WhatsGPS S06U Manuale utente
Model:S06U
User Manual
2G Vehicle GPS Tracker
Installation instructions
S06U - 1
Power line - 1
Relay - 1
Microphone - 1
SOS line - 1
User manual - 1
1) Wiring instructions
1. Accessories list
2. Installation instructions
2.1 SIM card installation
Confirm whether the accessories are complete before
using , including:
Open the face shell according to the instructions in
figure 1 and load the SIM card. The device USES the
SIM card of standard specification.
The device has three sets of interfaces, interface 1
for microphone connection, interface 2 for power
supply connection, and ACC detection and relay.
Interface 3 is used to connect the SOS keys. Interface
2 is a 4-core wire, which are relay wire (yellow), power
positive pole (red), power negative pole (black), and
ACC detection wire (green).
Notes for wiring
Interface description
1. The power supply range supported by the
equipment is 6-30v, please use the power cord
provided by the original factory. The red wire is the
positive pole and the black wire is the negative pole.
When installing the negative pole of the power supply,
please choose separate grounding or connecting the
iron.
1) ACC line (green line) is connected to the ACC
switch of the vehicle, and ACC line is used for
starting/flameout status detection of the vehicle.
2) The coil ends of the relay are respectively thin white
line (85) and thin yellow line (86), the thin white line is
connected to the positive of the automobile power
supply (+12V), and the thin yellow line is connected to
Port 1：Micphone
Port 2： Power/ACC/Relay
Port 3：SOS botton
Port 1
Port 2
Port 3
LED type State of
the LED meaning
Red
Slow flash
Positioning succeeded
Not located, searching for
satellite signal
Successfully connected to
the server
Successfully registered
GSM network
Slow
Flash
Bright
Bright
Blue
Trying to register GSM network
2. LED status indicator
3. Command setting instructions
the relay control line of the equipment. Cut the positive
line of the oil pump and connect it to the normally
closed section of the relay (coarse green line 87a)
and the other end to the common end of the relay
(coarse green line 30).
Note: this product is equipped with 12V relay, suitable
for 12V battery car.
By looking at the status indicator, we can know the
working status of the equipment. The status of the
indicator is as follows:
1) Set up the APN
Format 1: APN,[apnname]#
Format 2: APN,[apnname],[user],[password]#
Note: the device supports automatic APN setting, and
supports automatic switching of APN in most
countries. If the country or region cannot be switched
automatically, it can be switched by sending SMS.
Example: APN, cmnet#
2) Time zone setting
Format: GMT,[A],[B],[C]#
Note: the value of A is E or W, respectively
representing the eastern time zone and the western
time zone. B goes from 0 to 12, which is the time
zone. The value of C is 0,15,30,45 represents half
time zone, and the default is 0.
Example: GMT, E, 8, 0 #
3) Upload interval setting
Format: TIMER,[N]#
Note: the value of N is 10-65535 in seconds, and the
default escalation time interval is 10 seconds.
4) Center number setting
Format: CENTER,A,[NUM]#
CENTER number is set through the CENTER
instruction, which is used to send relay control
instructions. CENTER,D# is the instruction format for
removing the CENTER number.
Example: CENTER, A, 12345678901 #
Instruction format: CENTER,D#
Delete center number instruction.
Example: CENTER, D#
5) SOS setting
Format: SOS,A,[Num1],[Num2],[Num3]#
Instruction: set the SOS number through the SOS
instruction, the SOS number can receive the SOS
alarm information, and the remote listening can be
achieved by dialing the equipment number. Can set
1-3 Numbers,
Example: SOS,A,, 12345678911.
Example: SOS, A,
12345678910123567911123567912 # set said the
first, second and third number.
SOS,D,[A],[B],[C]#
Delete the format of SOS number, A, B and C are the
position Numbers of SOS number respectively, from
1-3.
Example: SOS,D,1,2,3# means delete 3 SOS
Example: SOS,D,3# means delete the third SOS
number.
Numbers.
6) Relay control setting:
Format: RELAY,[A]#
Note: the values of A are 0 and 1,1 means oil break, 0
means recovery. The relay is controlled and only the
central number can send the instruction.
Example: RELAY,1# send this instruction to realize
the cut-off of oil and electricity.
Example: RELAY,0# send this instruction to restore oil
and electricity.
Note: in order to ensure the safety of vehicles and
drivers, the device will only perform the power cut
function when the speed is less than 20KM/h under
the condition of effective GPS positioning.
7) Restore factory setting
Format: FACTORY#
This instruction reverts to factory default Settings.
8) Restart setting
Format: RESET#
Note: the system restart will be completed within 1
minute after the device receives the instruction.
4. Query setting
1) Parameter querying
Format: PARAM#
This instruction can be used to query the current
parameter Settings of the device.
Return information:
IMEI: 680915040900918; (device serial number)
IMEI: 680915040900918; (IMEI number)
APN: cmnet; (current APN)
IP: 47.90.83.185:8841; (current platform address and
port)
The TIMER: 20; (current upload interval)
CENTER: 123456789012; (current centre number)
TimeZone: 8-0; (current time zone)
LANG: EN. (language type)
LCWL: OFF; (local fence status)
Mode: 2; Protocol: GM; (current protocol type)
AutoSleep: DISABLE; (auto sleep function, supported
by some models)
2) Status querying
Format: STATUS#
Description: this instruction can query the current
working state of the device.
Return information:
EXT - POWER: 12.65 V. (current working voltage):
86%; (built-in battery indicator)
GPRS: NORMAL; (platform connection status,
NORMAL means connected, FAILED means not
connected)
The GSM Signal: H; (GSM signal value, H: high; M:; L:
low;)
GPS: Fixed; (GPS positioning status indicator, Fixed:
positioned, Invalid)
GPS Signal: L; (GPS signal value, H: high; M:; L: low;)
ACC: OFF; (ACC ignition status indicator, ON stands
for startup status, OFF stands for flameout status)
Fuel Supply: OFF (indicating the cut-off of oil/engine,
ON means the oil circuit is connected, OFF means the
oil circuit is broken)
3) Software version querying
Format: VERSION#
This instruction returns the software version
information of the device.
4) Latitude and longitude querying
Format: WHERE#
Description: this instruction returns the latest latitude
and longitude information of the device, for example:
Longitude Latitude: 23.00173:113.39463, Course: 0,
speed: 0.05 Km/h, Date: 2018-05-04, Time: 21:56:19
5) Latitude and longitude link querying
Format: URL#
Description: returns based on the map the location of
the link information, for example:
http://maps.google.com/maps? Q = 23.00153, 113.39459
Operation
4.1 Switch machine
After the device is loaded into the SIM card, it can be
powered on. If the device needs to be restarted, it
can be restarted after 10 seconds of power off.
4.2 View location
1) SMS Chinese address query.
2) latitude and longitude location SMS query.
3) latitude and longitude link SMS query.
4) platform mode query location.
4.3 SOS call the police
In case of emergency, press the SOS button for 3
seconds to trigger the SOS emergency alarm. The
device will send an alarm message to the service
platform. And send the longitude and latitude
information to the service platform. The platform will
send the Chinese address information analyzed by
the longitude and latitude information to the device,
which will send the Chinese alarm information to the
SOS number and call the SOS number.
To realize SOS alarm, set SOS number in advance
according to common instruction list.
4.4 Power off alarm
After the equipment is installed, a power off alarm will
Indice
Altri manuali WhatsGPS GPS
WhatsGPS
WhatsGPS S18 Manuale utente
WhatsGPS
WhatsGPS R11 Manuale utente
WhatsGPS
WhatsGPS W18L Manuale utente
WhatsGPS
WhatsGPS S5L Manuale utente
WhatsGPS
WhatsGPS S709 Manuale utente
WhatsGPS
WhatsGPS S100 Manuale utente
WhatsGPS
WhatsGPS S102 Manuale utente
WhatsGPS
WhatsGPS S116mini Manuale utente
WhatsGPS
WhatsGPS S102A Manuale utente
WhatsGPS
WhatsGPS S116mini Manuale utente
