Vivo MOUNT-E-MM070W Manuale utente
White Electric TV Wall Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specications related to this product.
Instruction Manual
https://vivo-us.com/products/mount-e-mm070
SKU: MOUNT-E-MM070W
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
2
PACKAGE CONTENTS
77lbs
(35kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
WARNING!
A (x1)
Mount
B(x2)
Wall Plate Cover
C(x1)
Stencil
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualied technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specied in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED
D(x1)
TV Plate
E (x2)
VESA Bracket
F (x1)
Front Cover
G (x1)
Remote
H(x1)
Power Cord
T-A (x1)
Wrench
M-A (x4)
M5x14mm Screw
M-B (x4)
M6x14mm Screw
M-C (x4)
M6x30mm Screw
M-D (x4)
M8x30mm Screw
M-E (x4)
M8x50mm Screw
M-F (x4)
Square Washer
M-G (x8)
5mm Spacer
M-H (x8)
15mm Spacer
W-A (x6)
ST6.3x55mm Screw
W-B (x6)
Anchor
CAUTION!
DO NOT INSTALL INTO DRYWALL ALONE. VERIFY YOUR WALL CONSTRUCTION. USE WOOD STUDS TO
MOUNT. We include mounting for brick and concrete walls. If unsure, please contact us at vivo-us.
com, email at [email protected], or call us at 309-278-5303.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
W-C (x6)
Washer
3
ASSEMBLY STEPS
STEP 1
Measure the required mounting height using the
chart below. Ensure the front edge of the mantel
does not exceed 110°F (43°C).
STEP 2
Remove pre-installed Nuts (A1), Metal Washers
(A2) and Plastic Washers (A3) from Mount (A)
using Wrench (T-A).
STEP 3 (Option A)
Wood Stud Installation
Align the bottom edge of Stencil (C) with the measured height from step 1 and mark drilling locations
using a pencil. Use of a stud nder and level is recommended. Remove Stencil (C) and drill 2.2”
(55mm) deep holes using a 3/16” (4.5mm) drill bit. Attach Mount (A) to the wall with ST6.3x55mm
Screws (W-A) and Washers (W-C) using a 10mm socket.
TOOLS NEEDED
3/8” Drill Pencil
Phillips
Drill
3/16” Drill
Hammer Ruler Stud Finder
≤ 13-3/4” (350mm)
≤ 4” (100mm)
≤ 7-7/8” (200mm)
≤ 11-3/4” (300mm)
≥ 9-7/8” (250mm)
≥ 7-7/8” (200mm)
≥ 3-1/8” (80mm)
≥ 11-3/4” (300mm)
T-A
10mm Socket
C
A
W-C
W-A
4
STEP 4
Plug Power Cord (H) into Mount (A). Place Power Cord (H) into the slot as shown and snap Wall Plate
Covers (B) in place.
STEP 3 (Option B)
Concrete/Brick Installation
Align the bottom edge of Stencil (C) with the measured height from step 1 and mark drilling locations
using a pencil. Use of a level is recommended. Remove Stencil (C), drill 2.4” (60mm) deep holes using
a 3/8” (10mm) drill bit, and insert Anchors (W-B) into the holes. Attach Mount (A) to the wall using
ST6.3x55mm Screws (W-A) and Washers (W-C) and a 10mm socket.
A
A
C
W-B
W-B
W-C
W-A
5
STEP 5
Plug Power Cord (H) into a wall outlet. Press and hold the down button on Remote (G) until the arm is
fully lowered. Remove and discard the plastic wedge (A4).
WARNING! The arm is not able to fully raise and may
cause damage to the mount if the wedge is not removed
STEP 6
Remove the nut from each VESA Bracket (E) and ip open the clip.
1
1
2
3
6
STEP 7
Attach VESA Brackets (E) to the back of the TV using
combination of Screws (M-A - M-E), Washers (M-F)
and Spacers (M-G, M-H) appropriate for your TV. The
bottom edge of the VESA brackets should be greater
than 7-7/8” (200mm) above the bottom edge of the
TV.
STEP 9
Hang the TV with VESA Brackets (E) onto TV Plate (D). Close the clips, and secure using the
previously removed nuts. Tighten with Wrench (T-A).
STEP 8
Place previously removed Plastic Washers (A3) on Mount (A). Attach TV Plate (D) to Mount (A) using Nuts
(A1) with Metal Washers (A2). Make sure TV Plate (D) is level, and tighten nuts using Wrench (T-A). Press
Front Cover (F) onto the front of TV Plate (D).
A
T-A
E
D
T-A
7
STEP 10
Manage cables using the cable clips on the arm. Use Remote (G) to raise and lower Mount (A). The TV
may be manually swiveled to the le and right.
CAUTION: To avoid injury, do not place hand in the arm while operating.
A
G
LAST UPDATED: 04/05/2022
REV1
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303
Indice
Altri manuali Vivo Supporto TV
Vivo
Vivo MOUNT-VW100T Manuale utente
Vivo
Vivo MOUNT-VW63G Manuale utente
Vivo
Vivo STAND-TV00Y Manuale utente
Vivo
Vivo MOUNT-SF05L Manuale utente
Vivo
Vivo MOUNT-VC55A Manuale utente
Vivo
Vivo MOUNT-SF05L Manuale utente
Vivo
Vivo STAND-TV04M Manuale utente
Vivo
Vivo STAND-V002T/W Manuale utente
Vivo
Vivo STAND-TV00Y Manuale utente
Vivo
Vivo MOUNT-SONOS3T Manuale utente
Vivo
Vivo MOUNT-VW080P Manuale utente
Vivo
Vivo Mount-E-FD55 Manuale utente
Vivo
Vivo MOUNT VW01 Manuale utente
Vivo
Vivo MOUNT-E-FD70W Manuale utente
Vivo
Vivo STAND-TV00M2 Manuale utente
Vivo
Vivo VESA STAND-VAD1B Manuale utente
Vivo
Vivo MOUNT-VW02A Manuale utente
Vivo
Vivo STAND-TV55T/W Manuale utente
Vivo
Vivo MOUNT-M-FD27 Manuale utente
Vivo
Vivo STAND-TV07A Manuale utente
