Vitek Transcendent Series Manuale utente

VITEK

VTD-TNMD4RFA3-2

Transcendent Series 4 MegaPixel

Gen. III Advanced A.I. Fixed IP

Vandal Dome Camera

QUICK START GUIDE

PLEASE NOTE:

Complete User Guide, Software, Tools, and Updates are

available online. Scan the QR Code or visit:

http://www.vitekcctv.com/Downloads

*Shown with optional wall

mount VT-TWMT-3

FEATURES:

• 1/3” 4.0 Megapixel Progressive Scan CMOS image sensor

• Up to 30fps live view @ 4 MegaPixel (2592x1520)

• 2.8mm Fixed Iris Lens

•Matrix IR with up to 65’ IR Range

•120dB Super Wide Dynamic Range (WDR)

• True Mechanical Day/Night function by ICR

• XD-DNR (2D-DNR & 3D-DNR) Noise Reduction

• Gen. III Advanced Analytics including Object Removal/Museum

Search, Line Crossing, and Area Intrusion Detection

• Smart H.265/H.265+/H.265/H.264/MJPEG Triple Streaming

• Remote Viewing via VMS, Internet Explorer, and iOS & Android

Apps

• ONVIF Compliant

• MicroSD memory card slot for Local recording supporting up to

256GB

• IP66 Weather Resistance

• Built-In Microphone*

• 12VDC & PoE (Power over Ethernet) Operation

2 3

Components and Accessories

Cable Connections

Overview

First connect the Weather Resistant Cap to an Ethernet patch cable,

then connect the cameras ethernet adaptor. If not powering the

camera with PoE, also connect the power Cable to an approved

12VDC Power Supply.

Weather Resistant Security Cap

Installation

Weather Resistant Network Coupler

1. Loosen the nut from the Weather Resistant Network Coupler.

2. Run ethernet cable through coupler, then attach a RJ-45 connector.

3. Tighten the nut and coupler for a weather resistant seal.

Before beginning installation, make sure that the wall or ceiling is

strong enough to withstand 3 times the weight of the camera. The

mounting steps are as follows:

2. Loosen the screws to open

the lower dome and then

loosen the lock screw to

remove the mounting base.

1. Attach the drill template to

the place where you want to

install the camera, then drill

the screw holes and 1 cable

hole according to the drill

template.

1.55”

1.57”

4.33”

3.60”

.18”

4 5

5. Replace the lower dome of the camera and make sure the light sensor can

be seen from the outside. If the light sensor is hidden, please re-adjust the lens.

Following this, secure the lower dome with the included screws.

4. Before adjusting the three-axis camera mount, preview the

camera on a monitor, then adjust as necessary achieve the

optimum viewing angle.

3. Route the cables and

connect the power & video

cables, use the rubber plug

to fill the gap of the mounting

base. then secure the

mounting base to the ceiling

or wall with screws.

LAN Configuration

The camera can be accessed on the local network either using the

IP-Tool or directly in a web browser.

Accessing the Camera Using the IP-Tool

1. Make sure the camera and PC are connected to the LAN.

2. Locate the IP-Tool installer at www.

vitekcctv.com/Downloads/Soft-

ware/Transcendent-IPTool_v2.0.2.zip

, then install on the PC. Open

the installed application.

3. Modify the IP address. The default IP address is 192.168.226.201.

Click the information of the camera listed in the above table to show

the network information on the right side. Modify the IP address and

gateway of the camera and make sure its network address is in the

same local network segment as the computer’s. Please modify the

IP address of your device according to the practical situation.

For example, the IP address of your computer

is 192.168.13.4. So the IP address of the

camera shall be changed to 192.168.13.X.

After modification, please input the password

of the administrator and click “Modify” button

to modify the setting.

** Default admin password: “123456".

IP Camera

Network Cable Network Cable

Switch

Router Computer

6 7

4. Double-click the IP address and then the system will pop up the web

browser to connect IP-CAM . IE browser will download the Active X

control. After downloading, a login window will pop up as shown

below:

Input the user name and password to log in.

Default user name: admin / Default password: 123456.

Directly Access Through a Web Browser

The default network settings are as shown below:

IP address: 192.168.226.201 HTTP: 80

Subnet Mask: 255.255.255.0 Data Port: 9008

Gateway: 192.168.226.1

You may use the above default settings when you log in the camera for

the first time.

1. Manually set the IP address of the PC. The network segment should

be the same as the default settings of IP-CAM. Open the network

and share center. Click “Local Area Connection” to pop up the

following window.

Select “Properties” and then select Internet protocol according to the

actual situation (for example: IPV4). Next, click “Properties” button to

set the network of the PC.

2. Open the IE Browser and input the default address of IP-CAM and

confirm. The IE browser will download Active X control.

3. After downloading Active X control, the login dialog box will pop up.

4. Input the default username and password and then enter to view.

WAN Configuration

Access the camera by the router or virtual server for example.

1. Make sure the camera is connected to the LAN; Then log into the

camera via LAN and go to System Congfig→Network Config→Port

menu to set up the port number.

2. Enter System Config→Network Config→IP Address menu to modify

the IP address.

4. Open the web browser and input its WAN IP and HTTP port to

access the IP-CAM.

3. Go to the router’s management interface through IE browser to

forward the IP address and port of IP-CAM in the “Virtual Server”.

5. For additional setup, features and functions, please scan

the QR code on the front page of this quick guide and

download the complete manual.

8 9

Image Sensor 1/3” 4.0 Megapixel Progressive Scan CMOS

Image Size 4 MegaPixel (2592 × 1520)

Resolution 4MP (2592 × 1520) / 3MP (2304 × 1296) / 1080P (1920 ×

1080) / 720P (1280 × 720) / D1/CIF (480 × 240)

Min. Illumination .005 [email protected], AGC on, 0 lux w/IR .0028 [email protected], AGC on; 0 lux w/IR

Lens 2.8mm Fixed Iris

Day/Night True Day/Night by ICR

IR LEDs 1 Matrix Style IR LED

IR Distance Up to 65’

Video Compression Smart H.265 / H.265+ / H.265 / Smart H.264 /

H.264+ / H.264 / MJPEG

Audio Compression G.711A / G.711U

Main Stream 4MP, 3MP, 1080P, 720P (60Hz: 1 ~ 30fps),

HFR mode: 1080P / 720P (60Hz: 1~60fps)

Sub, Third Stream 720P/D1/CIF/480×240(60Hz: ≤30fps), D1/CIF/480×240(60Hz: ≤30fps

Bit Rate 64 Kbps ~ 8 Mbps

Wide Dynamic Range 120dB Super WDR

Digital Noise Reduction 3D-DNR

Quality VBR (Five Levels of Adjustment) / CBR (Adjustable)

Other Features Defog, Backlight Control, Highlight Control, M12 Lens Mount

Image Setting ROI, Saturation, Brightness, Chroma, Contrast,

Sharpen, NR; adjustable through client

software or web browser

Gen. III Advanced Analytics Abnormal Video, Face Detection, Regional Intrusion, Regional

Entrance / Exiting, Line Crossing, Target Counting

Smart Alarm Motion detection, SD card error, SD card full

Region of Interest (ROI) Each ROI to be configured separately

Audio 1 Ch. Audio In + Built in Mic*

Local Storage Built-in micro SD card slot up to 256GB

PoE Yes , IEEE802.3af

Remote Viewing VMS / Web Browser / Mobile (iOS/Android)

Supported Browsers Internet Explorer, Chrome and Firefox with IE Tab

Connection Protocol ONVIF

Resistance IP66

Power Input 12VDC / PoE

Power Consumpt. (12VDC) 120mA (LEDs Off) / 480mA (LEDs On)

Power Consumpt. (PoE) < 6W

Working Environment -22° ~140° / < 95% Humidity

Weight .84lbs. / 380g

Dimensions 4.33” × 2.35” (110mm × 59.8mm) Dia × H

DETAILED

SPECIFICATIONS:

VTD-TNMD4RFA3-2

*Please research local, state

and federal laws regarding the

implementation of audio

surveillance.

OPTIONAL ACCESSORIES

AND RELATED PRODUCTS

FOR VTD-TNMD4RFA3-2

VT-TWMT3

Optional Wall

Mount

5.10”

6.10”

2.93”

10 11

OPTIONAL ACCESSORIES

AND RELATED PRODUCTS FOR

TRANSCENDENT IP CAMERAS

VT-TNR3216PF

VT-TNR818PF

VT-TNR1646PF

• 8MP (4K) HDMI Output

• H.265 / H.264 Compression

• Full Analytic Support Including

Face Detection and License Plate

Recognition

• 360 Degree / Fish Eye De-Warping

• Available in 8, 16, and 32 Channels

• Up to 80TB Depending on Model

• PoE Support on ALL Models

PAIR WITH OUR

ADVANCED LEARNING NVRs

A Standalone

Solution with FULL

Analytic Support

Altri manuali per Transcendent Series

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Vitek Telecamera di sicurezza

Vitek

Vitek VTC-LED667HRCB Manuale utente

Vitek

Vitek VT-PTZ12W Manuale utente

Vitek

Vitek VTD-M2HET2812 Manuale utente

Vitek

Vitek VTC-IRE70 Manuale utente

Vitek

Vitek VTC-EB25C Manuale utente

Vitek

Vitek Transcendent Series Manuale utente

Vitek

Vitek VTC-EBV49-24 Manuale utente

Vitek

Vitek VTC-C680 Manuale utente

Vitek

Vitek VTC-TNT30R3F Manuale utente

Vitek

Vitek VTD-VH49VP4 Manuale utente

Vitek

Vitek VTC-THB8R2 Manuale utente

Vitek

Vitek VTC-TNT4RMS Manuale utente

Vitek

Vitek VTC-TNB4RMA4 Manuale utente

Vitek

Vitek VTC-TNT5RFS Manuale utente

Vitek

Vitek Transcendent Series Manuale utente

Vitek

Vitek Mighty DomeColor Dome Camera Series Manuale utente

Vitek

Vitek INDOOR MIGHTY DOME - Manuale utente

Vitek

Vitek VTC-C63 Manuale utente

Vitek

Vitek VTD-C13A Manuale utente

Vitek

Vitek VTD-C410 Manuale utente

Vitek

Vitek Transcendent 5 Series Manuale utente

Vitek

Vitek TRANSCENDENT VTD-T4D6HR5MD Manuale utente

Vitek

Vitek Transcendent VTC-TNT3RFE Manuale utente

Vitek

Vitek Transcendent Series Manuale utente

Manuali Telecamera di sicurezza popolari di altre marche

Okina USA

Okina USA SIR36-870VF650LP Manuale utente

Divio

Divio NDR155PA Manuale utente

Canon

Canon VB-C500D Manuale utente

Easy Access

Easy Access EasyGuard Manuale utente

Vivotek

Vivotek FD9389-EHV-v2 Manuale utente

TUYA

TUYA COSMO W2 Manuale utente

Eusso

Eusso UNC7500-IR Guida all'installazione

urmet domus

urmet domus 1096/204 Manuale utente

VC VC20 series Manuale utente

Axis

Axis Q1614 Manuale utente

ieGeek

ieGeek DD201 Manuale utente

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuale utente

Vicon

Vicon V662-D-1 Istruzioni operative

Grundig

Grundig GCH-K0274P Manuale utente

Lorex

Lorex VANTAGE LBC7032 Manuale utente

4xem

4xem WPT Manuale utente

Samsung

Samsung SCV-3082 Manuale utente

Lumens

Lumens VC-A50PNW Manuale utente