VIA Technologies CM30-SC Manuale utente

CM30-SC

CM35-SC

Rev. A+

44400034

System Board Users Manual

Carte Mère Manuel Pour Utilisateur

System-Platine Benutzerhandbuch

Tablero Electrónico del Sistema Manual del

Usuario

This publication contains information that is protected by copyright. No part of it may

be reproduced in any form or by any means or used to make any transformation/

adaptation without the prior written permission from the copyright holders. This

publication is provided for informational purposes only. The manufacturer makes no

representations or warranties with respect to the contents or use of this manual and

specifically disclaims any express or implied warranties of merchantability or fitness for

any particular purpose. The user will assume the entire risk of the use or the results of

the use of this document.

The manufacturer reserves the right to revise this publication and make

changes to its contents at any time, without obligation to notify any person or

entity of such revisions or changes.

Le fabricant se réserve le droit de revoir cette publication et deffecteur des

changements dans son contenu sans obligation dun préavis quelconque à qui

que ce soit.

Der Hersteller behält sich das Recht vor, den Inhalt dieses Handbuchs jederzeit

und ohne Benachrichtigung zu überarbeiten und abzuändern.

El fabricante reserva el derecho de corregir esta publicación y hacer cambios a

sus contenidos en cualquier tiempo, sin obligación de notificar a cualquier

persona o entidad de tales revisiones o cambios.

Trademarks

Microsoft®MS-DOS®, WindowsTM, Windows®95, Windows®98, Windows®98 SE,

Windows®2000 and Windows NT®4.0 are registered trademarks of Microsoft

Corporation. Intel®, Pentium®III and CeleronTM are registered trademarks of Intel

Corporation. VIA CyrixIII is a registered trademark of VIA Technologies, Inc. Award is a

registered trademark of Award Software, Inc. Other trademarks and registered trademarks

of products appearing in this manual are the properties of their respective holders.

Caution:

Danger of explosion if battery incorrectly replaced.

Replace only with the same or equivalent type recommended by the manufacturer.

Dispose of used batteries according to the battery manufacturers instructions.

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC rules. These limits are designed to

provide reasonable protection against harmful interference when the equipment is

operated in a residential installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment

does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and the receiver.

 Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

 Consult the dealer or an experienced radio TV technician for help.

Notice:

1. The changes or modifications not expressly approved by the par ty responsible for

compliance could void the user's authority to operate the equipment.

2. Shielded interface cables must be used in order to comply with the emission

limits.

English

Français

Deutsch

Español

Table of Contents / Table des Matières / Inhaltsverzeichnis / Tabla de Contenidos

Read Me First...........................................................................................................................................

Chapter 1 - Introduction

1.1 Features and Specifications............................................................................................

1.2 Package Checklist................................................................................................................

Chapter 2 - Hardware Installation

2.1 System Board Layout ......................................................................................................

2.2 Frequency Ratio Settings for Processors...............................................................

2.3 Jumper Settings for Selecting the CPUs Front Side Bus...............................

2.4 Jumper Settings for the Onboard Audio Codec...............................................

2.5 Jumper Settings for Clearing CMOS Data............................................................

2.6 Connectors..............................................................................................................................

Chapter 3 - Award BIOS Setup Utility

3.1 Entering the Award BIOS Setup Utility....................................................................

3.2 Setting the Date and Time..............................................................................................

3.3 Selecting the Hard Drive and Floppy Drive Type............................................

3.4 Selecting the Boot Sequence of the Drives..........................................................

3.5 Enabling the Processor Serial Number Function...............................................

3.6 Selecting the Power Lost Resume State..................................................................

3.7 Using the Suspend to RAM Function.......................................................................

3.8 Loading Fail-Safe Defaults/Optimized Defaults...................................................

3.9 Setting the Supervisor/User Password...................................................................

Chapter 4 - Supported Softwares

4.1 VIA Hardware Monitor...................................................................................................

4.2 VIA Service Pack................................................................................................................

4.3 Audio Drivers and Software Application..............................................................

4.4 Drivers and Utilities Installation Notes....................................................................

Note:

The users manual in the provided CD contains detailed information about the

system board. If, in some cases, some information doesnt match those shown in this

manual, this manual should always be regarded as the most updated version. To

view the users manual, insert the CD into a CD-ROM drive. The autorun screen

(Main Board Utility CD) will appear. Click Users Manual.

Introduction

Read Me First

This page contains a summary of the important notes that must be given special

attention to prior to using the system board.

1. Processor

 The frequency ratio of some processors may have been locked by the

manufacturer. If you are using this kind of processor, setting an extended

ratio for the processor will have no effect. The system will instead use its

factory default ratio.

 The frequency ratio of processors greater than 8x has been locked by

the manufacturer and will no longer have the flexibility of using extended

ratios. Therefore, the system will use the processors factory default ratio.

 Selecting an external bus clock other than 66MHz, 100MHz or 133MHz

may result to the processors or systems instability and are not

guaranteed to provide better system performance.

2. System Memory -The system board supports both VCM and PC SDRAM

DIMMs. If you are using more than one DIMM, make sure you insert the

same type of DIMMs into the DIMM sockets. Using different types (VCM or

PC SDRAM) of DIMMs may cause problems.

3. 5VSB Power - If you are using the (1) Wake-On-LAN and/or (2) Wake-On-

Ring (internal modem) functions, the 5VSB power source of your power

supply must support ≥720mA. If you are using the Suspend to RAM function,

the 5VSB power source of your power supply must support ≥1A.

4. Drivers - Make sure to reboot the system after each driver installation.

Problems will occur if you reboot only after installing all the drivers.

Lisez Moi dAbord

Cette page contient un condensé des notes importantes quil faut prendre en

considération avant dutiliser la carte système.

1. Processeur

 La taux de la fréquence de quelques processeurs au-dessus peut avoir

été blocké par le fabricant. Si vous utilisez ce genre de processeur, mettre

une taux étendue pour le processeur aura non effet. Le système utilisera

la taux défaut de lusine plutôt.

 La taux de la fréquence de processeurs plus grand que 8x ont été

blocké par le fabricant et naura plus la flexibilité dutiliser de taux

étendus. Le système utilisera la taux défaut de lusine plutôt.

 Le fait de sélectionner une horloge de bus externe autre que 66MHz,

100MHz ou 133MHz peut rendre le processeur ou le système instable et

ne garantit pas doffrir de meilleures performances système.

2. Mémoire Système - La carte système supporte à la fois les VCM et DIMM

PC SDRAM. Si vous utilisez plus dune DIMM, prenez soin dinsérer le même

type de DIMM dans les logements DIMM. Le fait dutiliser des DIMM de

type différents (VCM ou PC SDRAM) peut engendrer des problèmes.

3. Alimentation 5VSB - Si vous utilisez les fonctions (1) Eveil LAN (Wake-On-

LAN) et/ou (2) Eveil Sonnerie (Wake-On-Ring) (modem interne), la source

dalimentation 5VSB de votre bloc dalimentation doit supporter ≥720mA. Si

vous utilisez les fonctions Suspension sur RAM, la source dalimentation 5VSB

de votre bloc dalimentation doit supporter ≥1A.

4. Pilotes - Prenez soin de réamorcer le système après linstallation de chaque

pilote. Des problèmes apparaîtront si vous réamorcez seulement après

linstallation de tous les pilotes.

English

Français

Introduction

Lesen Sie Diese Anleitung Zuerst Durch

Auf dieser Seite ist eine Zusammenfassung aller Hinweise enthalten, die vor der

Benutzung der Systemplatine unbedingt beachtet werden müssen.

1. Prozessor

 Die Frequenzrate von einige, Prozessoren konnte vielleicht von Hersteller

gesperrt sein. Wenn Sie diese Art von Prozessor benutzen, wird das

eingeben eine erweiterte Rate für den Prozessor keine Wirkung haben.

Das System wird stattdessen den Standard Fabrikrate benutzen.

 Die Frequenzrate von Prozessoren, welche größer als 8x sind, sind von

Hersteller gesperrt, und werden nicht länger die erweiterten Raten

Flexibilität haben. Das System wird stattdessen den Standard Fabrikrate

benutzen.

 Ein Auswählen eines Bus-Taktgebers, welcher von den Frequenzen 66MHz,

100MHz oder 133MHz abweicht, kann eine Unstabilität des Prozessors

oder des Systems verursachen. Eine bessere Betriebsleistung des Systems

kann durch eine solche Einstellung nicht gewährleistet werden.

2. Systemspeicher - Die Systemplatine unterstützt die VCM- sowie die PC-

SDRAM-DIMMs. Falls mehr als ein DIMM verwendet wird, darf nur derselbe

Typ der DIMMs in die DIMM-Steckfassungen eingesetzt werden, da andere

DIMM-Typen (VCM oder PC SDRAM) zu Konflikten führen können.

3. 5VSB-Stromversorgung - Falls Sie die (1) Wake-On-LAN- und/oder (2)

Wake-On-Ring-Funktionen (internes Modem) anwenden, unterstützt die 5VSB-

Stromquelle Ihres Netzgerätes eine Leistung von ≥720 mA. Falls Sie die

Suspendieren-auf-RAM-Funktion, unterstützt die 5VSB-Stromquelle Ihres

Netzgerätes eine Leistung von ≥1A.

4. Treiber - Das System muß nach jedem Installieren eines Treibers neugestartet

werden. Probleme werden nur dann auftreten, wenn das System nach dem

Installieren aller Treiber neugestartet wird.

Leer Me Primero

Esta pagina contiene informationes importantes que se deben prestar mucha

attention antes del uso de la tabla de sistema

1. Procesador

 La proporción de frecuencia de algunos procesadores de arriba uede

que ha sido bloqueada por el fabricante. Si usted está utilizando esta

clase de procesador, configurando la ración para el procesador no

tendrá efecto. El sistema en vez utilizará la proporción implícita de la

fábrica.

 La ración de frecuencia de los procesadores mayor que 8x ha sido

bloquada por el fabricante y ya no tendrá la flexibilidad de utilizar las

proporciones extendidas. El sistema utiliza su proporción implícita de la

fábrica.

 Seleccionando un reloj de bus externo otro que 66MHz, 100MHz o

133MHz puede resultar la inestabilidad del procesador o del sistema y

no son garantizados para proveer una mejor ejecución de sistema.

2. Memoria de Sistema - El tabla del sistema suporta ambos, el VCM y el PC

SDRAM DIMMs. Si usted está utilizando más que un DIMM, asegura de

insertar el mismo tipo de DIMM dentro del encaje de DIMM. Utilizando

diferentes tipos (VCM o PC SDRAM) de DIMM puede causar problemas.

3. 5VSB Potencia - Si estas usando las funciones de (1) Wake-On-LAN  y/o

si se esta usando el (2) Wake-On-Ring (que es el modem interno), el 5VSB

potencia debe soportar una corrient (>) mas grande que ≥720mA. Si estas

usando las funciones de Suspender a RAM, el 5VSB potencia debe soportar

una corrient (>) mas grande que ≥1A.

4. Drivers - Asegurese de reboot o rebootear el sistema cada vez que se

instala un nuevo Driver. Problemas suelen ocurrir si se rebootea solo una

vez despuez de haber terminado con las instalacionens de todos los drivers.

Deutsch

Español

Introduction

Expansion Slots

The CM35-SC system board is equipped with 1 shared AGP / DFP (Digital Flat

Panel) slot while CM30-SC is only equipped with the DFP slot.

The AGP slot on the CM35-SC system board is a universal AGP slot. AGP is an

interface designed to support high performance 3D graphics cards. It utilizes a

1.1 Features and Specifications

Caractéristiques et Spécifications

Leistungsmerkmale und Technische Daten

Características y Especificaciones

1.1.1 Features

Chipset

 VIA®8604/82C686A AGPset (PL133) - CM30-SC

 VIA®8605/82C686A AGPset (PM133) - CM35-SC

Processor

The system board is equipped with a switching voltage regulator that

automatically detects 1.30V to 3.5V.

 Pentium®III FCPGA 133MHz FSB (533EB-933EB) or 100MHz FSB (500E-

850E) processor

 CeleronTM 66MHz FSB: FCPGA (566MHz-700MHz) or PPGA (300A-

533MHz) processor

 VIA CyrixIII processor

System Memory

 Up to 1GB using VCM (Virtual Channel Memory) or PC SDRAM DIMM

(unbuffered or registered)

 Two 168-pin DIMM sockets

 Uses x64 PC SDRAM, 3.3V

: PC-66 SDRAM DIMM for 66MHz FSB processors

: PC-100 SDRAM DIMM for 100/66MHz FSB processors

: PC-133 SDRAM DIMM for 133MHz FSB processors

Chapter 1 - Introduction

Introduction

Einleitung

Introducción

English

Note:

If you are using more than one DIMM, make sure you insert the same type

of DIMMs into the DIMM sockets. Using different types (VCM or PC

SDRAM) of DIMMs may cause problems.

DIMMs

2MBx64

4MBx64

8MBx64

Memory Size

16MB

32MB

64MB

DIMMs

16MBx64

32MBx64

64MBx64

Memory Size

128MB

256MB

512MB

Introduction

dedicated pipeline to access system memory for texturing, z-buffering and alpha

blending. The universal AGP slot supports AGP 2x with up to 533MB/sec.

bandwidth and AGP 4x with up to 1066MB/sec. bandwidth for 3D graphics

applications. AGP in this system board will deliver faster and better graphics to

your PC.

Both system boards are also equipped with 2 dedicated PCI slots and 1 shared

AMR/ISA slot. AMR (Audio/Modem Riser) is an interface designed for installing

an audio riser card, modem riser card or audio/modem riser card that is

compliant to the AMR specification.

Onboard Graphics Features

 Integrated Savage4 2D/3D/Video accelerator

- Shares 1MB of the system memory

- Optimized Shared Memory Architecture (SMA)

- Full AGP 4x, including sideband addressing and execute mode

- High quality DVD video playback

 3D rendering features

- 32-bit true color rendering

- MPEG-2 video textures

 2D hardware acceleration features

 Motion video architecture

 Software drivers

- Windows®95/98/2000

- Windows NT®4.0

Onboard Audio Features

 Supports Microsoft®DirectSound/DirectSound 3D

 AC97 supported with full duplex, independent sample rate converter for

audio recording and playback

ATX Double Deck Ports (PC 99 color-coded connectors)

 2 USB ports

 1 NS16C550A-compatible DB-9 serial port

 1 DB-15 VGA por t

 1 SPP/ECP/EPP DB-25 parallel port

 1 mini-DIN-6 PS/2 mouse port

 1 mini-DIN-6 PS/2 keyboard port

 1 game/MIDI port

 3 audio jacks: line-out, line-in and mic-in

Connectors

 1 connector for 2 additional external USB ports

 1 9-pin connector for 1 external serial port

 1 connector for IrDA interface

 2 IDE connectors

 1 floppy drive interface supports up to two 2.88MB floppy drives

 1 20-pin ATX power supply connector

 1 Wake-On-LAN connector

 1 Wake-On-Ring connector

 CPU and chassis fan connectors

 3 internal audio connectors (AUX-in, CD-in and TAD)

PCI Bus Master IDE Controller

 Two PCI IDE interfaces support up to four IDE devices

 Supports ATA/33 or ATA/66 hard drives

Introduction

 PIO Mode 3 and Mode 4 Enhanced IDE (data transfer rate up to 16.6MB/

sec.)

 Bus mastering reduces CPU utilization during disk transfer

 Supports ATAPI CD-ROM, LS-120 and ZIP

IrDA Interface

The system board is equipped with an IrDA connector for wireless connectivity

between your computer and peripheral devices. It supports peripheral devices

that meet the HPSIR or ASKIR standard.

USB Ports

The system board supports 4 USB ports. Two onboard USB ports are located

at the ATX double deck ports of the board. The J23 connector on the system

board allows you to connect the optional 3rd and 4th USB ports. These

optional USB ports, which are mounted on a card-edge bracket, will be

provided as an option. USB allows data exchange between your computer and

a wide range of simultaneously accessible external Plug and Play peripherals.

BIOS

 Award BIOS, Windows®95/98/2000 Plug and Play compatible

 Supports SCSI sequential boot-up

 Flash EPROM for easy BIOS upgrades

 Supports DMI 2.0 function

 2Mbit flash memory

Desktop Management Interface (DMI)

The system board comes with a DMI 2.0 built into the BIOS. The DMI utility in

the BIOS automatically records various information about your system

configuration and stores these information in the DMI pool, which is a part of

the system board's Plug and Play BIOS. DMI, along with the appropriately

networked software, is designed to make inventory, maintenance and

troubleshooting of computer systems easier.

1.1.2 System Health Monitor Functions

The system board is capable of monitoring the following system health

conditions.

 Monitors CPU/system temperature and overheat alarm

 Monitors VCORE/3.3V/5V/12V/2.5V voltages and failure alarm

 Monitors CPU/chassis fan speed and failure alarm

 Automatic CPU and chassis fans on/off control

 Read back capability that displays temperature, voltage and fan speed

If you want a warning message to pop-up or a warning alarm to sound when an

abnormal condition occurs, you must install the VIA Hardware Monitor utility.

This utility is included in the CD that came with the system board. Refer to the

VIA Hardware Monitor section in chapter 4 for more information.

1.1.3 Intelligence

Automatic CPU/Chassis Fan Off

The CPU and chassis fans will automatically turn off once the system enters the

Suspend mode.

Dual Function Power Button

Depending on the setting in the Soft-Off By PWRBTN field of the Power

Management Setup, this switch will allow the system to enter the Soft-Off or

Suspend mode.

Introduction

Wake-On-Ring

This feature allows the system that is in the Suspend mode or Soft Power Off

mode to wake-up/power-on to respond to calls coming through an internal or

external modem.

Important:

If you are using a modem add-in card, the 5VSB power source of your

power supply must support a minimum of

≥

720mA.

RTC Timer to Power-on the System

The RTC installed on the system board allows your system to automatically

power-on on the set date and time.

Wake-On-LAN

The Wake-On-LAN function allows the network to remotely wake up a Soft

Power Down (Soft-Off) PC. Your LAN card must support the remote wakeup

function.

Important:

The 5VSB power source of your power supply must support

≥

720mA

(minimum).

AC Power Failure Recovery

When power returns after an AC power failure, you may choose to either

power-on the system manually, let the system power-on automatically or return

to the state where you left off before power failure occurs. Refer to Selecting

the Power Lost Resume State in chapter 3 for more information.

ACPI STR

The system board is designed to meet the ACPI (Advanced Configuration and

Power Interface) specification. ACPI has energy saving features that enables PCs

to implement Power Management and Plug-and-Play with operating systems that

support OS Direct Power Management. Currently, only Windows®98/2000

supports the ACPI function. ACPI when enabled in the Power Management Setup

will allow you to use the Suspend to RAM function.

With the Suspend to RAM function enabled, you can power-off the system at

once by pressing the power button or selecting Standby when you shut down

Windows®98/2000 without having to go through the sometimes tiresome

process of closing files, applications and operating system. This is because the

system is capable of storing all programs and data files during the entire

operating session into RAM (Random Access Memory) when it powers-off. The

operating session will resume exactly where you left off the next time you

power-on the system. Refer to Using the Suspend to RAM Function in chapter

3 for more information.

Important:

The 5VSB power source of your power supply must support

≥

1A.

Virus Protection

Most viruses today destroy data stored in hard drives. The system board is

designed to protect the boot sector and partition table of your hard disk drive.

Introduction

Note:

Si vous utilisez plus dune DIMM, prenez soin dinsérer le même type de

DIMM dans les logements DIMM. Le fait dutiliser des DIMM de type

différents (VCM ou PC SDRAM) peut engendrer des problèmes.

Mémoire

16MB

32MB

64MB

Mémoire

128MB

256MB

512MB

Logements dExtension

La carte système CM35-SC est équipée dun créneau partagé AGP / DFP

(Digital Flat Panel) alors que la carte CM30-SC est seulement équipée dun

créneau DFP. Le créneau AGP sur la carte système CM35-SC est un créneau

AGP universel. AGP est une interface conçue pour supporter des cartes

graphiques 3D de haute performance. Elle utilise un pipeline dédié pour accéder

à la mémoire système pour le texturage, le z-buffering et le mélange alpha. Le

slot AGP universel supporte 2x AGP avec une bande passante allant jusquà

533Mo/sec et 4x AGP avec une bande passante allant jusquà 1066Mo/sec pour

les applications graphiques 3D. AGP sur cette carte système offrira des

graphiques meilleurs et plus rapide à votre PC.

Les deux cartes systèmes sont aussi équipées de deux créneaux PCI dédiés et

dun créneau AMR/ISA partagé. AMR (Riser Audio/Modem) est dune interface

destinée à linstallation dune carte audio riser, carte modem riser ou dune carte

audio/modem réhausseur conforme aux spécifications AMR.

1.1.1 Caractéristiques

Chipset

 VIA®8604/82C686A AGPset (PL133) - CM30-SC

 VIA®8605/82C686A AGPset (PM133) - CM35-SC

Processeur

La carte système est équipée dun régulateur de commutation de voltage qui

détecte automatiquement de 1.30V à 3.5V.

 Pentium®III FCPGA 133MHz FSB (533EB-933EB) ou 100MHz FSB (500E-

850E) processeur

 CeleronTM 66MHz FSB: FCPGA (566MHz-700MHz) ou PPGA (300A-

533MHz) processeur

 VIA CyrixIII processeur

Mémoire Système

 Supporte jusquà 1Go de mémoire utilisant VCM (Virtual Channel Memory)

ou PC SDRAM DIMM (tampon ou enregistrées)

 2 sockets DIMM 168 broches.

 Utilise x64 PC SDRAM, 3.3V

- PC-66 SDRAM DIMM pour processeurs 66MHz FSB

- PC-100 SDRAM DIMM pour processeurs 100/66MHz FSB

- PC-133 SDRAM DIMM pour processeurs 133MHz FSB

Français

DIMMs

2MBx64

4MBx64

8MBx64

DIMMs

16MBx64

32MBx64

64MBx64

Questo manuale è adatto per i seguenti modelli

Altri manuali VIA Technologies Scheda madre

VIA Technologies

VIA Technologies KT880 Manuale utente

VIA Technologies

VIA Technologies EPIA-5000 - VIA Motherboard - Mini ITX Manuale utente

VIA Technologies

VIA Technologies Mini-ITX Mainboard EPIA-MII Manuale utente

VIA Technologies

VIA Technologies VAB-1000 Manuale utente

VIA Technologies

VIA Technologies VT82C691 Manuale per l'uso e la cura

VIA Technologies

VIA Technologies EPIA-EK10000G - VIA Motherboard - Mini ITX Manuale utente

VIA Technologies

VIA Technologies EPIA-ML Manuale utente

VIA Technologies

VIA Technologies EPIA-P830 Manuale utente

VIA Technologies

VIA Technologies EPIA-M850 Manuale utente

VIA Technologies

VIA Technologies VB8001 Manuale utente

VIA Technologies

VIA Technologies EPIA-P720 Manuale utente

VIA Technologies

VIA Technologies P4M890DMP VT8237R Plus Manuale utente

VIA Technologies

VIA Technologies EPIA-M920 Manuale utente

VIA Technologies

VIA Technologies EPIA-LT Manuale utente

VIA Technologies

VIA Technologies EPIA-E900 Manuale utente

VIA Technologies

VIA Technologies EPIA NL-Series Manuale utente

VIA Technologies

VIA Technologies VAB-950 Manuale utente

VIA Technologies

VIA Technologies VAB-630 Manuale utente

VIA Technologies

VIA Technologies EPIA N-Series Manuale utente

VIA Technologies

VIA Technologies KM400 Manuale di istruzioni

VIA Technologies

VIA Technologies EPIA-E900-12Q Manuale utente

VIA Technologies

VIA Technologies P4M800 Manuale di istruzioni

VIA Technologies

VIA Technologies EPIA-EX15000G - VIA Motherboard - Mini ITX Manuale utente

VIA Technologies

VIA Technologies EPIA-CN13000G - VIA Motherboard - Mini ITX Manuale utente

Manuali Scheda madre popolari di altre marche

DFI

DFI SD170 Manuale utente

ASROCK

ASROCK ROMED8-2T Manuale utente

Asus

Asus P2L97A Manuale utente

Winmate

Winmate IC70 Manuale utente

Asus

Asus MES-B Manuale utente

Grantech

Grantech SYS8F377VGGA-3OMN Manuale utente

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuale utente

Gigabyte

Gigabyte GA-9IVDT Manuale utente

Texas Instruments

Texas Instruments ADS8372EVM Manuale utente

Commell

Commell MS-C73 Manuale utente

IBT Technologies

IBT Technologies MB860 Manuale utente

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuale utente

Biostar

Biostar M7VIT Bravo Istruzioni per l'uso e l'installazione

Intel

Intel D33217CK Manuale utente

Asus

Asus F1A55-M LX PLUS R2.0 Manuale utente

EPC

EPC EPC9147C Manuale utente

Asus

Asus EX-B760M-V5 D4 Manuale utente

EPOX

EPOX MU-8KHA0010 Manuale utente