Water Soft ISOBAR II Manuale utente

Filter Manual

Installation / Operation Manual

www.watersoftinc.com

Online at

General Specifications............................................................ Page 3

Filter Media................................................................................ Page 4

Installation Requirements....................................................... Page 5

Programming the Control Valve............................................... Page 9

Utilizing Bluetooth................................................................... Page 11

Master Programming............................................................... Page 14

Control Valve Powerhead Assy. ISO II & ISO III.................... Page 15

Valve Body Assembly ISO II.................................................... Page 16

Bypass Assembly ISO II.......................................................... Page 17

Valve Body Assembly ISO III................................................... Page 18

Bypass Assembly ISO III.......................................................... Page 19

Service Instructions................................................................. Page 20

Troubleshooting........................................................................ Page 21

Error Codes.............................................................................. Page 22

Warranty Information............................................................... Page 23

FCC Compliance Statement:

http://www.chandlersystemsinc.com/files/FCC_Compliance_Statement.pdf

Industry Canada Compliance Statement:

http://www.chandlersystemsinc.com/files/Industry_Canada_Compliance_Statement.pdf

WARNING

Lubricants

Do NOT use Vaseline, oils, hydrocarbon lubricants or spray silicone anywhere! Petroleum base lubricants will cause

swelling of o-rings and seals. The use of other lubricants may attack plastic Noryl®. It is recommended that Dow Corn-

ing® silicone grease be used as a lubricant for all control valves. Dow Corning® 7 Release Compound is used in the

manufacture of Chandler Systems control valves. (Part # LT-150)

Sealants

Pipe dope and liquid thread sealers may contain a carrier that attacks some plastic materials. It is recommended that

Teflon® tape be used to seal plastic Noryl® threaded fittings.

Filter Specifications

1 See “Filter Media” section for selection of proper media for your filtration application.

2 Use of a flow control in the Service line is highly recommended.

3 Caution should always be used in sizing filters! Always choose a unit by first satisfying the Backwash Flow Rate requirement above.

Consult the factory or your field sales person with questions.

General Specifications G9

G9-3

G10

G10-3

G12

G12-3

G13

G13-3

G14

G14-3

Filtration1Less Filter Media

Filter Media Capacity (cu ft) 1.0 1.5 2.0 2.5 3.0

Mineral Tank (Vortech ™) 9 X 48 10 X 54 12 X 52 13 X 54 13 X 65

Service Flow Rate - Continuous2(gpm) 45689

Service Flow Rate - Intermittent2(gpm) 6 7 8 10 11

Backwash Flow Rate3(gpm) 5.0 5.0 6.0 7.0 7.0

Gallons Used / Backwash 100 100 120 140 140

Space Required 9 X 9 X 56 10 X 10 X 62 12 X 12 X 60 13 X 13 X 62 13 X 13 X 74

Approximate Shipping Weight (lbs) 27 32 35 40 49

Filter Media

Media Ship Wt.

(lbs) Description Handles... Used in...

SmartBlend

SB75

SB10

Granular / White-Black / Filter Ag Plus and Katalox Light

/ Max life expectancy about 8-10 years but is dependent

upon pH

Sediment

Iron (clear & red)

Manganese (clear & red

Sulfur Particles

PROVECTR®

Soft ‘N’ Filter w/ Mid-Vortech4

CENTURI

Neutralizer

NE50

NE75

NE10

Granular / White / Sacrificial to water with pH, 7.0 / Max

pH correction to 7.2 / Lowest pH application 5.8 / Must be

replenished about every 3-6 months

Sediment

pH correction

“G” Series Filters

“U” Series Filters2

Soft ‘N’ Filter w/ Mid-Vortech

Neu-Cor™

NC75

NC10

Granular / Semi-round / White & Off-white / 70%-30%

Blend of Neutralizer & Corosex®must be replenished on a

regular basis since both components are sacrificial to low

pH / Use on pH levels as low as 5.06

Sediment (downflow)

pH Correction

“G” Series Filters

“U” Series Filters

Corosex®

CX75

CX10

103

Semi-round / Off-White / Magnesium Oxide / Extremely

reactive to pH dissolving rapidly adding alkalinity / NEVER

use 100% Corosex®in a filter as it will “cement” / 30%

Corosex®- 70% Neutralizer is best blend for correcting

low pH / Will raise pH from lows around 5.0 to as high as

9.0+ / Must be replenished frequently / consult factory with

specific application questions

Sediment (downflow)

pH Correction

“G” Series Filters5

“U” Series Filters5

Coconut Shell Carbon

CN75

CX10

103

Black / High carbon-Low ash content. Practical for ordinary

taste, odor and chlorine loads. Will impart a high “polish” to

the filtered water.

Taste/Odor/Color “G” Series Filters5

“U” Series Filters5

Activated Carbon

AC75

AC10

Granular / Black / Wide application for removal of organics

and some inorganics / Must be replaced on a regular basis

/ Life expectancy varies based on use

Sediment

Taste/Odor/Color

Chlorine/Iodine

“G” Series Filters

“U” Series Filters

Soft ‘N’ Filter w/ Mid-Vortech

Drinking Water Filters

Catalytic Carbon

CC75

CC10

Granular/Black / enhanced activated carbon that has

a higher catalytic power which produces an increased

electron transfer for better absorption.

Sulfur Removal

Chloramine

PROVECTR®

“G” Series Filters

City Soft

Filter Ag®

FA75

FA10

Granular / Off-White / Wide application for removal of

sediment / Life expectancy is unlimited Sediment “G” Series Filters

Soft ‘N’ Filter w/ Mid-Vortech

Filter Ag Plus

FP75

FP10

50 Light tan to white, 5 micron filtration Sediment “G” Series Filters

Birm®

BM75

BM10

Granular / Gray / Must not be used on waters with a pH

< 6.8 / Must have dissolved oxygen present at a level

of at least 15% of iron & manganese ppm / Max iron &

manganese level 10 ppm / Estimated life about 8-10 years

Sediment

Iron (clear & red)

Manganese (clear & red)

“G” Series Filters

Soft ‘N’ Filter w/ Mid-Vortech3

Greensand Plus

GP75

GP10

Granular / Black / Must not be used on waters with a pH

<6.8 / Must be regenerated with potassium permanganate

on a regular basis / Max iron & manganese level 10ppm/

Max H2S level 3ppm / Estimated life about 8-10 years

Sediment

Iron (clear & red)

Manganese (clear & red)

Hydrogen Sulfide

“GIP” Series Filters

“D” Gravel

DG20

DG50

Semi-Round / Brown / #20 Flint / Used as underbed for all

media in all filters providing for excellent flow distribution

in both service and backwash modes / Permanent unless

fouled but can be cleaned and re-used.

Underbed All Non Vortech Filter Systems

Installation Requirements

• A level floor position ahead of piping into water heater.

• Unit must be installed at least 10’ ahead of the inlet to a water heater to prevent damage due to

back-up of hot water.

• DO NOT install the unit in an area of direct sunlight or where freezing temperatures may occur!

(See Installation Diagrams for proper placement and plumbing connections.)

Filter Media Installation

Note:

• If household plumbing is galvanized and you intend to make the installation with copper (or vice versa), obtain

di-electric unions to prevent dissimilar metal corrosion.

• All plumbing lines not requiring “soft” water should be connected “upstream” of the softener, if installed. (See Typical

Installation Diagrams.)

Caution:

• If sweat soldering copper pipe (remember to always use lead free solder and flux), cover yoke and bypass valve with wet

rags to prevent heat damage to connections and control valve. If using PVC or plastic pipe, primers and solvent cements

specifically recommended for use with potable water are required.

Installation

Installation Procedure

- Water Supply Connection and Bypass Valve -

To allow for filter servicing, swimming pool filling or lawn sprinkling, a manual Bypass Valve has been installed at the

factory. The Bypass allows raw water to be manually routed around the filter.

1. Position filter at desired location for installation. If a water softener is to be installed, the filter should be positioned first

and then the softener. (See Installation Diagrams.)

2. The filter material is shipped separately from the mineral tank. The tank must be loaded with material after tank has

been placed at the desired location.

A. Remove the control valve by unscrewing from the tank. (Do not fill through dome hole, if installed.)

B. Use cap provided to place over top of distributor tube to prevent material from entering tube while filling.

C. Place media funnel (part # U-1006) in hole on top of tank.

D. Pour several gallons of water in the tank. (Fill tank about 1/3 full.)

E. Pour in the required filter media. No gravel is required. The required quantity of media is listed in the filter

specifications.

Note: If rebedding an existing unit and the system utilizes a standard tube & basket style distributor, a

“D” gravel underbedding will be required.

F. After filling the tank with material, use a garden hose or several buckets to fill the tank with water.

This will permit the filtering media to become soaked while preparing the installation and will prevent the control

valve from being plugged with floating material on initial backwash.

G. Remove funnel and clean filter media from tank threads.

H. Remove cap from distributor tube.

I. Replace control valve on mineral tank. Do not use Teflon tape or paste on valve threads, as the valve to

tank o-ring seals this joint.

Caution: Be extremely careful to position distributor tube into control valve distributor tube pilot hole.

3. Turn OFF main water supply and OPEN nearest faucet to relieve pressure.

4. Cut main line and install appropriate elbows and extensions.

Caution: Raised arrows located on the sides of control valve body and bypass valve indicate proper direction of water

flow. Install inlet and outlet piping in direction of arrows. It is recommended that a vacuum breaker be

installed on the inlet plumbing.

Installation Installation

Bypass - Shown

Electrical Connection -

1. Connect the power supply to the control valve and plug into a 115 volt / 60 Hz receptacle.

Note: Do not plug into an outlet controlled by a wall switch or pull chain that could inadvertently be turned off.

- Pressurizing The System -

2. Slowly rotate handle of the bypass valve to the SERVICE position.

3. Open the nearest faucet to evacuate air from plumbing lines.

4. Check for leaks! If water is observed leaking from bypass, o-rings on valve body may not be seated properly. Exercise

bypass valve.

5. After air is evacuated from plumbing lines, turn off faucet.

- Initial Control Valve Operation -

1. Advance control valve to BACKWASH (cycle 1) position and allow water to run to drain for 3 to 4 minutes.

Warning: Close handle on bypass prior to selecting the backwash position. After backwash position has been

established, slightly open valve on bypass to evacuate air from the media tank. Fully open bypass valve

when all air is depleted. This procedure will prevent media form being uplifted into control valve.

2. Advance control valve to RAPID RINSE (cycle 3) position and allow water to run to drain for 3 to 4 minutes.

3. Advance control valve to SERVICE (cycle 0) position.

Electronic Connections

P - Power Supply

B - Powered in Backwash Step Only (Cycle #1)

S - Powered in Entire Regeneration Cycle

Installation

P B S

- Drain Line Connection -

1. The drain line flow control assembly is pre-assembled for your convenience. Should you choose to hard plumb the

drain line, please remove the barb fitting. The flow control housing can be removed by removing the clip and pulling

straight out on housing.

Note: When re-installing the drain line flow control housing, be sure you hear and feel the O-Ring pop into place before

inserting the clip.

2. Install 1/2” I.D. drain line tubing (not included) from hose barb to an open drain. A 4” gap between end of the drain line

and the open drain is required to prevent waste water backflow. Keep the drain line as short as possible. An overhead

drain line can be used if necessary, but should discharge below the control valve. A syphon trap (taped loop) at the

outlet of the drain line is advisable to keep the drain line full and assure correct flow during backwash. Elbows or other

fittings must be kept at a bare minimum.

Note: Where the drain line is elevated above the control valve or exceeds 20 feet in length, 3/4” I.D. drain line tubing

should be used.

Main Menu

12:00

1. To enter Main Menu, press the Menu/Enter button.

(Time of Day will flash)

2. To set the Time of Day, press the Set/Change button.

(First digit will flash) Example (12:00) -

To change digit value, press the Set/Change button.

- To accept the digit value, press the Menu/Enter button.

- Next digit will flash to begin setting.

- Once the last digit display is accepted, all digits will flash.

3. To set A.M. or P.M., press the Menu/Enter button.

- To change digit value, press the Set/Change button. Example ( A )

- To accept the digit value, press the Menu/Enter button.

- Once A.M. or P.M. is accepted, the next menu item will flash.

4. a. To set the Number of Days between Backwash Cycles (A), press the Set/Change button. -

Repeat instructions from step (2). Example ( A - 06 )

Notes: 1) Maximum value is 29.

2) If value set to 0, Automatic Backwash will never occur.

3) Default setting is 6 days for filters.

5. To Exit Main Menu, press the Menu/Enter button.

Note: If no buttons are pressed for 60 seconds, the Main Menu will be exited automatically.

Programming the Control Valve

Installation

- Final Checkout -

1. Be certain that the bypass valve is in Service position and main valve is completely on.

2. Check electrical supply to be certain the cord is connected to an uninterrupted 115 volt outlet.

3. REGISTER YOUR PRODUCT at www.watersoftinc.com

4. Leave this manual with the homeowner.

Important Notice - The plumbing system, piping, pressure tank, hot water tanks, softeners, etc. that have been exposed

to iron bearing water may need to be cleaned of the precipitated iron that has been collected in them or iron bleed thru

may be a problem. We suggest all tanks be drained and flushed thoroughly.

- Programming The Control Valve -

1. Set time of day.

2. Set a.m. or p.m.

3. Set number of days between backwash. (This generally will be every 4 to 6 days.)

1. Set regeneration time if other than 12:00 a.m. is desired.

Normal Operation

1. Home Display

a. Alternates between the display of Time of Day and Number of Days until the Next Backwash.

(Metered Softeners will alternate between time of days and gallons remaining until next regeneration)

- Days Remaining until the Next Backwash will count down from the entered value until it reaches

1 day remaining.

- A Backwash Cycle will then be initiated at the next designated regeneration time.

2. Battery Back-Up (Uses a standard 9-volt alkaline battery.)

Features of Battery Back-Up:

• During power failures, the battery will maintain the time of day as long as the battery has power.

The display is turned off to conserve battery power during this time. To confirm that the battery

is working, press either button and the display will turn on for five (5) seconds.

• If power failure occurs while system is regenerating, the Isobar 2 will motor to a shut off position

to prevent constant flow to drain. Depending upon system pressure and other factors, it is

possible to observe a reduced flow to drain during this step. After power is restored, the Isobar

2 will return and finish the cycle where it left off prior to the power interruption.

• When used without battery back-up, during a power failure, the unit stops at its current point in

the regeneration position and then restarts at that point when the power is restored. The time

will be offset by the increment of time the unit was without power, so it is necessary to reset the

time of day on the unit. No other system will be affected.

Programming the Control Valve

Filters Default (Min)

Step 1 Backwash 10

Step 2 Rest 5

Step 3 Rapid Rinse 10

Step 4 Not Used 0

Starting Extra Regeneration Cycle

1. To Start Delayed Extra Cycle Example ( 1) - If Days

Remaining Until Next Backwash does not read ‘1’, press and hold the Set/Change button for 3 seconds

until the display reads ‘1’.

- Backwash cycle will initiate at the next designated backwash time.

2. To start Immediate Extra Cycle First complete above step.

- With Days Remaining Until Next Regeneration at ‘1’.

- Press and hold the Set/Change button.

- After 3 seconds, the backwash cycle will begin.

3. To Fast Cycle thru regeneration First complete above 2 steps.

Note:Press and hold the Set/Change button for 3 seconds to advance to the next cycle step.

Fast Cycle is not necessary unless desired to manually step through each cycle step.

(Repeat until valve returns to the home display)

Altri manuali per ISOBAR II

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Water Soft Unità di controllo

Water Soft

Water Soft ISOBAR II Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente