Weber Flame iQ Manuale utente

WWW.WEBER.COM 1

OWNER’S GUIDE

FOR USE WITH UNIVERSAL LIQUEFIED PETROLEUM GAS (ULPG / LPG) ONLY

SUITABLE FOR THE BABY Q SERIES - Q1000 AND Q1200 MODELS ONLY

SCAN FOR ASSEMBLY

AND HOW TO USE

INSTRUCTIONS

Thank you for purchasing the WEBER Flame iQ Accessory for your WEBER Baby Q.

Take a few minutes to read the manual.

Congratulations on the purchase of your WEBER Flame iQ

with patented technology.

The Flame iQ requires a 12 V or 240 V power supply. The

Flame iQ comes with a 2.4 metre 12 V power cable and a

1 metre 240/12 V power cable. This electrical connection

provides the Flame iQ with the ability to continually sense for

a flame.

WHAT IS THE WEBER Flame iQ?

The Flame iQ is a type of flame safeguard device, with added

features and benefits.

A flame safeguard device is designed to stop the flow of gas

to an appliance in the case that the gas flame goes out – for

example, if the flame is blown out in windy conditions.

The Flame iQ has the added functionality of continuously

sensing for a flame. It will attempt to reignite the burner in

the event of a ‘flame out’ (up to 3 attempts), before shutting

off the gas and going into a lockout mode. If the burner

reignites, the Flame iQ will reset for another 3 attempts.

HOW DOES THE WEBER Flame IQ WORK?

The Flame iQ features a sensing probe, situated on the

burner. If the probe senses a ‘flame out’, it sends a signal to

the Flame iQ, which then attempts to reignite the burner, up

to 3 times at 5 second intervals.

If the burner is not reignited by the third relighting attempt,

it will shut off the gas to the burner and go into lockout

mode. This is shown on the Flame iQ when the reset light is

illuminated (refer to lighting instructions on page 7).

If the burner is successfully reignited on the first, second or

third attempt, the Flame iQ resets itself (and will attempt 3

reignitions if the probe again senses a ‘flame out’).

ADDITIONAL BENEFITS OF USING THE WEBER Flame iQ

WITH YOUR WEBER Baby Q

• The Flame iQ meets the requirements of the Australian

& New Zealand Standard for Outdoor Gas Appliances

for barbecues connected to the piping on a caravan or

boat. Once your Baby Q is fitted with a Flame iQ, it can

be connected to the plumbed gas supply of a boat or

caravan.

• Should the flame in your Baby Q blow out due to strong

winds, the Flame iQ will sense a ‘flame out’ and attempt

to re-ignite the burner. This will be seamless and happen

continuously whenever the flame is blown out (if the

burner is reignited within 3 attempts at each ‘flame out’).

Your food will still be cooked through perfectly.

• When the Flame iQ is turned on, it runs a self-check to

ensure that there is no flame present on the burner. If

there is a flame present the Flame iQ will go into reset

mode. This ensures that the Flame iQ is in the correct

safe start position with no gas flowing through the Flame

iQ.

• Easy-to-see indicator lights on the Flame iQ control

panel mean you don’t have to lift the lid of your barbecue

to see if it’s alight.

The lights indicate:

a) Green light illuminated - Flame iQ is ready to operate.

b) Blue light illuminated - flame detected at burner.

c) Blue light off - flame out detected and reignition being

attempted.

d) Red light illuminated - lockout mode due to

unsuccessful reignition.

• A pre-set maximum run time of 8 hours is built into the

Flame iQ, meaning that if you forget to turn your Baby Q

off after use, it will automatically cut the gas supply to

the barbecue after 8 hours of continuous run time.

WWW.WEBER.COM 2

DANGER DANGER

Failure to follow the DANGERS, WARNINGS

and CAUTIONS contained in this Owner’s

Guide may result in serious bodily injury

or death, or may result in a fire or an

explosion causing damage to property.

For additional information please refer to

the WEBER barbecue owner’s guide for the

Q1000 and Q1200.

The Flame iQ needs to be plugged into a

12 V or 240 V power supply.

DANGERS

WARNINGS

THIS GAS ACCESSORY IS DESIGNED

FOR OUTDOOR USE ONLY.

DANGER

Shut off gas to the appliance.

Extinguish any open flames.

Open lid.

If odour continues, keep away from

the appliance and immediately

call your gas supplier or your fire

department.

Failure to follow these instructions could

result in fire or explosion which could

cause property damage, personal injury

or death.

If you smell gas:

Never operate the Baby Q with Flame

iQ unattended.

Never operate Baby Q with Flame iQ

within 610 mm (2 ft) of any structure,

combustible material or other gas

cylinder.

Never operate Baby Q with Flame iQ

within 7.5 m (25 ft) of any flammable

liquid.

If a fire should occur, turn off your gas

bottle, keep away and immediately call

your fire department. Do not attempt

to extinguish an oil or grease fire with

water.

Failure to follow these instructions could

result in fire, explosion or burn hazard,

which could cause property damage,

personal injury or death.

This instruction manual contains important information necessary for the proper assembly and safe use of the Weber

Flame iQ. Read and follow all warnings and instructions before tting and using the Flame iQ accessory. Keep this manual

for future reference. Carefully follow all leak-check procedures in this Owner’s Guide. Do not use the Flame iQ without

rst reading the burner ignition sections in this manual.

Do not use the WEBER Flame iQ unless

all parts are in place. The accessory

must be properly assembled according

to the assembly instructions.

Your WEBER Flame iQ should never be

used by children. Accessible parts of

the accessory may be very hot. Keep

young children and pets away while

accessory is in use.

This WEBER Flame iQ is not intended

for commercial use.

Do not attempt to disconnect the gas

regulator and hose assembly or any

gas tting while your Flame iQ is in

operation.

Use heat-resistant barbecue mitts or

gloves, whilst cooking on the barbecue.

After a period of storage and/or

nonuse, the WEBER Flame iQ should be

checked for gas leaks. See instructions

in this Owner’s Guide for correct

procedures.

Do not operate the WEBER Flame iQ if

there is a gas leak present.

Do not use a ame to check for gas

leaks.

Universal liqueed petroleum gas

(ULPG / LPG) is not natural gas. The

conversion or attempted use of natural

gas in a universal liqueed petroleum

gas unit or universal liqueed

petroleum gas in a natural gas unit is

dangerous and will void your warranty.

Keep any electrical supply cord and the

fuel supply hose away from any heated

surfaces.

The Flame iQ should be cleaned on a

regular basis.

If you see, smell or hear the hiss of

gas escaping from the rellable LPG

cylinder:

1. Move away from rellable LPG

cylinder.

2. Do not attempt to correct the

problem yourself.

3. Call your re department.

A dented or rusty LPG cylinder may be

hazardous and should be checked by

your LPG supplier. Do not use a LPG

cylinder with a damaged valve.

Although your LPG cylinder may

appear to be empty, gas may still be

present, and the LPG cylinder should

be transported and stored accordingly.

The use of alcohol, prescription drugs,

non-prescription drugs, or illegal

drugs may impair the consumer’s

ability to properly and safely assemble,

move, store or operate the WEBER

Flame iQ.

WWW.WEBER.COM 3

TABLE OF CONTENTS

DANGERS & WARNINGS........................... 2

WARRANTY.............................................. 3

PARTS LIST.............................................. 4

ASSEMBLY............................................. 4-5

LEAK CHECK............................................ 6

BURNER IGNITION & USAGE..................... 7

TROUBLESHOOTING................................. 8

The accessory illustrated in this Owner’s Guide may vary

slightly from the model purchased.

WARRANTY

PRODUCT WARRANTY PERIOD

DISCLAIMERS

WEBER MAKES NO IMPLIED WARRANTIES INCLUDING WITHOUT

LIMITATION ANY IMPLIED WARRANTY OF MERCHANTABILITY OR

FITNESS FOR A PARTICULAR PURPOSE, OTHER THAN WHAT IS

EXPRESSLY MADE IN THIS LIMITED WARRANTY. NO WARRANTIES

SHALL APPLY AFTER THE APPLICABLE PERIODS OF THIS LIMITED

WARRANTY. NO OTHER WARRANTIES GIVEN BY ANY PERSON OR

ENTITY, INCLUDING A DEALER OR RETAILER WITH RESPECT

TO ANY PRODUCT (SUCH AS ANY “EXTENDED WARRANTIES”),

SHALL BIND WEBER. THE EXCLUSIVE REMEDY OF THIS LIMITED

WARRANTY IS REPAIR OR REPLACEMENT OF THE PART OR

PRODUCT. THE TERMS OF THIS LIMITED WARRANTY PROVIDE

THE SOLE AND EXCLUSIVE REMEDY ARISING FROM THE SALE OF

THE PRODUCTS COVERED HEREBY. WEBER SHALL NOT BE LIABLE

FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL

LOSS OR DAMAGES. SOME JURISDICTIONS DO NOT ALLOW THE

EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL

DAMAGES, OR LIMITATIONS ON HOW LONG AN IMPLIED

WARRANTY LASTS, SO THE ABOVE EXCLUSIONS OR LIMITATIONS

MAY NOT APPLY TO YOU.

IN NO EVENT SHALL RECOVERY OF ANY KIND BE GREATER THAN

THE AMOUNT OF THE PURCHASE PRICE OF THE WEBER PRODUCT

SOLD.

YOU ASSUME THE RISK AND LIABILITY FOR LOSS, DAMAGE, OR

INJURY TO YOU AND YOUR PROPERTY AND/OR TO OTHERS AND

THEIR PROPERTY ARISING OUT OF THE MISUSE OR ABUSE OF THE

PRODUCT OR FAILURE TO FOLLOW INSTRUCTIONS PROVIDED BY

WEBER IN THE ACCOMPANYING OWNER’S GUIDE.

THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS,

AND YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY IN

DIFFERENT JURISDICTIONS.

PARTS AND ACCESSORIES REPLACED UNDER THIS LIMITED

WARRANTY ARE WARRANTED ONLY FOR THE BALANCE OF THE

ORIGINAL WARRANTY PERIOD(S).

THIS LIMITED WARRANTY APPLIES TO PRIVATE SINGLE FAMILY

HOME OR APARTMENT USE ONLY AND DOES NOT APPLY TO

WEBER BARBECUES USED IN COMMERCIAL, COMMUNAL OR

MULTI-UNIT SETTINGS SUCH AS RESTAURANTS, HOTELS,

RESORTS OR RENTAL PROPERTIES.

WEBER MAY FROM TIME TO TIME CHANGE THE DESIGN OF ITS

PRODUCTS. NOTHING CONTAINED IN THIS LIMITED WARRANTY

SHALL BE CONSTRUED AS OBLIGATING WEBER TO INCORPORATE

SUCH DESIGN CHANGES INTO PREVIOUSLY MANUFACTURED

PRODUCTS, NOR SHALL SUCH CHANGES BE CONSTRUED AS AN

ADMISSION THAT PREVIOUS DESIGNS WERE DEFECTIVE.

WEBER’S RESPONSIBILITIES

WEBER provides, to the original purchaser of the WEBER product (or

in the case of a gift or promotional situation, the person for whom

it was purchased as a gift or promotional item), that the WEBER

product is free from defects in material and workmanship for the

period(s) of time specied below when assembled and operated

in accordance with the accompanying Owner’s Guide. (Note: If you

lose or misplace your WEBER Owner’s Guide, a replacement is

available online at www.weber.com). Under normal, private single

family home or apartment use and maintenance, WEBER agrees to

repair or replace defective parts within the applicable time periods,

limitations and exclusions listed below. THIS LIMITED WARRANTY

IS EXTENDED ONLY TO THE ORIGINAL PURCHASER AND IS NOT

TRANSFERABLE TO SUBSEQUENT OWNERS, EXCEPT IN THE CASE

OF GIFTS AND PROMOTIONAL ITEMS AS NOTED ABOVE.

Our goods come with guarantees that cannot be excluded under

the Australian Consumer Law. You are entitled to a replacement

or refund for a major failure and for compensation for any other

reasonably foreseeable loss or damage. You are also entitled

to have the goods repaired or replaced if the goods fail to be of

acceptable quality and the failure does not amount to a major

failure.

The benets given under this Limited Warranty are in addition to

other rights and remedies you have under the Australian Consumer

Law in relation to this WEBER gas barbecue.

OWNER’S RESPONSIBILITIES

To ensure trouble-free warranty coverage, please retain your

original sales receipt and/or invoice.

The Owner must take reasonable care of the WEBER product

and follow all assembly instructions, usage instructions and

preventative maintenance as outlined in the accompanying

Owner’s Guide. If you live in a coastal area, or have your

product located near a pool, maintenance includes regular

washing and rinsing of the exterior surfaces. If you believe

that you have a part that is covered by this Limited Warranty,

please contact the WEBER Customer Service Representative

in your area using the contact information on our web site.

WEBER will, upon investigation, repair or replace (at its option)

a defective part covered by this Limited Warranty. In the event

that repair or replacement are not possible, WEBER may chose

(at its option) to replace the accessory in question with a new

accessory of equal or greater value. WEBER may ask you to

return parts for inspection, shipping charges to be pre-paid.

This LIMITED WARRANTY does not cover damage, deterioration,

discoloration and/or rust caused by:

• Abuse, misuse, alteration, modification, misapplication,

vandalism, neglect, improper assembly or installation,

and failure to properly perform normal and routine

maintenance;

• Insects (such as spiders) and rodents (such as squirrels),

including but not limited to damage to burner tubes and/

or gas hoses;

• Exposure to salt air and/or chlorine sources such as

swimming pools and hot tubs/spas;

• Severe weather conditions such as hail, hurricanes,

earthquakes, tsunamis or surges, tornadoes or severe

storms.

The use and/or installation of parts on your WEBER product

that are not genuine WEBER parts will void this Limited

Warranty, and any damages that result are not covered by this

Limited Warranty.

Any conversion of a gas barbecue not authorized by WEBER and

performed by a WEBER authorized service technician will void

this Limited Warranty.

Weber-Stephen Products (Aust) Pty Ltd.

Level 1, 142-144 Fullarton Road

Rose Park, SA 5067 AUSTRALIA

1300 301 290 (toll free)

Weber-Stephen Products New Zealand.

86 East Highbrook Drive

East Tamaki, Auckland 2013 NEW ZEALAND

0800 493 237 (toll free)

Flame iQ: 3 years

Thank you for purchasing a WEBER product.

Weber-Stephen Products (Aust) Pty Ltd and

Weber-Stephen Products New Zealand (“WEBER”)

prides themselves on delivering a safe, durable and

reliable product.

This is WEBER’s Limited Warranty provided to you

at no extra charge. It contains the information you

will need to have your WEBER product repaired in

the unlikely event of a failure or defect.

WWW.WEBER.COM 4

PARTS LIST & ASSEMBLY

1. Prior to commencement of fitting the

Flame iQ to your barbecue, ensure the

barbecue is clean of any cooking debris

(existing barbecue). If recently used,

ensure the barbecue has cooled before

attempting to fit the Flame iQ.

2. Ensure the gas cylinder is not connected

to the barbecue. If connected, disconnect

the hose/regulator assembly from the LPG

cylinder.

3. Disconnect the hose and regulator

assembly from the barbecue. Using the

supplied 5/8” and 3/4” spanners, unscrew

the hose fitting from the manifold inlet

fitting. Be careful not to damage the

connections.

INSTRUCTIONS APPLICABLE TO MODELS Q1000, Q1200

PARTS LIST

4. Remove the barbecue lid by removing the

hinge pins and clips.

5. Remove the barbecue grills to enable

access to the burner.

KEEP THIS SPANNER

STATIONARY

6. Remove the hose guide/retaining ring

from the rear frame leg. Lay the barbecue

on it’s back for ease of access and remove

the mounting screws using the supplied

1/4” spanner. Be careful to retain the

screws as these are required to remount

the Flame iQ. The hose guide/retaining

ring is not reused and can be recycled.

7. Mount the Flame iQ attachment bracket

in position, using the supplied 1/4”

spanner. Use the screws and mounting

points previously used for the hose guide/

retaining ring.

8. Sit the barbecue back on its feet. Remove

the screw securing the burner using a

flat head screwdriver. Rotate the burner

tube towards you into a vertical position

and slide to the left to disengage from the

manifold/valve.

9. Place the Flame iQ underneath the handle

and behind the manifold/valve (ensure

the Flame iQ is on the outside of the

attachment bracket). Loosely connect by

hand tightening the outlet gas connection

on the Flame iQ to the manifold inlet

fitting. Do not over-tighten.

1. Flame iQ control box

2. Attachment bracket

3. Flame iQ 12 V 2.4 metre

power cable

4. 240/12 V power socket

& 1.0 metre cable.

5. 2 x screws [M4 8mm]

7. Safeguard sticker

1 x Phillips Head Screwdriver

1 x Flat Head Screwdriver

INCLUDED with your Flame iQ:

NOT INCLUDED:

6. Spanners

1/4” 3/4” and 5/8” 3/4”

WWW.WEBER.COM 5

10. Secure the Flame iQ to the attachment

bracket with the 2 screws using a phillips

head screwdriver.

11. Feed the sensor probe through the

burner clearance hole in the side of the

barbecue cook box. Pass the sensor front

legs through first, then swing the sensor

through the clearance hole

ASSEMBLY

INSTRUCTIONS APPLICABLE TO MODELS Q1000, Q1200

12. Reinstall the burner to where it is in a vertical

position, but not attached to the manifold/

valve.

13. Clip the sensor probe into position on the

burner. Ensure the sensor probe clips into

position on the burner by hooking under

the front leg over the flat section of the

burner tube (1) and then push the back

legs down onto the burner tube (2).

14. Slide the burner tube to the right over the

manifold/valve ensuring that the wires are

not pinched or twisted around the burner

tube. Rotate the burner tube back to a

horizontal plane ensuring it is locked onto

the manifold/valve and refit the burner

tube with securing screw.

15. Screw the hose and regulator assembly

to the inlet of the Flame iQ using the 3/4”

spanners. Ensure you only tighten the

nut on the hose. Do not tighten the nut on

the Flame iQ housing. Reconnect the gas

cylinder.

16. Using the 5/8” and 3/4” spanners

provided, tighten the outlet gas

connection on the Flame iQ to the

manifold/valve inlet fitting (previously

finger tightened in step 9).

17. Open the power supply weather cover.

Connect the power cable.

18. Place the ‘Flame safeguard fitted’ label

on the data label to be found on the back

leg of the barbecue. Do not obscure the

serial number.

19. Conduct a leak check of all gas fittings,

including with the Flame iQ powered

up and activated (on – green light

illuminated) but barbecue gas control

knob off. Refer to page 6 to perform a

leak test.

WARNING: needs to be plugged into a 12 V or 240 V

power supply.

20. If no leaks are detected, refer to Flame

iQ operating instructions and check

functionality of Flame iQ.

21. After checking operation, refit cooking

grills and lid. Your barbecue is now

ready to use, incorporating the Flame iQ.

KEEP THIS SPANNER

STATIONARY

KEEP THIS

SPANNER

STATIONARY

WWW.WEBER.COM 6

PREPARING TO USE YOUR Flame iQ

WHAT IS A LEAK CHECK?

The fuel system in your WEBER

barbecue fitted with Flame iQ

features connections and fittings. A

leak check is a reliable way to make

sure that no gas is escaping from any

of the connections or fittings.

Although all factory-made

connections have been thoroughly

checked for gas leaks, it’s important

to perform a leak check before using

your Flame iQ for the first time, as

well as anytime you disconnect and

reconnect a fitting and each time you

perform routine maintenance.

NOTE: All factory-made connections have been

thoroughly checked for gas leaks and the burner has

been ame-tested. As a safety precaution, however,

you should check all ttings for leaks before using

your WEBER gas barbecue. Shipping and handling may

loosen or damage a gas tting.

You will need: A spray bottle, brush or rag and a soap

and water solution. (You can make your own soap and

water solution by mixing 20% liquid soap with 80%

water; or, you can usually nd leak check solution in the

plumbing section of a hardware store.)

When leak checking is complete, turn gas supply off

at the source and rinse connections with water.

a) Regulator-to-LPG cylinder connection (4).

b) Regulator hose-to-regulator connection (5).

c) Flame iQ to regulator hose connection (6).

d) Flame iQ to valve connection (7).

Make sure the burner control knob is turned off by

pushing it in and turning it clockwise to the OFF (O)

position (1).

Turn gas supply on at source (2).B)

Plug Flame iQ to power source (3A) and press the

ON button (3B).

To check for leaks, wet ttings with the soap and

water solution, using a spray bottle, brush or rag. If

bubbles form, or if a bubble grows, there is a leak.

Apply the soap and water solution to the following

connections:

NOTE: Since some leak test solutions, including soap and water, may be

slightly corrosive, all connections should be rinsed with water after checking

for leaks.

WARNING: The gas connections of your gas

barbecue have been factory tested. We do,

however, recommend that you leak check

all gas connections before operating your

gas barbecue.

WARNING: Perform these leak checks

even if your barbecue was dealer or store

assembled.

WARNING: You should check for gas leaks

every time you disconnect and reconnect a

gas tting.

WARNING: Do not ignite burner when leak checking.

WARNING: If there is a leak at connection (4,5,6 or 7)

turn off the gas. DO NOT OPERATE THE BARBECUE.

Contact the Customer Service Representative in

your area using the contact information on our

website. Log onto www.weber.com.

Sparks or open ames will result in a re or

explosion, which can cause serious bodily injury

or death and damage to property.

CHECKING FOR GAS LEAKS

WWW.WEBER.COM 7

16 WWW.WEBER.COM

BURNER IGNITION & USAGE

Summary lighting instructions are on the

instruction tag (Q 1000, Q 1200) or the right

fold-out table (Q 2000, Q2200).

METHODS OF BURNER

IGNITION

There are two ways to ignite

the burner. The ﬁrst is by using

the ignition system built into

your barbecue. The second is

with a match.

Next are the steps for

igniting your barbecue using

the ignition system. On the

following page are steps for

igniting your barbecue with a

match.

BURNER IGNITION

A) Open the barbecue lid (1).

m DANGER

Failure to open the lid before igniting the

barbecue’s burner, or not waiting ﬁve

minutes to allow the gas to clear if the

barbecue does not light, may result in an

explosive ﬂare-up which can cause serious

bodily injury or death.

B) Unfold the side tables(2) (Q 2000™, Q 2200™).

C) Make sure the burner control knob is turned to the o

() position(3). Check by pushing burner control knob

in and turning it clockwise until it stops.

D) Turn gas supply on at source.

E) Push burner control knob in and turn it

counterclockwise to start/high ( ) position (4).

F1) Push the red igniter button several times, so it clicks

each time (5) (Q 1000™, Q 2000™).

F2) Push and hold in the electronic igniter button (6)

(Q 1200™, Q 2200™). You will hear the igniter clicking.

G) Check that the burner is lit by looking through the

cooking grills. You should see a ﬂame.

m WARNING: Do not lean over the open

barbecue while igniting.

m WARNING: If burner fails to ignite within

ﬁve seconds, stop, turn the burner control

knob to o and wait ﬁve minutes to allow

the gas to clear before you try again or

light with a match.

TO EXTINGUISH BURNER

Push burner control knob in and turn it clockwise to the o

() position.

m CAUTION: Do not fold in side tables until

barbecue is cold (Q 2000, Q 2200).

Some batteries have a plastic

protective wrap around them.

This plastic must be removed

before you attempt to ignite

your barbecue. Do not confuse

this plastic with the battery

label.

model lighting

instructions

document

use these illustrations

if work

BURNER IGNITION & USAGE

A) Open the barbecue lid (1) and unfold sidetables if

applicable (2).

BURNER IGNITION - Getting started

BURNER IGNITION - Ignition system BURNER IGNITION - Lighting with a match

Depress the RESET button (illuminated red) continuously

for ve (5) seconds to reset the Flame iQ (red light will go

out). Repeat the ignition steps as above.

RESETTING THE Flame iQ AFTER FLAME

FAILURE AND LOCKOUT

TO EXTINGUISH BURNER

Push burner control knob in and turn it clockwise to

the OFF (O) position. Depress the ON/OFF button on the

Flame iQ control box to switch off the Flame iQ.

F) Strike a match and put the ame under the matchlight

hole (5). While holding the lit match, push burner control

knob in and turn it counter clockwise to start/high ( )

position (6).

16 WWW.WEBER.COM

BURNER IGNITION & USAGE

Summary lighting instructions are on the

instruction tag(Q 1000, Q 1200) or the right

METHODS OF BURNER

IGNITION

There are two ways to ignite

the burner. The ﬁrst is by using

the ignition system built into

your barbecue. The second is

with a match.

Next are the steps for

igniting your barbecue using

the ignition system. On the

following page are steps for

igniting your barbecue with a

match.

BURNER IGNITION

A) Open the barbecue lid (1).

mDANGER

Failure to open the lidbeforeigniting the

barbecue’sburner, or not waiting ﬁve

minutes to allow the gas to clear if the

barbecue does not light, may result in an

explosive ﬂare-up which can cause serious

bodily injury or death.

B) (2) (Q 2000 ™,Q 2200™).

C) Make sure the burner control knob is turned to t

((3) . Check by pushing burner control knob

in and turning it clockwise until it stops.

D) Turn gas supply on at source.

E) Push burner control knob in and turn it

counterclockwise to start/high ( ) position (4) .

F1) Push the red igniter button several times, so it clicks

each time (5) (Q 1000 ™, Q 2000 ™).

F2) Push and hold in the electronic igniter button (6)

(Q 1200 ™, Q 2200 ™). You will hear the igniter clicking.

G) Check that the burner is lit by looking through the

cooking grills . You should see a ﬂame.

mWARNING: Do not lean over the open

barbecue while igniting.

mWARNING: If burner fails to ignite within

ﬁve seconds, stop, turn the burner control

the gas to clear before you try again or

light with a match.

TO EXTINGUISH BURNER

( ) position.

mCAUTION: Do not fold in side tables until

barbecue is cold (Q 2000, Q 2200).

Some batteries have a plastic

protective wrap around them.

This plastic must be removed

before you attempt to ignite

your barbecue . Do not confuse

this plastic with the battery

label.

model lighting

instructions

document

use these illustrations

if work

16 WWW.WEBER.COM

BURNER IGNITION & USAGE

Summary lighting instructions are on the

instruction tag(Q 1000, Q 1200) or the right

METHODS OF BURNER

IGNITION

There are two ways to ignite

the burner. The ﬁrst is by using

the ignition system built into

your barbecue. The second is

with a match.

Next are the steps for

igniting your barbecue using

the ignition system. On the

following page are steps for

igniting your barbecue with a

match.

BURNER IGNITION

A) Open the barbecue lid (1).

mDANGER

Failure to open the lidbeforeigniting the

barbecue’sburner, or not waiting ﬁve

minutes to allow the gas to clear if the

barbecue does not light, may result in an

explosive ﬂare-up which can cause serious

bodily injury or death.

B) (2) (Q 2000 ™,Q 2200™).

C) Make sure the burner control knob is turned to t

((3) . Check by pushing burner control knob

in and turning it clockwise until it stops.

D) Turn gas supply on at source.

E) Push burner control knob in and turn it

counterclockwise to start/high ( ) position (4).

F1) Push the red igniter button several times, so it clicks

each time (5) (Q 1000 ™, Q 2000 ™).

F2) Push and hold in the electronic igniter button (6)

(Q 1200 ™, Q 2200 ™). You will hear the igniter clicking.

G) Check that the burner is lit by looking through the

cooking grills . You should see a ﬂame.

mWARNING: Do not lean over the open

barbecue while igniting.

mWARNING: If burner fails to ignite within

ﬁve seconds, stop, turn the burner control

the gas to clear before you try again or

light with a match.

TO EXTINGUISH BURNER

( ) position.

mCAUTION: Do not fold in side tables until

barbecue is cold (Q 2000, Q 2200).

Some batteries have a plastic

protective wrap around them.

This plastic must be removed

before you attempt to ignite

your barbecue . Do not confuse

this plastic with the battery

label.

model lighting

instructions

document

use these illustrations

if work

16 WWW.WEBER.COM

BURNER IGNITION & USAGE

Summary lighting instructions are on the

instruction tag (Q 1000, Q 1200) or the right

fold-out table (Q 2000, Q2200).

METHODS OF BURNER

IGNITION

There are two ways to ignite

the burner. The ﬁrst is by using

the ignition system built into

your barbecue. The second is

with a match.

Next are the steps for

igniting your barbecue using

the ignition system. On the

following page are steps for

igniting your barbecue with a

match.

BURNER IGNITION

A) Open the barbecue lid (1).

m DANGER

Failure to open the lid before igniting the

barbecue’s burner, or not waiting ﬁve

minutes to allow the gas to clear if the

barbecue does not light, may result in an

explosive ﬂare-up which can cause serious

bodily injury or death.

B) Unfold the side tables(2) (Q 2000™, Q 2200™).

C) Make sure the burner control knob is turned to the o

() position(3). Check by pushing burner control knob

in and turning it clockwise until it stops.

D) Turn gas supply on at source.

E) Push burner control knob in and turn it

counterclockwise to start/high ( ) position (4).

F1) Push the red igniter button several times, so it clicks

each time (5) (Q 1000™, Q 2000™).

F2) Push and hold in the electronic igniter button (6)

(Q 1200™, Q 2200™). You will hear the igniter clicking.

G) Check that the burner is lit by looking through the

cooking grills. You should see a ﬂame.

m WARNING: Do not lean over the open

barbecue while igniting.

m WARNING: If burner fails to ignite within

ﬁve seconds, stop, turn the burner control

knob to o and wait ﬁve minutes to allow

the gas to clear before you try again or

light with a match.

TO EXTINGUISH BURNER

Push burner control knob in and turn it clockwise to the o

( ) position.

m CAUTION: Do not fold in side tables until

barbecue is cold (Q 2000, Q 2200).

Some batteries have a plastic

protective wrap around them.

This plastic must be removed

before you attempt to ignite

your barbecue. Do not confuse

this plastic with the battery

label.

model lighting

instructions

document

use these illustrations

if work

WWW.WEBER.COM 17

BURNER IGNITION & USAGE

BURNER IGNITION –

Lighting with a Match

A) Open the barbecue lid (1).

m DANGER

Failure to open the lid before igniting the

barbecue’s burner, or not waiting ﬁve

minutes to allow the gas to clear if the

barbecue does not light, may result in an

explosive ﬂare-up which can cause serious

bodily injury or death.

B) Unfold the side tables(2) (Q 2000™, Q 2200™).

C) Make sure the burner control knob is turned to the o

() position(3). Check by pushing burner control knob

in and turning it clockwise until it stops.

D) Turn gas supply on at source.

E) Strike a match and put the ﬂame under the matchlight

hole (4). While holding lit match, push burner control

knob in and turn it counterclockwise to start/high ( )

position (5).

F) Check that the burner is lit by looking through the

cooking grills (6). You should see a ﬂame.

m WARNING: Do not lean over the open

barbecue while igniting. Keep your face

and body at least 30 cm (12 in) away

from the matchlight hole when lighting

thebarbecue.

m WARNING: If the burner fails to ignite

within ﬁve seconds, stop, turn the burner

control knob to o and wait ﬁve minutes

to allow the gas to clear before you try

again.

TO EXTINGUISH BURNER

Push burner control knob in and turn it clockwise to the o

() position.

m CAUTION: Do not fold in side tables until

barbecue is cold (Q 2000, Q 2200).

WWW.WEBER.COM 17

BURNER IGNITION & USAGE

BURNER IGNITION –

Lighting with a Match

A) Open the barbecue lid (1).

m DANGER

Failure to open the lid before igniting the

barbecue’s burner, or not waiting ﬁve

minutes to allow the gas to clear if the

barbecue does not light, may result in an

explosive ﬂare-up which can cause serious

bodily injury or death.

B) Unfold the side tables(2) (Q 2000™, Q 2200™).

C) Make sure the burner control knob is turned to the o

() position(3). Check by pushing burner control knob

in and turning it clockwise until it stops.

D) Turn gas supply on at source.

E) Strike a match and put the ﬂame under the matchlight

hole (4). While holding lit match, push burner control

knob in and turn it counterclockwise to start/high ( )

position (5).

F) Check that the burner is lit by looking through the

cooking grills (6). You should see a ﬂame.

m WARNING: Do not lean over the open

barbecue while igniting. Keep your face

and body at least 30 cm (12 in) away

from the matchlight hole when lighting

thebarbecue.

m WARNING: If the burner fails to ignite

within ﬁve seconds, stop, turn the burner

control knob to o and wait ﬁve minutes

to allow the gas to clear before you try

again.

TO EXTINGUISH BURNER

Push burner control knob in and turn it clockwise to the o

() position.

m CAUTION: Do not fold in side tables until

barbecue is cold (Q 2000, Q 2200).

DANGER: Failure to open the lid before igniting the

barbecue’s burner, or not waiting ve minutes to

allow the gas to clear if the barbecue does not light,

may result in an explosive are-up which can cause

serious bodily injury or death.

B) Make sure the burner control knob is turned to the OFF

(O) position (3). Check by pushing burner control knob in

and turning it clockwise until it stops.

C) Ensure that the Flame iQ has power (either by way of

12 V or 240 V) and the power supply is switched on.

D) Turn gas supply on at source.

E) Depress the ON/OFF button on the Flame iQ control

box– the button will illuminate green (4).

Note: You have 30 seconds to ignite the barbecue from

when you press the Flame iQ ON button. Should the

barbecue not ignite within the 30 seconds the Flame iQ

will go into lockout and need to be reset.

F) Push the burner control knob in and turn it counter

clockwise to start/high ( ) position (5).

G1) Push the red igniter button several times, so it clicks

each time (6) (Q1000)

G2) Push and hold in the electronic igniter button ( ) (7)

(Q1200). You will hear the igniter clicking.

OR,

H) Once ame is detected, the blue light on the Flame iQ

control box illuminates (8).

I) After ignition close the barbecue lid to enable

pre-heating to commence.

G) Once ame is detected, the blue light on the Flame iQ

control box illuminates (7).

H) After ignition close the barbecue lid to enable

pre-heating to commence.

ON/OFF

RESET

Hold for

5 seconds

There are two ways to ignite the burner. The

rst is by using the ignition system built into

your barbecue. The second is with a match.

METHODS OF BURNER IGNITION

Flame iQ Q1000 & Q1200

Summary lighting instructions are on the

instruction tag of your barbecue and Flame iQ.

Only use this method if your ignition system is not

working.

Barbecue burner does not ignite.

Flame is low when burner control knob is on high ( )

position

If you are unable to solve a problem contact the service department who will assist with your enquiry.

PROBLEMS SOLUTIONS

TROUBLESHOOTING

m ATTENTION: This product has been safety tested and is only certiﬁed for use in a speciﬁc country. Refer to country designation

located on outer carton.

These parts may be gas carrying or gas burning components. Please contact Weber-Stephen Products LLC Customer Service

Department for genuine Weber-Stephen Products LLC replacement part(s) information.

m WARNING: Do not attempt to make any repair to gas carrying, gas burning, igniter components, or structural components without

contacting Weber-Stephen Products LLC Customer Service Department. Your actions, if you fail to follow this Product Warning,

may cause a ﬁre, an explosion, or structural failure resulting in serious personal injury or death as well as damage to property.

Weber-Stephen Products LLC

www.weber.com

1415 S. Roselle Road, Palatine, Illinois 60067 USA.

Weber-Stephen Products (Aust) Pty Ltd.

Level 1, 142-144 Fullarton Road

ROSE PARK SA 5067 AUSTRALIA

+61 8 8221 6111 | www.weberbbq.com.au

WEBER New Zealand ULC

86 East Highbrook Drive

East Tamaki, Auckland 2013 NEW ZEALAND

+64 9 279 7133 | www.WEBERnz.co.nz

Level 1, 142-144 Fullarton Road, Rose Park SA 5067 AUSTRALIA

The Flame iQ is covered by AU Patent 2021105238

These parts may be gas carrying or gas burning components.

ATTENTION: This product has been safety tested and is only certified for use in Australia and New Zealand.

WARNING: Do not attempt to make any repair to gas carrying or burning, igniter components, or structural components without contacting

Weber-Stephen Products Australia or New Zealand Customer Service Department. Your actions, if you fail to follow this Product Warning,

may cause a re, an explosion or structural failure resulting in serious personal injury or death as well as damage to property.

The WEBER Flame iQ contains no user serviceable

parts.

DO NOT MODIFY THIS PRODUCT

SERVICING SHALL ONLY BE CARRIED OUT BY

AUTHORISED PERSONNEL

For all Service needs contact:

Weber-Stephen Products (Aust) Pty Ltd

ABN 18 006 305 237

Level 1, 142-144 Fullarton Road, Rose Park SA 5067

Customer Service Ph: 1300 301 290 (toll free)

Email: custserv@weberbbq.com.au

Website: www.weber.com/au

Weber-Stephen Products New Zealand

86 East Highbrook Drive

East Tamaki, Auckland 2013

Customer Service Ph: 0800 493 237 (toll free)

Email: custserv@webernz.co.nz

Website: www.weber.com/nz

SERVICING & SPARE PARTS

Check the Flame iQ has power and is turned on (the ON/OFF button is illuminated green). When the Flame iQ is turned

on you will hear a soft click as the solenoid opens to let the gas through to the barbecue.

Fuel could be low or empty. Rell LPG cylinder.

Check burner ports under the sensor are clean.

Ensure barbecue is turned off, disconnect hose from LPG cylinder, wait 30 seconds and reconnect. Repeat ignition

procedure.

Ignitor fails to work. See page 7 for lighting instructions using a match.

Turn barbecue off, disconnect hose from LPG cylinder, wait 30 seconds and reconnect. Repeat ignition procedure.

Fuel could be low or empty. Rell LPG cylinder.

Fuel hose could be bent or kinked. Straighten fuel hose.

You have 30 seconds to ignite the barbecue after turning on the Flame iQ device. Refer burner ignition on page 7.

If the barbecue does not ignite, the Flame iQ will lock-out, the gas ow will stop, and the red reset light will illuminate.

Press the reset button for 5 seconds and it will turn off.

Press the ON/OFF button and repeat the ignition procedure.

Level 1, 142-144 Fullarton Road

Rose Park SA 5067 Australia

1300 301 290 (toll free) | www.weber.com/au

86 East Highbrook Drive

East Tamaki, Auckland 2013 New Zealand

0800 493 237 (toll free) | www.weber.com/nz

Weber-Stephen Products New Zealand

Weber-Stephen Products (Aust) Pty Ltd

Indice

Altri manuali Weber Unità di controllo

Weber

Weber Q 120 Guida

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente