Viessmann VITOSOLIC 100 Istruzioni operative
Operating instructions
for the system user
VIESMANN
Control unit for solar thermal systems
VITOSOLIC 100
5592 640 GB 4/2014 Please keep safe.
2
Please follow these safety instructions closely to prevent accidents and mate-
rial losses.
Safety instructions explained
Danger
This symbol warns against the
risk of injury.
!Please note
This symbol warns against the
risk of material losses and envi-
ronmental pollution.
Note
Details identified by the word "Note" con-
tain additional information.
Target group
These operating instructions are inten-
ded for system users.
This appliance can also be operated by
children of 8 years and older, as well as
by individuals with reduced physical,
sensory or mental faculties or those lack-
ing in experience and knowledge, provi-
ded such individuals are being super-
vised or have been instructed in the safe
use of this appliance as well as in any
risks arising from it.
!Please note
Supervise children in the proxim-
ity of the appliance.
■ Never permit children to play
with the appliance.
■ Cleaning and maintenance
must not be carried out by
unsupervised children.
Appliance connection
■ The appliance may only be connected
and commissioned by authorised con-
tractors.
■ Observe the specified electrical con-
nection requirements.
■ Modifications to the existing installa-
tion may only be carried out by author-
ised contractors.
Danger
Incorrectly executed work on the
system can lead to life-threaten-
ing accidents.
Work on electrical equipment
must only be carried out by a
qualified electrician.
Work on the appliance
■ All settings and work on the appliance
must be carried out as specified in
these operating instructions.
Further work on the appliance may
only be carried out by authorised con-
tractors.
■ Never open the appliance.
■ Never change or remove fitted acces-
sories.
In case of fire
Danger
Fire presents a risk of burns and
explosion.
■ Switch the system OFF.
■ Use a tested fire extinguisher,
class ABC.
Safety instructions
For your safety
5592 640 GB
3
Auxiliary components, spare and
wearing parts
!Please note
Components that were not tested
with the system may cause sys-
tem damage, or may affect its
functions.
Have all installation or replace-
ment work carried out by qualified
contractors.
Safety instructions
For your safety (cont.)
5592 640 GB
4
The commissioning and adjusting of the
control unit to local conditions and to
building characteristics, plus the instruc-
tion of the user in operating the system,
must be carried out by your heating con-
tractor.
Introductory information
Commissioning
5592 640 GB
5
Controls
KOL
°C
AB
AOK to confirm your selection or
setting.
BSymbols line
To terminate a value adjustment
in progress.
/ Cursor keys
To scroll through the menu.
/ Cursor keys
To adjust values.
To change from the scanning level
to the setting level
To the right, underneath the symbol line
on the display, you will see which keys
you can operate to make adjustments
and scans.
Symbols on the display
These symbols are not always dis-
played, but appear subject to the system
operating condition.
Operation
Operation
5592 640 GB
6
Symbol Permanent display Flashing
The system is operational. —
ÂRelay 1 is on.
The solar circuit pump is run-
ning.
—
ÃRelay 2 is on. —
ÈThe set DHW temperature
has been reached.
Collector cooling function, re-
turn cooling function enabled
ÇThe frost protection function
is enabled.
Failed to reach minimum col-
lector temperature
¨— Emergency collector shut-
down (collector limit tempera-
ture reached) or cylinder
emergency stop active
¨+ÄSensor fault:
Ä ¨
¨+ÆManual mode:
Æ ¨
SET You can change the relevant
parameters.
Change parameters with
/ .
Operation
Operation (cont.)
5592 640 GB
7
Use / to scan the following actual val-
ues subject to the system equipment
level:
■
Note
The flashing sensor symbol in the sys-
tem scheme shows the position of the
actual temperature.
KOL – Collector temperature in °C
(standard display)
■TSPU – DHW temperature in °C
■S3 – Thermostat temperature in °C,
temperature at any additional connec-
ted sensor that may be connected
■n1% – Solar circuit pump speed
■n2% – Operating condition of the
actuator at relay output R2
■hP1 – Hours run of the equipment at
relay output 1
■hP2 – Hours run of the equipment at
relay output 2
■KWh – Amount of heat in kWh, if the
heat meter is enabled
■MWh – Amount of heat in MWh, if the
heat meter is enabled
Note
Add the values for MWh and kWh
together.
Resetting hours run and amount of
heat
Whilst the value is displayed, press the
following keys:
1. OK "SET" flashes. Value 0
appears.
2. OK to confirm
Scanning options
Displaying actual values
5592 640 GB
8
Cause Remedy
The solar control unit MCB has respon-
ded.
Inform your local heating contractor.
Power failure The solar control unit automatically re-
turns to operation once the power supply
has been restored.
The power distribution MCB (main do-
mestic MCB) has responded.
Check the MCB and inform your heating
contractor if necessary.
The collector limit temperature or maxi-
mum cylinder temperature has been
reached.
Wait until the relevant temperature has
fallen below its respective limit.
The solar control unit is in manual mode.
The display shows "Æ" and "¨" flash-
es.
Select "Auto":
1. Press until "ANL" is displayed.
2. Press until "HND 1" or "HND 2" is
displayed.
3. Press OK, "SET" flashes.
4. Press until "Auto" is displayed.
5. Press OK to confirm.
6. Press . The collector temperature is
displayed.
There is no DHW available
Cause Remedy
The solar control unit is faulty. Inform your local heating contractor.
The collector temperature is too high,
safety shutdown by the solar control
unit.
Wait until the collector temperature has
dropped.
The set cylinder temperature (set DHW
temperature) is set too low.
Inform your local heating contractor.
The solar circuit pump is faulty. Inform your local heating contractor.
The DHW cylinder is not being reheated:
The operating and time programs on the
boiler control unit are incorrectly set.
Enable DHW heating.
Operating instructions of the boiler
control unit
What to do if...
The solar thermal system does not start
5592 640 GB
9
Cause Remedy
Example, sensor fault
KOL
°C
The sensor symbol in the system scheme
flashes quickly.
¨ flashes.
Read off the fault code. Inform your local
heating contractor.
In the example, the collector temperature
sensor has a short circuit.
–88.8 Sensor short circuit
888.8 Sensor lead break
Note
Check other sensors with / .
What to do if...
The display is flashing
5592 640 GB
10
DHW cylinder (if installed)
Standards DIN 1988-8 and EN 806 spec-
ify that maintenance and cleaning should
be carried out no later than 2 years after
commissioning and as required there-
after.
Only a qualified heating contractor
should clean the inside of a DHW cylin-
der and the DHW connections.
If any water treatment equipment (e.g. a
sluice or injection system) is installed in
the cold water supply of the DHW cylin-
der, ensure this is refilled in good time.
In this connection, observe the manufac-
turer's instructions.
In addition for Vitocell 100:
We recommend that the correct function
of the sacrificial anode is checked annu-
ally by your heating contractor.
The function of the sacrificial anode can
be checked without interrupting the sys-
tem operation. The heating contractor
will check the earth current with an
anode tester.
Safety valve (DHW cylinder)
The function of the safety valve must be
checked every six months by the user or
a contractor through venting (see valve
manufacturer's instructions). The valve
seat may become contaminated.
Water may drip from the safety valve
during a heat-up process. The outlet is
open to the atmosphere and must not be
closed off.
Potable water filter (if installed)
To maintain high hygienic standards,
proceed as follows:
■ Replace filter element on non-back
flushing filters every six months (visual
inspection every two months).
■ On back flushing filters, back flush
every two months.
Upkeep
Inspection and maintenance
5592 640 GB
Altri manuali per VITOSOLIC 100
7
Indice
Altri manuali Viessmann Unità di controllo
Viessmann
Viessmann VITOTRONIC 100 Istruzioni operative
Viessmann
Viessmann VITOTRONIC 300 Guida rapida
Viessmann
Viessmann VITOCAL 150-A Istruzioni operative
Viessmann
Viessmann 5557 Manuale utente
Viessmann
Viessmann EM-EA1 extension Istruzioni operative
Viessmann
Viessmann 5066 Manuale utente
Viessmann
Viessmann Vitocom 100 LAN1 Guida rapida
Viessmann
Viessmann BCU Manuale utente
Viessmann
Viessmann VITOTRONIC SPS Istruzioni operative
Viessmann
Viessmann 5205 Manuale utente
Viessmann
Viessmann VITOTRONIC 200 Guida rapida
Viessmann
Viessmann Vitotronic 100 HC1 Manuale
Viessmann
Viessmann SDIO/SM1A Guida rapida
Viessmann
Viessmann EM-EA1 extension Guida rapida
Viessmann
Viessmann VITOTRONIC 300 Guida rapida
Viessmann
Viessmann 5222 Manuale utente
Viessmann
Viessmann Vitovolt 300 Guida rapida
Viessmann
Viessmann VITOTRONIC 200 Manuale utente
Viessmann
Viessmann VITOTRONIC 100 Istruzioni operative
Viessmann
Viessmann Vitocom 100 LAN1 Manuale tecnico
Manuali Unità di controllo popolari di altre marche
Festo
Festo Compact Performance CP-FB6-E Manuale elenco delle parti
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuale utente
JS Automation
JS Automation MPC3034A Manuale utente
JAUDT
JAUDT SW GII 6406 Series Guida rapida
Spektrum
Spektrum Air Module System Manuale utente
BOC Edwards
BOC Edwards Q Series Manuale utente
