Vivaldi KEYROUND16AF Manuale utente
vivaldigroup.it 1
User Manual
Manuale d’utilizzo
KEYSOL line
FRAMELESS SPEAKERS
WI-FI & BLUETOOTH
Coppia di altoparlanti a 2 vie wifi
2-way paired wifi speakers
KEYROUND16AF
vivaldigroup.it
2
SAFETY INSTRUCTIONS
1) Please read the instructions carefully before installation and use. Keep the manual for future reference.
2) Before installing the speakers into any ceiling/wall check the structure for weight bearing ability and
avoid contact with any wiring or plumbing that might be behind the surface area. lnstalling on soft
materials or in areas incapable of supporting the speakers weight may cause personal injury or damage to the speaker.
3) Make sure the speaker is properly secured to the ceiling/wall. Please use the proper screws, bolts, or anchors. Otherwise,
the speaker can be unsecured and cause potential damages/injuries.
4) Damage to the woofer and tweeter may occur if the speaker is dropped or hit-resulting in no sound or distorted sound.
5) Never overdrive your speakers to the point of distortion and always reduce volume before switching input sources.
6) Use only approved and certied wiring in your installation. Do not stretch or place the wire in contact with sharp objects.
7) Before removing cables make sure the power-supply to your amplier and other components is turned o.
PREPARATION
The hardware equipment listed below is needed to install the speaker
PACKING LIST
Make sure that you have received all parts according to the component checklist before to installation. lf any parts are
missing or defective, please contact your supplier.
english
Cutting Saw Wire Stripper Over Drill Pencil
Tape Measure Stud Finder Safety Glasses Ladder
Active Speaker Passive Speaker User Manual Remote
Control
Cutout
Template
Grill (x2) Power Supply Installation Tool
vivaldigroup.it 3
SPEAKER OVERVIEW
LED Indicator
Slowly ashing red: power on or reset.
Steady red: the Internet module is ready to connect.
Slowly ashing green: Wi-Fi is connecting.
Steady green: Wi-Fi is connected.
Fast ashing blue: Bluetooth is connecting.
Steady blue: Bluetooth is connected.
Steady cyan: Current audio source is RCA.
Flashing red. green and blue: The system is updating
or resetting
IR Receiver
Reset Button(WPS)
1. Press it to switch play mode.
2. Press it far 3 seconds to show the access point named:
vivaldi_keyround_xxxx (the “x” is the nal part of the MAC
ADDRESS)
3. Press it far more than 10 seconds to start
resetting with ashing red, green and blue light.
Pivoting Tweeter
Woofer
Built-in-Amplifer & Bluetooth Driver
RJ45 Ethernet Port
RCA Jack
Stereo/Mono Switch
Switch to the “stereo” position when a passive speaker
is attached. lf not, keep in “mono” position.
Volume Limiter
Limiter Enabled(50%): The volume will be limited
to the max. output 15W@8Ω
Limiter Disable(100%): The volume can be adjusted
to the max. output 30W@8Ω.
Quick-Install Spring lock Fixing
Speaker Output
Power In Jack (DC 24V/2.5A)
209mm
hole
cutout
(template
required)
100mm ceiling depth required
english
vivaldigroup.it
4
english
INSTALLATION
Power adapter
RCA
Connections
1.Cut the Speaker Hole
Place the cutout template where you are installing
the speaker. Draw the template to mark out the
speaker location with a pencil. Drill a pilot hole and cut
all of the way around the circular outline with a cutting
saw.
2.Wire the Speaker
Connect the adapter and RCA cables
(if needed) to the corresponding ports.
3.lnstall the Speaker
Adjust the spring lock with the installation
tool as shown and insert the speaker
into the hole.
4.Lock the Speaker
Lock the speaker by pressing the buttons
located on the front face of the speaker and
the dog leg will engage automatically.
5.Finish installation
Check if the LED is power on and
start the connection procedure.
vivaldigroup.it 5
english
CONNECTION
1)Wi-Fi Connecting
lnstalling Controller App
Please search “Vivaldi” to download controller app from Google Play (Android) or Apple App Store (iOS).
Connecting the Wi-Fi Speaker
Ensure the speaker is connected to the power supply. Press the WPS button to start the speaker, then you
will hear an instruction “Enter the setup mode, follow the instructions in the app to nish the setup”, and the
power indicator ash as green indicating that the speaker is ready to connect. Any wireless device
(such as phones, tablets...) is available for connecting. The Access Point name is: vivaldi_keyround_xxxx (the “x” is the nal
part of the MAC ADDRESS) for the rst 5 minutes there isn’t password(after, the access point is disable). Once connected
successfully, the power indicator will become steady green.
1. Turn on the Wi-Fi function and
connect your phone to “vivaldi_
keyround_xxxx” Wi-Fi network.
In Android OS wait the pop-up message
asking to stay connected and conrm.
2. Start the controller App Vivaldi and
wait the device appears.
vivaldigroup.it
6
english
3. Enter the Setup menu. 4. Enter Wi connection and choose
the favorite Wi network.
5. Insert the password for the se-
lected Wi network.
6. Click OK and close the APP.
Connect the Smartphone to the
WIFI network where the Keyround is
connected.
vivaldigroup.it 7
english
6. When nished, the device is suc-
cefully into the desidered network.
• When using an Ethernet cable to connect the speaker to the Router, you don’t need to do the WI-FI
setup, but only download the APP and you can nd the device.
• The router must have an active DHCP server and the UPNP functionality must be available..
• When the device starts up the access point will be activated without a password for 5 minutes, after
which the access point will be disabled..
• Between player source and RCA source, web source has priority.
• Wireless connection between Keyround and local access point may not work if you exceed
30mt in the open air, or if there are obstacles.
Note:
vivaldigroup.it
8
english
2) Airplay function
The Airplay feature is available for all compatible Apple devices.
In the device drop-down menu, click in the Airplay section and select the Keyround device from
the list. (In the example below, iOS13 system is used for your reference)
vivaldigroup.it 9
3) Bluetooth Pairing
Make sure the device is on by checking the status LED. Select the Bluetooth source in the APP or press the “MODE” button in
the remote control until the status LED turns blue. Now select from your source device (e.g. Smartphone,
tablet, laptop, etc. ) vivaldi_keyround_xxxx and perform pairing, when prompted to pin enter “2022”. Once
that the pairing is successful, you will be able to use the functionality.
Notes:
• Bluetooth functionality can only be used from 1 device at a time.
• If a pin is required for the queue enter “2022”.
• If the queue fails the rst time, restart the device and follow the instructions again. If the problem persists, press the reset
button and reset the device.
• If you are unable to connect to the previously used device, remove “Keyround” from the device list
and make the queue again.
• Bluetooth functionality does not exceed 10mt of unobstructed distance
4) RCA Connecting
1. Connect to the speaker using a dual RCA left/right cable.
2. Use the mode button on the remote or Vivaldi APP to choose RCA mode.
(PLAYER or Bluetooth Input has the priority when 3 audio inputs are connected simultaneously.)
3. The RCA mode will be activated when the indicator light shows cyan.
5) Create Stereo Pair
1. Connect the passive speaker to the 2 way connector output.
2. Slide the mono-stereo switch to the stereo position
6) Switch 3 Audio Sources
• PLAYER Mode
After connecting with the network, use Vivaldi App to play audio and the speaker will automatically work in PLAYER mode.
Or press “MODE” button of the remote for several times until the LED light turns green to switch audio source to “PLAYER”.
The Webradio, Airplay, Spotify and other function will be active automatically in this mode.
• Bluetooth Mode
Press the “MODE” button of the remote several times until the LED light turns blue or use Vivaldi App to switch
the audio source to “Bluetooth”.
• RCA Mode
Connect the speaker with an audio device like a phone or a computer by RCA cable, and press the “MODE” button on
the remote several times until the LED light turns cyan, or use Vivaldi App to switch the audio source to
“AUX in” to switch to RCA mode.
english
vivaldigroup.it
10
english
7) Remote Control
Note: CR2025 lithium coin cell battery not included.
Power On/O
Press to turn on/o the speaker.
Mute
Press to turn o the sound temporary, and press again to turn the sound back.
Volume+/-
Press to increase or decrease the sound leveI. You will hear a beep when the
volume reaches the highest or lowest level.
Treble +/-
Press to increase or decrease the high frequency response. You will hear a
beep when the treble reaches the maximum or minimum value.
Bass +/-
Press to increase or decrease the low frequency response. You will hear a
beep when the bass reaches the maximum or minimum value.
Reset
Press and hold to resume the speaker to default setting. All parameters will be reset to default values:
volume is 26; sound eect is at; treble and bass is 0.
MODE
Press to switch the audio source. Press it several times until the LED light turns green (Player mode),
blue (Bluetooth mode), or cyan (RCA mode).
EQ
Press to switch sound eects in order as Flat, Classical, Pop, Rock, Jazz, Vocal Enhanced.
Previous
Press far previous track.
Next
Press far next track.
Play/Pause
Note:
Only if the Bluetooth or Wi-Fi input is activated, the PREV, NEXT and RESET keys can work.
Tips:
The infrared remote control has eective scope of operating range which is less than 3mt and at 60 degrees angle left
for right away from the system.
Altri manuali per KEYROUND16AF
1
Indice
Lingue:
Altri manuali Vivaldi Altoparlanti
Vivaldi
Vivaldi GIADA213HPA Manuale utente
Vivaldi
Vivaldi KEOPE.S40 Manuale utente
Vivaldi
Vivaldi KEYROUND16AF Manuale utente
Vivaldi
Vivaldi ZEN315 Manuale utente
Vivaldi
Vivaldi GIADA10 Manuale utente
Vivaldi
Vivaldi FLORA16T Manuale utente
Vivaldi
Vivaldi KEOPE.M250 Manuale utente
Vivaldi
Vivaldi GIADA13L Manuale utente
Vivaldi
Vivaldi KEOPE.HP60 Manuale utente
Vivaldi
Vivaldi ROCK16T Manuale utente
