VOTOMY VT360 Manuale utente
BLUETOOTH SPEAKER
01
09
16
23
30
Deutsch
España
Italiano
Francais
1x VT360 Wireless Stereo Speaker
1x Micro USB charging Cable
1x After-Sale Card
1x User Manual
1x Lanyard
•
•
•
•
•
Power Input: 5V/2A Aux In
Power on/off
LED Indicator
Bluetooth
Decrease Volume/Previous Song
Increase Volume/Next Song
Pause/Play
Power Output: 5V/1A
Before using for the rst time, please fully charge the built-in
ba battery.
Connect the Micro USB charging Cable (included) between
the " " Micro USB charging port on the speaker, and a USB
port on a computer or USB AC adapter.
•
•
Press the " " button until you hear a rising tone and the LED
indicators turn on.
Press the " " button until you hear a decending tone and the
LED indicators turn off.
Note: When the battery has less than 10% power remaining, the
speaker will power off automatically.
When your speaker is turned off, press and hold the " "
button until you hear a rising tone and the LED indicators turn
blinking blue.
Go to the Bluetooth settings on your mobile device, search
and select "VT360" from the list of device(s).
Once paired, the LED indicators turn solid blue.
•
•
•
Make sure that the speaker is within 10 meters from your mobile
device.
Play/ Pause
Decrease Volume
Increase Volume
Next Song
Previous Song
Bluetooth /TWS Mode Pairing
Click
Click
Click
Click
Press and Hold
Press and Hold
Answer an incoming call
Reject an incoming call
End the current call
Press " " and " " buttons simultaneously until LED Indicator
fast blinking blue to disconnect the currently connected device,
and restart a new Bluetooth-pairing status.
Click
Press and Hold
Click
Note: When powered on, the speaker automatically reconnects to
the previously connected device. (The speaker has memories of up to
8 paired devices.)
The speaker will automatically shut down after 10 minutes if not in use.
The TWS technology enables you to use two speakers pairing
via Bluetooth to create a wireless dual-channel system to
deliver true stereo sound effect.
Long press the " " button to enter into the true wireless
stereo pairing mode as a master speaker. If one of them fails,
clean up the pairing information.
•
Enable bluetooth on your device and connect to "VT360",
stereo sound will play from both speakers.
•
Power on the speaker.
Using the AUX Cable, connect your external device to the
Aux in port on the speaker.
The speaker will automatically turn into AUX IN mode, the
LED Indicators turn solid green.
•
•
•
Long press the button " " on the speaker until LED Indicator
fast blinking blue to disconnect the TWS connection.
Once paired, the MAIN speaker LED indicator ashes blue
slowly.
•
Insert the AUX cable plug as AUX IN mode.
Pull out the AUX cable plug and switch to bluetooth mode.
AUX IN mode, the LED indicator keep solid green.
•
•
•
IMPORTANT NOTE: To ensure the speaker is prepared to use for
water-resistant, please remove all the connected cables and close the
port protection cover tightly.
Reset the speaker: If the control buttons are not working properly,
please disconnect the charging cable, long press the button " " and
hold it for 10 seconds until the LED light off.
Bluetooth version: 5.0
Support: A2DP V1.3; AVRCP V1.6, HFP V1.7
Wireless working distance: 10 meters
Power output: 15W x 2
Driver unit: Φ55mm
Frequency response: 70Hz~18kHz
Signal-to-noise ratio: ≥70dB
DC input voltage/current: Micro USB DC 5V/2A
Playtime: ≥12 hours (50% volume)
Battery charge time: ≤4 hours (5V/2A)
Dimensions: 204x75x85mm / 8.03x2.95x3.34inch
Weight: 712g
•
•
•
•
•
•
•
•
•
•
•
•
Keep the speaker and its accessories away from the reach of
children to avoid choking or strangling.
Keep the speaker away from re, water, liquids, extreme heat,
and strong magnetic elds to avoid damage to the device.
Do NOT use this speaker at high volume for extended period
of time as this may cause permanent hearing damage or
hearing loss.
•
•
•
Altri manuali per VT360
1
Indice
Lingue:
Altri manuali VOTOMY Altoparlanti
