Vonets VM300 Istruzioni utente
VONETS —— WiFi Module
WiFi Module VM300/VM5G
Quick Setting Guide
VONETS —— WiFi Module
Declaration
Copyright © 2019 Shenzhen HouTian Network Communication Technology Co.,Ltd
All rights reserved, with retained ownership Without Shenzhen HouTian Network
communication Technology Co.,Ltd written authorization, any company or personal can’t
copy, writer or translation part or all contents. Can’t do commodity distribution for any
commercial or profitable purposes by any ways(electricity, mechanical, photoprint, record or
other methods).
VONETS is the registered trademark of Shenzhen HouTian Network Communication
Technology Co.,Ltd. The other all trademarks or registered trademarks mentioned in this
documents are belong to the individual owners. The product specifications and information
technology mentioned in this manual are just for reference, if any updates, without other not
ice. Except for special agreements, this manual is just for user guidance, any statements, in
formation and so on in this manual can’t constitute the warranty of any forms.
Form 1
Transmission Distance Parameters Form
Model
No-barrier point to
point Transmission
Distance
Transmission
Rate (Mbps)
Band
VM300
80m--100m
300
2.4G
VM5G
600m--700m
300+900
2.4G/5G
Form2
Power Supply Parameters List
Model
Power Supply Voltage
Input Power
Typical Power
Supply
VM300
DC5--15V
≥5W
5V/1A
VM5G
DC5--15V
≥10W
5V/2A
VONETS —— WiFi Module
Contents
Chapter 1 Application Mode..................................................................... 1
1.1 Bridge + Repeater Mode...................................................................................................................... 1
1.2 Router Mode............................................................................................................................................... 2
Chapter 2 Bridge+Repeater Mode Configuration Instruction.... 3
2.1 Device Connection ................................................................................................................................. 3
2.2 Bridge+Repeater Application Configuration........................................................................... 4
2.3 AP Application Configuration ........................................................................................................ 7
Chapter 3 Router Mode Configuration Instruction......................... 9
3.1 Change device mode............................................................................................................................... 9
3.2 WAN port setting .................................................................................................................................11
3.2.1 WAN/LAN exchange.........................................................................................................................11
3.2.2 WAN Port connection method................................................................................................11
3.2.3 WAN port wired connect network——DHCP ....................................................................12
3.2.4 WAN port wired connect network——PPPoE ..................................................................12
3.2.5 WAN port wireless connect network---- WiFi .........................................................13
3.3 Set WiFi hotspot parameters ......................................................................................................14
Appendix Frequently Asked Questions ................................................ 16
VONETS —— WiFi Module
1
Chapter 1 Application Mode
1.1 Bridge + Repeater Mode
There are three application modes for the bridge mode of VONETS module: WiFi
repeater, WiFi bridge and WiFi AP.
⚫WiFi Repeater:
VONETS module as WiFi Repeater, it must be configured to source WiFi hostpot
parameters, can be used to extend the wireless signal coverage of existing APs
or wifi router .
⚫WiFi Bridge:
VONETS module as WiFi bridge, it must be configured to source WiFi hotspot
parameters, can be used for devices only with Ethernet ports to access wireless
networks.
⚫WiFi AP：
VONETS module as WiFi AP, it can achieve wireless access to wired LAN, no
configuration required, plug and play.
VONETS —— WiFi Module
2
1.2 Router Mode
⚫VONETS module as WiFi router
The Ethernet port of VM300 module defaults to WAN port. The Ethernet cable defaults
to the LAN port. WAN and LAN ports are interchangeable.
The Ethernet cable of VM5G module defaults to LAN port, you must set “WAN/LAN
interchange”so that the Ethernet cable is WAN port to use the broadband dialing
function.
⚫VONETS module is used as a wireless router. WAN port can be set to connect to the
WiFi hotspot for use as a secondary router.
VONETS —— WiFi Module
3
Chapter 2 Bridge+Repeater Mode Configuration
Instruction
2.1 Device Connection
Power on VONETS module by 5V/2A power supply, then connect to PC, there are two
connection ways as below:
A. Computer is wired connected to LAN port of VONETS module;
（Recommend Method）
VONETS —— WiFi Module
4
B. The computer wirelessly connects to the WiFi signal of VONETS module, its
default hotspot parameters are as follows:
WiFi SSID
WiFi Password
VONETS_2.4G_****
12345678
VONETS_5G_****
12345678
(After the WiFi parameters are configured, the WiFi will be disconnected, that is normal.)
2.2 Bridge+Repeater Application Configuration
The configuration steps of VONETS module for WiFi repeater and WiFi bridge are
basically the same, so this manual combines the configuration instructions of the two
application modes.
1. After computer is connected to VONETS module, open browser, input configured page:
http://vonets.cfg (or IP: 192.168.254.254), then press Enter;
2. Input User name and Password in login page (both are “admin”), click “Login”
button to enter configured page;
3. “Scan Hotspots”, choose the source hotspots, click “Next”;
VONETS —— WiFi Module
5
4. Input “Source wireless hotspot password”, click “Apply”;
⚫IP layer transparent transmission (factory default), transparent transmission
of IP layer data, can meet most of WiFi bridge applications;
⚫MAC layer transparent transmission, transparent transmission of all data above
the MAC layer (link layer) and MAC layer, including IP layer data. MAC
transparent transmission can solve some special applications for MAC layer
encryption, such as GoPro camera, Cisco AP, Hikvision monitoring system, etc;
⚫The option “The configuration parameters of WiFi repeater security is
synchronized with source hotspot” is default ticked, it means the SSID of
VONETS repeater is associated with the SSID of the source hotspot, and the WiFi
password is the same as the password of the source hotspot;
⚫Disable hotspot, if you select “Disable hotspot” on the right side of the
SSID, the device will not transmit the corresponding hotspot and can only be
used as a bridge application;
⚫Advanced Setting,include Hot spot authentication match mode, WiFi Signal Motion
Detection and SSA Signal strength alarm threshold,these options here can be
kept unchanged, for instructions on this option, go to www.vonets.com and
download the “V Series WiFi Bridge Advanced Features Instruction”;
VONETS —— WiFi Module
6
5. Click “Reboot”, VONETS module will connect to the configured WiFi hotspot
automatically, if connection is successful, the WiFi LED light will flash quickly;
Remark 1:
LED Light Form
Model
Blue Light
Green Light
Yellow Light
VM300
2.4G WiFi Connection
Status Light
Ethernet Cable
Connection Status Light
/
VM5G
2.4G WiFi Connection
Status Light
5G WiFi Connection
Status Light
Ethernet Cable
Connection Status
Light
①VONETS module is not connected to any hotspot, WiFi connection status light
will flash quickly;
VONETS —— WiFi Module
7
②VONETS module is connected to hotspot successfully, WiFi connection status
light will quick flash;
③VONETS module is connected to hotspot successfully, but hotspot signal
strength is less than 50% greater than 10%, WiFi status light will pause flash
and flash;
④VONETS module is connected to hotspot failed, WiFi connection status light
will flash slowly.
2.3 AP Application Configuration
VONETS module can be configured as an AP application. The wireless terminal device
can connect to VONETS module hotspot to connect to the network; however, it is best
to change its WiFi name and password for network security.
1. Log in to the configuration page http://vonets.cfg (or IP: 192.168.254.254) in
your computer browser, both user name and password are “admin”
2. Revise WiFi name: Jump to “WiFi Repeater”---- “Basic Settings”, enter new WiFi
name in “WiFi Repeater (SSID)”, click “Apply”;
3. Revise WiFi password, in “WiFi Repeater”----“WiFi Security”, enter new WiFi
password in “Pass Phrase”, click “Apply”;
Questo manuale è adatto per i seguenti modelli
1
Indice
Manuali Scheda di rete popolari di altre marche
Buffalo
Buffalo AirStation WLI-PCM-L11GP Manuale utente
National Instruments
National Instruments NI 9234 Manuale utente
Hama
Hama 49276 Manuale utente
Linksys
Linksys WCF54G - Wireless-G Compact Flash Card Manuale operativo
Compaq
Compaq Wireless LAN 100 Manuale utente
Bose
Bose PowerMatch Dante Manuale utente