WANHAO Duplicator 3/4 Manuale utente
WANHAO 3D PRINTER
USER MANUEL
Tel: +86-579-82346658
Email: [email protected]
Web: WWW.WANHAO3DPRINTER.COM
Unboxing and hard ware set up
Unboxing and Hardware Setup
Unboxing and Hardware SetupUnboxing and Hardware Setup
Unboxing and Hardware Setup
We packaged your Duplicator 3/4very carefully at the Wanhao Botcave -- we hope you’ll read this
guide and be just as careful unpacking it In fact, you should always be really careful with The
Duplicator 3 Here are a few things to keep in mind
Safety Information
Safety InformationSafety Information
Safety Information
1.1 Caution: The Duplicator 3/4generates high temperatures and includes moving parts that can cause injury. Never reach inside
The Duplicator 3/4while it is in operation and allow time for The Duplicator 3/4to cool down after operation.
The Duplicator 3/4is sensitive to electrostatic discharge. Make sure you don't have a static charge on you by touching a grounded
object before operating The Duplicator 3/4or attempting any adjustments. If opening The Duplicator 3/4for service ensure that the
power supply is turned off and the cord is disconnected.
Package Conte
Package ContePackage Conte
Package Contents
ntsnts
nts
Here are the items that should be found in the
Here are the items that should be found in the Here are the items that should be found in the
Here are the items that should be found in the Duplicator 3/4
Duplicator 3/4Duplicator 3/4
Duplicator 3/4package:
package:package:
package:
-The Duplicator 3/4
The cardboard box set into the top of The
The cardboard box set into the top of The The cardboard box set into the top of The
The cardboard box set into the top of The Duplicator 3/4
Duplicator 3/4Duplicator 3/4
Duplicator 3/4is the Accessory Box In it, you’ll find:
is the Accessory Box In it, you’ll find:is the Accessory Box In it, you’ll find:
is the Accessory Box In it, you’ll find:
-Single or Dual Step extruder MK7 +
-1x or 2x spool holders
-Feet and Bolts Kit
-Hex Wrench Kit
- 1 x SD card
-1 x Wanhao platform tape
Inside The Duplicator 3's frame and underneath the build platform:
Inside The Duplicator 3's frame and underneath the build platform:Inside The Duplicator 3's frame and underneath the build platform:
Inside The Duplicator 3's frame and underneath the build platform:
-1 kg White ABS filament
-1 kg black ABS filament (dual Step extruder MK7+ models only)
Underneath The Duplicator 3:
Underneath The Duplicator 3:Underneath The Duplicator 3:
Underneath The Duplicator 3:
-Power supply
-Power supply cable
-USB A to B cables
-1x or 2x filament guide tubes
Unboxing
UnboxingUnboxing
Unboxing
2.1 The Duplicator 3/4is packed very tightly and carefully -- take your time unpacking it. In this section the names of important parts
of the machine will be in bold type.
First place The Duplicator 3's box on the ground next to a clean flat workspace. Discard the top cardboard insert if you haven’t
already. Now remove the inner cardboard box -- the one that fits around the outside of The Duplicator 3. 2.2
You’ll be able to see the top of The Duplicator 3/4now as well as some cardboard boxes and packaging. The large box with the thick
black cable leading into it is the Accessory Box
Accessory BoxAccessory Box
Accessory Box where you’ll find the Step ex
Step exStep ex
Step extruder
truder truder
truder MK8+
MK8+MK8+
MK8+ and other crucial things. Leave it in place
for now.
Note: the black cable is not a handle! Never lift he
Note: the black cable is not a handle! Never lift he Note: the black cable is not a handle! Never lift he
Note: the black cable is not a handle! Never lift he Duplicator 3/4
Duplicator 3/4Duplicator 3/4
Duplicator 3/4by the black cable.
by the black cable.by the black cable.
by the black cable. 2.3
Now we’re going to take The Duplicator 3/4out of its box. 2.4 Lift it up from the outside. Grasp the upper frame carefully and avoid
touching the internal belts and rods. Gently pull The Duplicator 3/4out of its packaging and place it on your work surface.
In the packaging underneath your Duplicator 3/4you’ll find the Power Supply
Power SupplyPower Supply
Power Supply and cable
cablecable
cable as well as your USB A to B
USB A to B USB A to B
USB A to B
cable
cablecable
cable andF
FF
Filament Guide ube(s)
ilament Guide ube(s)ilament Guide ube(s)
ilament Guide ube(s). Take these out and put them aside.
Now let’s go back to the ever-important Accessory Box
Accessory BoxAccessory Box
Accessory Box. Open the top flap and remove the insert. 2.5
Follow the thick black cable to the Step ex
Step exStep ex
Step extruder
truder truder
truder MK8+
MK8+MK8+
MK8+. Reach in grasp the Step extruder by its sides and remove it from the
box. 2.6 Leave it in its protective bag and set it down safely out of the way on your work surface.
Now you can clear away the cardboard inserts and remove the Accessory Box
Accessory BoxAccessory Box
Accessory Box from The Duplicator 3. Be careful of the black
plastic Step ex
Step exStep ex
Step extruder
truder truder
truder MK8+
MK8+MK8+
MK8+
Mount
MountMount
Mount.
You should be able to see the build platform: it’s an aluminum plate covered in Kapton tape and attached to the rods by two black
plastic arms. This is where your prints will form.
You’ll need to raise the platform to finish unpacking. You can either turn the threaded screw just behind The Duplicator 3/4logo or
grasp the build platform firmly on both sides and move it up with gentle pressure.
Move the platform up as far as you can; it should almost reach the black S
SS
Step
teptep
tep
ex
exex
extruder
truder truder
truder MK8+
MK8+MK8+
MK8+
Mount
MountMount
Mount. 2.7
Underneath the build platform you’ll see one or two boxes of Wanhao filament
Wanhao filamentWanhao filament
Wanhao filament. Carefully remove these as well as the remaining
packing material. It’s easiest if you remove the packing material first.
You have now finished unpacking your Duplicator 3! We’re really proud of it! Also we recommend that you keep the box that it was
shipped in for future transport and long-term storage.
The Duplicator 3/4Diagram
Before we continue, let’s familiarize ourselves with some of the main features of The Wanhao
Duplicator 3
3 1 Front:
Front:Front:
Front:
1.
Step extruder MK8+ (attached to mount)
2.
Build Platform
3.
LCD Interface Panel
4.
Guide tubes
5.
SD Card slot (on side panel)
3 2 Back:
Back:Back:
Back:
6.
Power switch
7.
Power input
8.
USB input
9.
Reset switch
10.
Right and left spool holders
Initial Hardware Setup
With the build platform raised you have a clear view of the black cable that leads from the electronics cavity to the build platform.
Attached to the cable is a black c
cc
cable retainer clip
able retainer clipable retainer clip
able retainer clip. Now find the small round hole slightly to the left of center at the rear of the wooden
plate below the build platform. The clip should snap easily into place.
Now we’re going to bolt the Step
Step Step
Step extruder
extruderextruder
extruder
MK8+
MK8+MK8+
MK8+ into place. Lower the build platform all the way by turning the threaded screw behind
the platform or by grasping the black plastic arms at the sides of the platform and pushing down with gentle but steady pressure.
Now go back to the Accessory Box
Accessory BoxAccessory Box
Accessory Box and locate your
Bolts Kit
Bolts KitBolts Kit
Bolts Kit. Remove the two black bolts from the kit. Next locate your Hex Wrench
Hex Wrench Hex Wrench
Hex Wrench
Kit
KitKit
Kit and find the hex wrench that fits the bolts.
Grasp your Step ex
Step exStep ex
Step extruder
truder truder
truder MK8+
MK8+MK8+
MK8+ by the sides and take it out of its protective bag. Place it on the Step
Step Step
Step extruder
extruderextruder
extruder
MK8+
MK8+MK8+
MK8+
Mount
MountMount
Mountso the
bolt holes line up and the fans face forward. Secure it with the bolts and wrench. 4.2
While you still have the Feet and Bolts Kit
Feet and Bolts KitFeet and Bolts Kit
Feet and Bolts Kit at hand remove the four feet and fit them onto the bottom of The Duplicator 3. They work
best on the side panels.
Now grab the Spool holder(s)
Spool holder(s)Spool holder(s)
Spool holder(s). If you have two spool holders put one on each side. If you have only one put it on the left side as you
face the rear of The Duplicator 3.
To install a spool holder tilt it up to fit through the rectangular opening and then tilt it back down to lock it into place. 4.4
Indice
Altri manuali WANHAO Stampante 3D
WANHAO
WANHAO Duplicator 5S Manuale utente
WANHAO
WANHAO Duplicator 7 Plus Manuale utente
WANHAO
WANHAO Duplicator i3 Manuale utente
WANHAO
WANHAO DUPLICATOR 9 Manuale utente
WANHAO
WANHAO Duplicator 10 Manuale utente
WANHAO
WANHAO DUPLICATOR 7 Manuale utente
WANHAO
WANHAO DUPLICATOR I3 MINI Manuale utente
WANHAO
WANHAO D9 Manuale utente
WANHAO
WANHAO Duplicator 5S Manuale utente
WANHAO
WANHAO Duplicator 4 Manuale utente
WANHAO
WANHAO DUPLICATOR 7 Manuale utente
WANHAO
WANHAO GADOSO GR1 Manuale utente
WANHAO
WANHAO CGR Series Manuale utente
WANHAO
WANHAO Duplicator 6 Manuale utente
WANHAO
WANHAO DUPLICATOR 9 Manuale utente
WANHAO
WANHAO Duplicator i3 Manuale
WANHAO
WANHAO Duplicator i3 Manuale utente
WANHAO
WANHAO D12 300 Manuale utente
WANHAO
WANHAO DUPLICATOR 9 Manuale utente
WANHAO
WANHAO Duplicator 7 Plus Manuale utente
