Whip Mix VeriWash Manuale utente

USER MANUAL

3D PRINTED PARTS CLEANER

Whip Mix Corporation 361 Farmington Avenue Louisville, KY USA 40209

800- 626 -5651 502-637-1451 www.whipmix.com

VeriWash

VERIWASH User Manual Whip Mix Corporation

CONTENTS

1. Introduction .................................................2

1.1 Declaration of CE conformity ..............................2

1.2 Transport of the unit ......................................3

2. Components ................................................3

3. Technical Specications .......................................5

4. Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

5. Operation...................................................7

6. Cautions ....................................................8

7. Cleaning, Maintenance, and Care ..............................9

7.1 Cleaning.................................................9

7.2 Maintenance and Care ....................................9

8. Troubleshooting and Repair ..................................10

9. Environmental Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

10. Packaging ..................................................11

11. Warranty ..................................................11

VERIWASH User Manual Whip Mix Corporation

1. INTRODUCTION

Thank you for purchasing the VERIWASH automated cleaning unit. VERIWASH eciently

cleans uncured resin from 3D printed parts using isopropyl alcohol (Isopropanol). To ensure

that your VERIWASH gives you the highest level of performance, review and follow the

guidelines outlined in this User Manual and keep it for future reference.

Das Benutzerhandbuch ist auf www.whipmix.com in deutscher Sprache verfügbar.

Le manuel d'utilisation est disponible en français sur le site www.whipmix.com.

El manual del usuario se encuentra disponible en español en www.whipmix.com.

Il manuale utente è disponibile in italiano sul sitohttps://www.whipmix.com.

1.1 DECLARATION OF CE CONFORMITY

VERIWASH has been tested for CE marking according to the following European

Directive and standards:

Electromagnetic Compatibility Directive 2014/30/EU

EN 61326-1:2013, Class A (Basic Immunity)

EN 55011:2016 +A1:2017

EN 61000-3-2:2014

EN 61000-3-3:2013

EN 61010-1:2010 (Third Edition)

RoHS

EN 50581:2012

IEC 62321-3-1:2013

IEC 62321-8: 2017

1.2 TRANSPORT OF THE UNIT

Upon receipt of the VERIWASH, examine the shipment to determine whether

any items in the shipment are missing, defective or damaged. Notify Whip Mix

of any shortages, defects, or damage within 1 day of receipt of the shipment.

Within 10 days after the receipt of such notice, the company will take action

based on the ndings. Whip Mix will repair or replace any part proven defective

in material or workmanship at no charge.

VERIWASH User Manual Whip Mix Corporation

2. COMPONENTS

AC to DC Adapter with cable:

Provides power to the VERIWASH.

Main body (Base): Touch screen

displays the control interface with

the MODE, TIME, START and

STOP buttons. MODE button

selects which wash container to

use. Indicator lights shows which

wash container is selected.

Mesh Basket: The removable

basket is used to wash parts that are

unattached to the build platform.

The basket is inserted and secured

into the Wash Container to clean

the parts.

Universal Build Plate Jig /

Metal Rods: To clean printed

parts while they are attached to

the printer build plate, place the

Metal Rods (two of them) into the

appropriate slots of the Universal

Jig (adjustable positioning to t

build plate size up to 180mm ×

90mm) (7.08” × 3.54”).

VERIWASH User Manual Whip Mix Corporation

Wash Containers/Lids: There

are two separate removable

containers, each holding up to 3

liters of isopropanol. One is used for

the rst bath, and the second for a

second (fresh) bath. Each has its own

lid. A rotating impeller at the bottom

circulates the solvent.

Disposable Main Body Cover

(PET): Clear plastic cover is made

out of alcohol resistant material to

protect the main body of the unit

from spilled alcohol or resin.

3. TECHNICAL SPECIFICATIONS

MODEL: VERIWASH 3D PRINTED PARTS CLEANER

Product Dimensions: 24(L) × 24(W) × 35(H) cm (9.45” × 9.45” × 13.8”)

Package Dimensions: 29(L) × 29(W) × 52(H) cm (11.4” × 11.4” × 20.5”)

Product Weight: 3 kg (6.6 Ib)

Shipping Weight: 4.4kg (9.7 Ib)

Rated Power: 48W

Voltage: AC 100~240 V, ~50 / 60 Hz

Transient overvoltage: 2,500 V

VERIWASH User Manual Whip Mix Corporation

4. INSTALLATION

4.1 Place the Main Body (Base) on at surface.

NOTE: The disposable clear plastic cover is already in place.

This is a disposable item and can be changed if it becomes

soiled with spilled resin or alcohol.

4.2 Place each Wash Container on the Main Body. Be sure each ts well.

4.3 CAREFULLY ll the Wash Container with 2.5 - 3.0 liter of Isopropanol.

NOTE: It is recommended to dedicate one container as the

rst bath for the parts coming directly from the printer, and

the other container as a second bath, lled with fresh IPA

(ISOPROPANOL).

NOTE: Keep the Lid closed when the VERIWASH is not in use to

minimize the evaporation rate of the alcohol.

4.4 Use the Mesh Basket only to wash 3D printed parts not attached to the

printer build plate.

NOTE: To clean small 3D printed parts such as dies or single

crowns, there are two options as follows:

Put them into a 3” stainless steel tea ball infuser (not sold by

Whip Mix, can be purchased online), then insert into the mesh basket

as shown below.

For a 3D printer with a build plate size up to 180 mm x 90 mm (7.08”

x 3.54”), when not using the stainless steel tea ball infuser, keep the

printed parts attached to the build plate and use the Universal Build

Plate Jig as instructed in 4.5.

VERIWASH User Manual Whip Mix Corporation

4.5 Use the Universal Build Plate Jig and the Metal Rods to wash the printed

parts while they are attached to the build plate and the build plate size is up

to 180 mm x 90 mm (7.08” x 3.54”).

4.5.1 Position the Metal Rods in the slots of the Universal Jig based on the

size of your printer build plate.

NOTE: Check and adjust the position of the two Metal

Rods several times until the build plate is placed over

them securely.

4.5.2 Check the proper position of the build plate over the two Metal Rods,

set aside.

4.5.3 Insert the Universal Jig with the positioned Metal Rods inside the

Wash Container.

4.5.4 Secure the printer build plate over the positioned Metal Rods.

NOTE: Ensure printed parts are fully secured to the build

plate. Washing loose parts directly in the wash container

may damage printed parts, create noise, and interfere

with the impeller at the bottom.

4.6 Insert either the Mesh basket or the Universal Jig into the Wash Container

as instructed in 4.4 or 4.5.

4.7 Insert the AC cable into the receptacle in the back of the unit.

5. OPERATION

5.1. To turn on the unit, select and press the MODE button depending on which

Wash Container you want to operate - left, right, or both. LED (Blue) light

indicates which container is selected.

Left Right Both

5.2 Select the TIME (3 min, 5 min, or 10 min).

NOTE: Time cannot be changed while the cleaning cycle is in

progress.

5.3 Do not start the unit until the Containers, the Lid/Mesh Basket, and the

Universal Jig are all secured in their proper position.

VERIWASH User Manual Whip Mix Corporation

5.4 Press the START button to begin the wash cycle. The cleaning cycle will

operate for the length of time selected in the control interface. The impeller

reverses direction every 30 seconds.

NOTE: The speed at which the isopropyl alcohol is stirred is the

same for both Wash Containers and any cleaning duration

(3, 5, or 10 minutes).

5.5 To adjust the speed of BOTH containers, unit must be in OFF mode. Press

and hold the START and STOP button simultaneously for 5 – 7 seconds.

This will move you to the speed control mode.

To increase the speed: Press the START button repeatedly.

To decrease the speed: Press the STOP button repeatedly.

To save the speed: Press the MODE button.

NOTE: You cannot adjust the speed while the cleaning cycle is in

progress.

NOTE: To end the cleaning cycle before it is nished, press the

STOP button.

NOTE: When you press the STOP Button, it cancels the

remaining time of the wash cycle.

6. CAUTIONS

Before operating, read the VERIWASH USER MANUAL carefully. Follow the

instructions to avoid errors, equipment damage, or injury to the user.

Do not change the position of the Wash Container during operation.

Do not allow water or alcohol to get into the main body of the VERIWASH.

Ensure that no isopropyl alcohol spills when you ll the wash container at any time.

Spilled alcohol may damage the electronics or the base material.

Use only authorized accessories (power cord with appropriate rating).

Refer to the alcohol supplier safety data sheet (SDS) as the primary source of

information on the storage and handling of the alcohol.

Alcohol is ﬂammable and should be stored away from sources of ignition.

Wear gloves and handle alcohol in well-ventilated areas.

Alcohol evaporates quickly, so keep the lid(s) closed whenever possible.

Do not modify the unit. VERIWASH is intended to be used as directed only.

Keep away from children.

Do not operate with a damaged cord or plug. A damaged cord may only be replaced

by a power cord of the same type.

Only use well-maintained equipment.

Operate on a clear and at surface.

Always use the equipment in the safest possible manner.

Ensure that the Wash Containers, lids, and the mesh basket are all secured in their

proper positions before starting a cleaning cycle.

VERIWASH User Manual Whip Mix Corporation

7. CLEANING, MAINTENANCE, AND CARE

7.1 CLEANING

Always keep the main body clean from alcohol or resin. Keeping the

disposable cover on the main body at all times will protect the main

body from spilled alcohol

Always disconnect the power cable before cleaning/maintenance.

Remove the Wash Container from the base.

Remove the Universal Build Plate Jig, Mesh Basket, and Metal Rods

from the Wash Container.

Remove all alcohol from the Wash Containers.

Clean the inside of the Wash Containers with water, and wipe with

smooth clean cloth.

NOTE: Ensure that all water completely dries before

relling the container and operating.

Wipe the outer surface of the VERIWASH with Isopropyl alcohol or

water using a smooth clean cloth.

7.2 MAINTENANCE AND CARE

Isopropyl Alcohol

The Isopropyl alcohol should be changed periodically. Use up to

99% isopropyl alcohol.

The Isopropyl alcohol can be used for multiple cleaning cycles, but

the cleaning eectiveness of reused alcohol will decrease with each

cleaning cycle, depending upon the resin used and the printed part

geometry. In case of settling of solid polymerization residues, the

used alcohol must be changed immediately.

As Alcohol decreases over time due to use or evaporation, add

fresh alcohol to keep the right level of alcohol inside the wash

container.

Replace the alcohol when the wash is no longer eective and when

printed parts are tacky even after washing.

It is solely up to the operator to determine when the alcohol needs

to be changed.

Dispose of used Isopropyl alcohol per local and national

regulations.

Accessories can be replaced if needed. For purchasing accessories and

spare parts, visit WhipMix at shop.whipmix.com or www.whipmix.com.

VERIWASH User Manual Whip Mix Corporation

8. TROUBLESHOOTING AND REPAIR

VERIWASH has been designed to enable the user to replace parts or x the unit without

sending it anywhere. Replacement parts are readily available at www.shop.whipmix.com.

If problems do occur, consult the chart below. If additional information is needed, watch the

appropriate videos on the Whip Mix channel at www.youtube.com.

If still not satised, refer to the warranty agreement to determine your course of action. If

the unit is out of warranty, contact Whip Mix at (800) 626-5651.

Error Cause Solution

Loud noise High concentration of resin

in alcohol (viscosity change)

aects rotation speed

Adjust the speed – refer to the

operation process.

Unusual noise Obstruction in the Wash

Container

Check for loose parts or debris

on the bottom of the bucket.

Check that the impeller rotates

properly.

The Display doesn’t turn o Software issue Disconnect and reconnect the

power (restart).

The Display doesn’t turn on Software issue Disconnect and reconnect the

power after 1-2 min (restart).

Faulty electrical connection Check the power supply. Try

another outlet.

Disconnect and reconnect the

power.

Motor Jammed Misaligned impeller or debris

stuck around it

Check for loose printed parts

or debris stuck under the

impeller and remove it.

Check the impeller alignment

and proper rotation. Contact

Whip Mix for instruction.

9. ENVIRONMENTAL CONDITIONS

Installation: Indoor use

Altitude: up to 2,000 m

Operating temperature/humidity: 5–40°C / 20–80 %

Pollution degree: 2

Degree of protection: 1

Indice

Altri manuali Whip Mix Stampante 3D

Whip Mix

Whip Mix VeriBuild Manuale utente

Manuali Stampante 3D popolari di altre marche

Ultimaker

Ultimaker S5 Material Station Manuale utente

EcubMaker

EcubMaker TOYDIY Manuale utente

AnyCubic

AnyCubic Kossel Plus Manuale utente

ReDeTec

ReDeTec ProtoCycler Manuale utente

Kywoo3D

Kywoo3D Tycoon IDEX Manuale utente

CraftBot

CraftBot PLUS PRO Manuale utente

3DGence

3DGence INDUSTRY F340 Manuale utente

HP Jet Fusion 4200 Istruzioni operative

Rokit

Rokit AEP Series Manuale utente

AnkerMake

AnkerMake M5 Manuale utente

DIYElectronics

DIYElectronics PRUSA I3 Istruzioni per il montaggio

Ackuretta

Ackuretta FreeShape 120 Manuale utente

LONGER

LONGER LK5Pro Manuale utente

Stratasys

Stratasys J850 Manuale utente

MakerBot

MakerBot Replicator Manuale utente

Stratasys

Stratasys FDM Vantage Series Manuale utente

ZYYX

ZYYX Pro II Manuale utente

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Guida utente