Vitek VTC-C2BMS2 Manuale utente
FEATURES:
• 1/2.8” Sony® STARVIS 2.1 MegaPixel CMOS Sensor
• 2.1 MegaPixel with Full 1080p/720p HD/EX-SDI 1.0, 2.0 / TVI / AHD / CVI
/ CVBS Output
• Advanced Starlight Technology Offers Dramatically Higher Sensitivity to Light
Producing Color Images in Very Dark & Night Scenes
• CS Mount Lens Support (Lens Not Included)
• 3D-DNR Digital Noise Reduction
• True Day/Night by ICR - Dual Filter Switch
• Fully programmable True WDR (Dual Scan)
• ROI (Region of Interest) WDR achieves superior exposure compensation
specifically in exact areas of interest while reducing HDD storage space
• Advanced OSD Functions: Motion Detection, Privacy Mask, Defog, Sens-
up(~x32), Sharpness, Mirror/Flip, BLC/HLC, Deblur, Anti-Saturation, Title
Set, D-WDR
• 12VDC / 24VAC Dual Voltage Operation
VTC-C2BMS2
Premium 2.1 Megapixel 6-in-1 HD/
EX-SDI / TVI / AHD / CVI / CVBS
Box Type Camera
VITEK
VITEK
Safety Precaution
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
To prevent fire or shock hazard, do not expose the unit to rain or moisture.
To prevent electric shocks and risk of fire hazards, do NOT use other than
specific power source.
Warning :
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.
Caution :
Any changes or modifications in construction of this device which are not expressly
approved by the party responsible for compliance could void the user's authority
to operate the equipment.
Main power quality should be that of a typical commercial environment. If the user
of the model requires continued operation during power main interruption, it is
recommended that the model be powered from an uninterruptible power supply
(UPS).
The symbol is intended to alert the user to the presence of important
operating and maintenance(servicing) instructions in the literature
accompanying the unit.
The symbol is intended to alert the user to the presence of uninsulated
"dangerous voltage" within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
2 3
Safety Precaution
NOTICE
The image used in this instruction manual are processed to help comprehension
and may differ from actual video of the camera.
Avoid installing areas where has shock or vibration which results in the problems.
Pay attention to safety when running the connection cable and observe that the cable
is not subjected to heavy loads, kinks or damage and no moisture can get in.
The warranty becomes void if repairs are undertaken by unauthorized persons.
Maintenance and repair have to be carried out only by authorized service centers.
Use only a mild detergent to clean the housing.
The camera should never be operated beyond the technical specifications.
This can lead to damage and void the warranty.
The camera should never be operated in water.
3
Contents
Safety Precaution
p.02~03
Contents
p.04
Composition
p.05
Dimensions
p.05
Installation Instructions
p.06~07
p.08~23
Operating Instructions
p.24
Specifications
4 5
Dimensions
Composition
Torque Wrench:
3mm (1pc)
Dust Protection
Cap (1pc)
Operating
Instruction
Box Camera
C-mount
adaptor (Option)
2.99”
2.83”
2.99”
1.38”
3.50”
5
Part Names
Torque
Wrench
Dust
Protection Cap
No.
1
2
3
4
DC Iris
Damp(-)
Damp(+)
Drive(+)
GND
Body Case
Back focus
adjustment
Mount Holes
(Top / Bottom)
SIDE VIEW
Lens Connector
for Auto Iris lenses
PIN 1PIN 3
PIN 2PIN 4
REAR VIEW
④
① OSD Control Joy stick
② Power input terminal
(AC24V/DC12V)
③Video format selection Switch
④CVBS/HD-Analog output connector
⑤ Power LED
⑥ HD-SDI/EX-SDI output connector
③
①
⑤
⑥
②
HD-ACVBS
CONTROL
POWER
6 7
Installation Instructions
1. Remove the dust protection cap from the lens mount.
2. Screw the lens onto the camera firmly.
3. Plug the lens plug into the lens connector on the side of camera case.
4. Mount the camera to the wall or ceilling with a corresponding mounting bracket
through the camera mount holes (1/4” thread insert) on its top or bottom.
Installation and commissioning Instructions
• Make sure power is removed before installation.
• Follow this order for powering camera:
Connect the power leads to the camera (observe polarity for DC power) then
plug-in power. This will avoid damage to the camera from power surges and
improper reseting
• Care should be taken that the cable is not damaged, kinked or exposed in
hazardous areas.
• Do not expose the camera directly to a strong light source such as the sun or
spotlight.
CAUTION
• The camera has a built-in 1/2.8” sensor so using a qualified 1/2.8” C/CS mount
lens is recommended.
• Some unqualified lenses may have a smaller image circle even if the specification
is 1/2.8” so it may cause vignetting on the video.
Setting the back focus adjustment
1. Set the lens for the zoom position to WIDE and the focus position to INFINITE(∞).
2. Adjust ’Back focus’ with 3mm L-wrench until the optimum focus is
achieved.
3. Set the lens for zoom position to TELE and adjust the lens focus for best focus
.
4. Set the lens for zoom position to WIDE again, check if the focus adjustment
was the best. If not, re-adjust ‘Back focus’ slightly.
7
Operating Instructions
Power Supply Connections
OSD Control
Joystick
Using OSD Controller
Setup menu can be accessed and controlled by the OSD control joystick on the
rear of the camera unit. Five commands are available with the joystick.
The design of the OSD could be different according to the Model.
Camera can work with either 12VDC or 24VAC, dual voltage power.
Primary and secondary grounds are completely isolated to avoid possible
ground-loop problems.
1) SET (●) : Access to the menu or enter the setting.
To enter the main menu, press the Set Key down.
2) UP/DOWN (▲/▼) : Choose the desired sub-menu and to move the
cursor up or down.
3) LEFT/RIGHT (◄/►) : Set the value of the selected menu. Used to
adjust the desired menu selection and to move the cursor left or right.
Description of the OSD control operation
4) ‘ ’denotes long press down for about 2 seconds
HD-ACVBS
CONTROL
POWER
Please set the Video format selection Switch to “HD-A” when CVBS is
no longer used after finalizing camera installation.
This will allow th e WDR and 3D-NR to function when using
HD-SDI/EX-SDI.
8 9
Operating Instructions
OSD menu Table
MENU SUB MENU CONFIGURATION
LENS
EXPOSURE
BACKLIGHT
DC
MANUAL
MODE (INDOOOR, OUTDOOR, DEBLUR)
0~20
WEIGHT
MODE ROI WINDOW ZONE/USE,
H/V-POS, H/V-SIZE
NORMAL
OFF
HLC LEVEL, COLOR
H/V-POS, H/V-SIZE
BLC
WDR
TARGET-BRT LOW, MIDDLE, HIGH
LOW, MIDDLE, HIGH
COLOR
DAY & NIGHT
AWB
COLOR GAIN
EXTERN
AUTO
COLOR
B&W
SMART IR, ANTI-SAT., DELAY, IR LED CTL (AUTO, OFF)
SMART IR, ANTI-SAT., AGC THRES, AGC MARGIN, DELAY
SMART IR, ANTI-SAT.
AUTO, AUTOext, PRESET, MANUAL (C-TEMP, R/B-GAIN)
BRIGHTNESS
SHUTTER
SENS-UP
AGC
0~20
AUTO
MANUAL
(SPEED)
FLICKERLESS
0~10
OFF, x2, x4, x8, x16, x32
1/30(1/25), 1/60(1/50), 1/120(100), 1/250(200),
1/500(400), 1/1000(800), 1/2000(1600), 1/4000
(3200), 1/8000(6400), 1/15000(12800), 1/30000
(25600)
FOCUS Ast. ON, OFF
ANALOG OUT0 should be set to TVI MODE, AHD MODE or CVI MODE
to get CVBS video in sub-out. If it is set to CVBS, there is no CVBS video
in sub-out port. (SYSTEM> OUTPUT> ANALOG OUTPUT0)
If CVBS video is enabled through ANALOG OUT or Sub-out port, WDR
and 3D-NR functions are disabled in all video outputs.
It should be considered when installer adjusts the video with installation
monitor via CVBS video signal.
9
Operating Instructions
SHARPNESS
OFF, LOW, MIDDLE, HIGH
MAIN
OUTPUT
ANALOG
OUT0
ANALOG OUT0
TVI MODE 0~10
AHD MODE 0~10
TVI MODE, AHD MODE,
CVBS, CVI MODE
CVI MODE 0~10
GAMMA 0.45, 0.55, 0.65, 0.75
OFF, ON
MIRROR
DEFOG
D-WDR
MODE (AUTO, MANUAL)
LEVEL (LOW, MIDDLE, HIGH)
OFF, LOW, MIDDLE, HIGH
OFF, ON
OFF, ON
FLIP
MOTION OSD
TEXT ALARM
SYSTEM
EXIT
OUTPUT
RESOLUTION
TV SYSTEM
SAVE, CANCEL
CAM TITLE
RESET
LANGUAGE ENG, CHN(S), CHN, JPN, KOR, GER
OFF, ON
SDI OUTPUT
ANALOG OUT0
HD-SDI, EX-SDI 1.0, EX-SDI 2.0, OFF
TVI MODE, AHD MODE, CVBS, CVI MODE
1080 30P(25P), 720 30P(25P), 720 60P(50P)
US(NTSC), EU(PAL)
DET WINDOW
DET TONE
MDRECT FILL
SENSITIVITY
OFF, ON
OFF, ON
OFF, ON
0~10
0~4
WINDOW ZONE, WINDOW USE, DET
H/V-POS, DET H/V-SIZE
MOTION
OFF, RIGHT UP, LEFT DOWN
ON
PRIVACY ZONE NUM, ZONE DISP, H/V-POS, H/V-
SIZE, Y LEVEL, CB/CR LEVEL, TRANS
OFF, ON
IMAGE
ANALOG
OUT1
SDI
OUTPUT
ANALOG OUT1
SDI&CVBS
SDI&CVBS
0~10
SDI OUT HD-SDI, EX-SDI 1.0,
EX-SDI 2.0, OFF
CVBS
0~10
3D-NR
10 11
Indice
Altri manuali Vitek Telecamera di sicurezza
Vitek
Vitek VTD-C14 Manuale utente
Vitek
Vitek VTC-IRLED24A Manuale utente
Vitek
Vitek Transcend VTC-THB5R3/R2 Manuale utente
Vitek
Vitek VTC-BHOCR2812 Manuale utente
Vitek
Vitek VTC-TNT8RMEA Manuale utente
Vitek
Vitek VT-PTZ12W Manuale utente
Vitek
Vitek VT-PTZ40WH Manuale utente
Vitek
Vitek VTC-C544 Manuale utente
Vitek
Vitek VT-PIRB1 Manuale utente
Vitek
Vitek VTC-C661 Manuale utente
Vitek
Vitek VT-IR1C/24 Manuale utente
Vitek
Vitek Transcendent VTC-TNT4FLN-2 Manuale utente
Vitek
Vitek VTC-MV2NZ Manuale utente
Vitek
Vitek Transcendent VTC-TNB8RFEA-2 Manuale utente
Vitek
Vitek VTC-TNT5RFEA-2 Manuale utente
Vitek
Vitek Transcendent 5 Series Manuale utente
Vitek
Vitek Mighty VTD-MP2810WDR Manuale utente
Vitek
Vitek TRANSCENDENT VTD-TND4RMA4 Manuale utente
Vitek
Vitek VT-PIRC2H Manuale utente
Vitek
Vitek VTC-C770/WDR Manuale utente
