Votronic 2065 Manuale utente
Installation and Operating Manual
CONTROL Unit for MobilPOWER Inverter SMI (-NVS) Sinus No. 2065
On/Off Control Unit, 12 V and 24 V
The ON/OFF Control Unit allows automatic switching on and off of the MobilPOWER Inverter of series SMI Sinus by
means of the D+ connection of the alternator.
The inverter can also be switched on or off by supplying 12 V or 24 V battery voltage to the terminal On/Off via main
switch, timer or simple on-off switch.
The control panel existing at the inverter is not required, since the unit is now switched on or off by the ON/OFF control
unit. If the control panel shall be still used as display panel, it can be removed from the unit to be used as remote control.
The delivery scope of the inverter includes a control cable of 5 m length for connection.
Please read these mounting instructions prior to connection and start-up.
Mounting:
•Disconnect the power supply: Unscrew the connection cable of the inverter from the positive pole of the battery.
•Remove the control panel of the inverter, and separate the control cable from the inverter.
•Insert the delivered control cable of 30 cm length, and connect it to the female connector Inverter at the ON/OFF
control unit.
•Install the ON/OFF control unit next to the inverter.
•Wire the terminal ON/OFF to the ON/OFF control unit with the desired switching signal or control signal.
•Make the desired adjustments by means of the microswitch at the inverter (see page 2).
•Re-establish the power supply: Screw the connection cable of the inverter firmly down to the positive pole of the
battery.
OPTION: Remote Control
Connect the control panel to the female connector Remote at the ON/OFF control unit using the control cable of 5 m
length.
The ON/OFF control unit will only be activated and released, if the inverter is separated from mains, that is,
the unit has been separated from the battery.
Function:
If voltage is supplied to the control input of the ON/OFF control unit, the inverter will be starting after 3 seconds waiting
time. Identical to the switching-on process, also the switching-off process is effected with a time-delay of approx. 3
seconds.
In connection with the ON/OFF control unit the inverter will always start in continuous operation. The switch function at
the control panel is restricted, which means that manual switching on and off of the inverter is not possible any longer.
However, in case of failure, this switch can be used to reset the unit, and the inverter can be switched on by means of the
ON/OFF control unit.
If the control voltage is removed from control input D+ of the ON/OFF control unit, the inverter will be switched-off in any
case.
--2--
How to set the operating modes:
The micro slide switches for adjustment of the operating modes are located at the inverter behind the control panel.
The functions of the ON/OFF control unit can only be used, if microswitch 4 (Run Mode)
had been placed to position Always On.
Microswitch 3 (Power Save) is used to
switch the Power Save Mode on or off (see operating manual
inverter).
In connection with the ON/OFFF control unit,
microswitch 2 (Power Save Time) has no function.
Microswitch 1 (Power Save Load) is used to set the thresholds for
operation in Power Save Mode between
25 W and 60 W (see operating manual inverter).
View: Display panel removed
Declaration of Conformity:
In accordance with the provisions of Directives 2014/35/EU, 2014/30/EU, 2009/19/EC, this
product complies with the following standards or normative documents:
EN55014-1; EN55022 B; EN61000-6-1; EN61000-4-2; EN61000-4-3; EN61000-4-4;
EN62368-1; EN50498.
The product
must not be
disposed of in
the household
waste.
The product is RoHS compliant.
It complies with the directive
2011/65/EU for Reduction of
Hazardous Substances in electrical
and electronic equipment.
Subject to misprints, errors and technical modification without notice.
All rights reserved, particularly the right of reproduction. Copyright VOTRONIC 02/2019.
Made in Germany by VOTRONIC Elektronik-Systeme GmbH, Johann-Friedrich-Diehm-Str. 10, 36341 Lauterbach/GERMANY
Phone: +49 (0)6641/91173-0 Fax: +49 (0)6641/91173-20 E-Mail: info@votronic.de Internet: www.votronic.de
Technical Data:
Nominal Voltage (DC): 12 V / 24 V
Control Input, max. Voltage: 32 V
Control Input (ON Recognition): from 10 V to 32 V
Control Input (OFF Recognition): less than 1.0 V
Dimensions (mm): 75 x 47 x 20
Weight: 40 g
Ambient Conditions, Humidity of Air: max. 95 % RH, no condensation
Delivery Scope: Available Accessories:
•ON/OFF Control Unit - Connection Cable, 5 m Length, as Extension, Order No. 2005
•Connection Cable, 6-Poles, Length 30 cm
Indice
Altri manuali Votronic Unità di controllo
Manuali Unità di controllo popolari di altre marche
Festo
Festo Compact Performance CP-FB6-E Manuale elenco delle parti
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuale utente
JS Automation
JS Automation MPC3034A Manuale utente
JAUDT
JAUDT SW GII 6406 Series Guida rapida
Spektrum
Spektrum Air Module System Manuale utente
BOC Edwards
BOC Edwards Q Series Manuale utente
