Vitek Transcendent Series Manuale utente
VITEK
VITEK
PLEASE NOTE:
Complete User Guide, Software, Tools, and Updates are
available online. Scan the QR Code or visit:
http://www.vitekcctv.com/Downloads
VTD-TND6FP
Transcendent Series 6
Megapixel H.265 IP Vandal 360°
Fisheye Camera w/6 IR LEDs
QUICK START GUIDE
FEATURES
• 1/2.9” 6.0 MegaPixel CMOS Image Sensor
• Up to 30fps live view @ 6 MegaPixel
• Multiple Views: 360° Overview, Double 180° Panorama View, Overview
+ 3 Views, and Single View
• 1.07mm @ F2.5 Fisheye Lens with 180° horizontal field of view (wall
mounted) / 360° (ceiling mounted)
• 6 High Power Covert IR LEDs with 50’ IR Range
• True Mechanical Day/Night function by ICR
• XD-DNR (2D-DNR & 3D-DNR) Noise Reduction
• ROI Encoding
• H.265/H.264/MJPEG Triple Streaming
• Secondary Video Output (CVBS)
• Remote Viewing via CMS, Internet Explorer, and iOS & Android Apps
• ONVIF Compliant
• MicroSD memory card slot for Local recording supporting up to 128GB
MicroSDXC cards
• IK10 Impact Resistance Rating
• Two Way Audio
• 12VDC & PoE (Power over Ethernet) Operation
2
Overview
Components and Accessories
Camera
Quick Guide
Screws
Hex Wrench
Drill Template
Plastic Wall Anchors
Waterproof Cap
RJ-45 Ethernet
Audio In
Audio Out
CVBS Output
Alarm I/O
RS-485
Power Cable
MicroSD Card Slot
Reset
1
2
3
4
5
6
7
8
9
1
3
4
5
6
7
2
8
9
3
Network Cable & Power Connections
First connect the Waterproof Cap to an Ethernet patch cable, then
connect the cameras ethernet adaptor. If not powering the camera with
PoE, also connect the power Cable to an approved 12VDC Power
Supply.
Weather Resistant Network Coupler
1. Loosen the nut from the Weather Resistant Network Coupler,
2. Run ethernet cable through coupler, then attach a RJ-45 connector.
3. Tighten the nut and coupler for a weather resistant seal.
ALM-COM
ALM-OPEN
ALM-INA
ALM-GND
RS485T+
RS485T-
12VDC
Optional 12VDC
Power Connection.
Not needed with PoE
4
SD Card Installation
Gap
Fixed Ring
1. Remove the fixed ring from the camera.
2. Loosen the screws of the cover of the SD card and then insert
the SD card. Then reinstall the cover ring.
5
Installation
Before beginning installation, make sure that the wall or ceiling is
strong enough to withstand 3 times the weight of the camera. The
mounting steps are as follows:
1. Remove the fixed ring
from the gap of the
camera (see Install SD
Card)
2. Drill the screw holes and
the cable hole on the
wall according to the
drill template.
3. Route and connect the
cables.
4. Fix the camera to the
wall with screws as
shown.
5. Install the fixed ring
back onto the camera.
∅5.12”
∅0.18”
3.31”
3.82”
6
LAN Configuration
The camera can be accessed on the local network either using the
IP-Tool or directly in a web browser.
Accessing the Camera Using the IP-Tool
1. Make sure the camera and PC are connected to the LAN.
2. Locate the IP-Tool installer on the included Product Documentation
CD, then install on the PC. Open the installed application.
3. Modify the IP address. The default IP address is 192.168.226.201.
Click the information of the camera listed in the above table to show
the network information on the right side. Modify the IP address and
gateway of the camera and make sure its network address is in the
same local network segment as the computer’s. Please modify the
IP address of your device according to the practical situation.
For example, the IP address of your computer
is 192.168.13.4. So the IP address of the
camera shall be changed to 192.168.13.X.
After modification, please input the password
of the administrator and click “Modify” button
to modify the setting.
** Default admin password: “123456".
7
4. Double-click the IP address and then the system will pop up the web
browser to connect IP-CAM . IE browser will download the Active X
control automatically. After downloading, a login window will pop up
as shown below:
Input the user name and password to log in.
Default user name: admin / Default password: 123456.
Directly Access Through a Web Browser
The default network settings are as shown below:
IP address: 192.168.226.201 HTTP: 80
Subnet Mask: 255.255.255.0 Data Port: 9008
Gateway: 192.168.226.1
You may use the above default settings when you log in the camera for
the first time.
1. Manually set the IP address of the PC and the network segment
should be as the same as the default settings of IP-CAM. Open the
network and share center. Click “Local Area Connection” to pop up
the following window.
Select “Properties” and then select Internet protocol according to the
actual situation (for example: IPV4). Next, click “Properties” button to
set the network of the PC.
8
2. Open the IE Browser and input the default address of IP-CAM and
confirm. The IE browser will download Active X control automatical-
ly.
3. After downloading Active X control, the login dialog box will pop up.
4. Input the default username and password and then enter to view.
WAN Configuration
Access the camera by the router or virtual server for example.
1. Make sure the camera is connected to the LAN; Then log into the
camera via LAN and go to System Congfig→Network Config→Port
menu to set up the port number.
2. Enter System Config→Network Config→IP Address menu to modify
the IP address.
4. Open the web browser and input its WAN IP and HTTP port to
access the IP-CAM.
3. Go to the router’s management interface through IE browser to
forward the IP address and port of IP-CAM in the “Virtual Server”.
9
NOTES:
10
OPTIONAL ACCESSORIES
AND RELATED PRODUCTS FOR
TRANSCENDENT IP CAMERAS
INTRODUCING OUR NEWINTRODUCING OUR NEW
VT-TNR3216PF
VT-TNR818PF
VT-TNR1646PF
• 8MP (4K) HDMI Output
• H.265 / H.264 Compression
• Full Analytic Support Including
Face Detection
• 360 Degree / Fisheye De-Warping
• Available in 8, 16, and 32 Channels
• Up to 80TB Depending on Model
• PoE Support on ALL Models
ADVANCED LEARNING NVRs
A Standalone
Solution with FULL
Analytic Support
Altri manuali per Transcendent Series
21
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Vitek Telecamera IP
Vitek
Vitek Transcendent VTC-TNB8RFA3-2 Manuale utente
Vitek
Vitek Transcendent 5 Series Manuale utente
Vitek
Vitek VTC-IR303-212NP Manuale utente
Vitek
Vitek VTD-THD2RFE Manuale utente
Vitek
Vitek VTD-IR2811DN Manuale utente
Vitek
Vitek VTC-BHOCRAZE Manuale utente
Vitek
Vitek VTC-TNB42R3F Manuale utente
Vitek
Vitek VT-PIRC2T Manuale utente
Vitek
Vitek VTC-TNB5RFS/-2 Manuale utente
Vitek
Vitek Transcendent VT-TPTZ-B10X5N Manuale utente
