menu.

Labelling on the display for each command, 2 lines of 16 characters for each label

Configuration:

Adjustable display contrast and backlight.

Adjustable push button backlight.

Adjustable command reaction time (at once, 1, 2 or 3 seconds)

Command labelling.

Module address configuration (256 possible addresses).

Clock configuration.

Mode configuration (command panel only, command panel with timer or command panel with timer for the

2nd group of commands).

Input and modification of the timer program steps.

Timer activation or deactivation for a specific push button.

Configuration menu will automatically close after 25 seconds of inactivity.

Clock:

Built-in clock with day display.

Setting one clock will adjust all other clocks on the Velbus® system.

Possibility to configure one clock as main clock – all other clocks will run right.

Timer:

Programmable timer functions for push button command automation.

Up to 20 program steps.

Each program step can automate up to 8 commands.

Push Button and Timer Module for Velbus®System VMB4PD

VMB4PD 3

Power Supply:

Required power voltage: 12 to 18VDC.

Consumption: backlight off: 13mA LEDs off / 15mA LEDs on

backlight lowly dimmed: 14mA LEDs off / 16mA LEDs on

backlight highly dimmed: 18mA LEDs off / 19mA LEDs on

backlight max. intensity: 26mA LEDs off / 27mA LEDs on

Max. consumption (all LEDs activated and backlight max. intensity): 27mA.

Power supply LED indication.

9V-battery connection (clock back-up power).

Back-up battery power consumption: 15mA.

Battery not included.

Dimensions:

Push button module (L x W x H): 66 x 44 x 30 mm

Push button module with frame (L x W x H): 118 x 80 x 30 mm

Frame not included.

VELBUS:

2-wire communication for VELBUS data and 2 wires for power

Data transfer: 16.6kbit/s

Serial data protocol: CAN (Controller Area Network)

Short-circuit proof (towards negative or positive of power)

Bus error indication: 2 x short flash of the indication LED

Self restoring after 25 seconds in case of a bus error

Possibility to assign a name (max. 15 characters) and a reaction time (65ms, 1s, 2s of 3s) which can be

saved in the non-volatile memory.

The command labels are displayed on the LCD. These labels consist of 2 lines of 16 characters each and

will also be saved in the non-volatile memory.

When pressing, maintaining pressed and releasing a push button, an instruction is being sent.

Instructions will be accepted when setting the backlight, switching the indication LEDs on and off, slow,

fast or very fast blinking of the indication LEDs, calling up the module type, the push button names and

when reading from or writing to the non-volatile memory.

The module can respond with the module type, the push button name or the contents from the memory.

VMB4PD 4

Connection

For connection between the modules, use twisted pair cable (ex. EIB 2x2x0.8mm2, UTP 8x0.51mm- CAT5

or other). Use minimum 0.5mm² cable. For long wiring (>50m) or if a lot of modules ( > 10) are connected

to one wire, use 1mm² cable. Connect the 12-18Vdc (mind the polarity) and connect the bus wires (mind the

polarity).

BUS

12V

VMB4PD

-12V+ BUS

TWISTED

PAIR

(0.5mm )

Connect a 9V battery (via the included cable) if you desire to power the clock in case of a power failure.

12V power supply -

Velbus

9V backup

battery

Open

Hint: for advanced level only!

Solder island “J” when using a back-up battery in order to feed the battery.

12V power supply-

Velbus +

Closed

9V backup

battery

Rechargeable

WARNING: NEVER use a regular battery (non rechargeable) when soldering island “J” to avoid

risks of explosion.

VMB4PD 5

Termination:

If the module is connected at the start or end of a cable on the VELBUS, place the ‘TERM’ jumper.

Remove the jumper in all other cases.

If different cable wiring topologies (tree, star, loop, ...) are used, place a jumper on the end module of the

longest cable only, NOT on each end point.

Velbus

transmission LED Velbus®

reception LED

Velbus® power LED

Termination

12V power

supply -

Velbus 9V bac

-up

atter

VMB4PD 6

Use

The module consists of 4 push buttons with corresponding LED indication and one configuration push

button. The label for each push button is displayed on the LCD.

This module allows defining up to 8 commands.

The module will display the first 4 commands by default:

Push the configuration button to switch to the next four commands:

The module switches back to the default command display after 15 seconds of inactivity.

You can switch between the two displays at any time by pressing the configuration button.

When pressing, maintaining pressed and releasing a push button, an instruction is being sent on the

Velbus®. These messages identify which push button has been pressed, maintained pressed or released.

Other modules (relay modules, blind control modules, dimmers...) connected to the Velbus® will react and

answer by resending a command message to the push button module. This command will switch off, light

of blink the indication LEDs.

How a specific push button will control a particular module is explained in the learning mode of the

concerning modules.

Indication LED command 1 Indication LED command 2

Indication LED command 3 Indication LED command 4

Configuration push button

Command 2

Command 4

Command 1

Command 3

Label command 2

Label command 4

Label command 1

Label command 3

Indication LED command 5 Indication LED command 6

Indication LED command 7 Indication LED command 8

Configuration push button

Command 6

Command 8

Command 5

Command 7

Label command 6

Label command 8

Label command 5

Label command 7

VMB4PD 7

Configuration

When using the module in the Velbus®system for the first time, configure:

•contrast

•backlight

•push button backlight

•clock

•address

•labels

•reaction time

•mode

•timer

Call the configuration menu by holding the configuration pressed for 4 seconds.

The configuration menu will be displayed.

Press the upper left push button to activate the clock menu.

Press the upper right push button to activate the display menu.

Press the configuration button to display the next configuration menu.

Press the upper left push button to activate the mode menu.

Press the upper right push button to activate the address menu.

Press the lower left push button to activate the reaction time menu.

Press the lower right push button to activate the label editor.

Press the configuration push button to quit the configuration menu.

Configuration button

Clock menu Display menu

Next configuration menu

Mode menu Address menu

Reaction time

menu Label

editor

Quit configuration menu

VMB4PD 8

Remarks:

•In configuration mode pressing the push buttons will no more be sent through the Velbus®.

•All settings will be saved in the module (even with a power failure).

•The first configuration menu shows menus “Prog” and “Timer on/off” when the timer is activated.

•The module will automatically quit the configuration mode after 30 seconds of inactivity.

•Hold the configuration button pressed for 8 seconds to display the configuration menu which allows

modifying contrast and backlight.

VMB4PD 9

Setting the Display Contrast

1. Hold the configuration button pressed for 4 seconds to display the configuration menu.

2. Press the upper right button to display the display menu.

3. Adjust the display contrast using the two upper buttons.

4. Press the configuration button repeatedly to quit the display menu.

Remarks:

•Hold the configuration button pressed for 8 seconds to display the contrast mode.

•The display contrast may be set too low if experiencing a blank display. Hold the configuration button

pressed for 8 seconds to switch the module to the configuration menu which allows modifying contrast.

Hold the upper right push button pressed for 3 seconds. The contrast will be set at its maximum.

•The module will automatically quit the configuration mode after 30 seconds of inactivity.

Configuration button

Display menu

Less contrast More contrast

Next display menu

VMB4PD 10

Setting the Display and Push Button Backlight

The backlight intensity can be set according to your preferences (completely off, completely on or

dimmed). The module allows you to automatically modify the intensity twice a day.

The push button backlight intensity can also be set according to your preferences. This is useful when

trying to locate the buttons in a completely dark room.

1. Hold the configuration button pressed for 4 seconds to display the configuration menu.

2. Press the upper right button to display the display menu.

3. Press the lower buttons to adjust the backlight intensity.

4. Press the configuration button to display the next display button.

5. Press the upper right button to (de)activate the backlight.

Configuration button

Display menu

Display backlight Push button backlight

Next display menu

Indice

Altri manuali Velleman Unità di controllo

Velleman

Velleman VMA406 Manuale utente

Velleman

Velleman WPM400 Manuale utente

Velleman

Velleman VMA338 Manuale utente

Velleman

Velleman VMA405 Manuale utente

Velleman

Velleman Whadda WPM463 Manuale utente

Velleman

Velleman VMA453 Manuale utente

Velleman

Velleman VM131 Manuale utente

Velleman

Velleman ARDUINO VMA307 Manuale utente

Velleman

Velleman VMA450 Manuale utente

Velleman

Velleman K8006 Manuale utente

Velleman

Velleman VMA207 Manuale utente

Velleman

Velleman VMA325 Manuale utente

Velleman

Velleman VMA422 Manuale utente

Velleman

Velleman VMA404 Manuale utente

Velleman

Velleman K4400 Manuale utente

Velleman

Velleman VMA432 Manuale utente

Velleman

Velleman VMM005 Manuale utente

Velleman

Velleman Whadda WPSE358 Manuale utente

Velleman

Velleman Whadda WPM300 Manuale utente

Velleman

Velleman DVM97CM Manuale utente

Velleman

Velleman Whadda WPM357 Manuale utente

Velleman

Velleman MM111 Manuale utente

Velleman

Velleman VMA318 Manuale utente

Velleman

Velleman K2636 Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente