Whirlpool 50 Manuale utente

CHANGING THE BIN DOOR PANEL

The storage bin door is designed to accept an

optional decorative wood panel of your choice.

The wood panel should be no more than ‘A inch

(6 mm) thick. Cut it to the same size as the

production metal panel. See Figure 1.

To change the panel:

1. Open the bin door.

2. Remove the two screws on top of the door

which hold the handle.

3. Remove the handle.

4. Slide the metal panel out.

5. Break off the ribs on the door insulation to

allow for the wood thickness. See Figure 2.

6. Slide the wood panel into the door frame.

7. Replace handle and screws.

13-3116” WOOD

PANEL

DIMENSIONS

REMOVE ALL DOOR INSULATION

RIBS TO ACCEPT WOOD PANEL

THICKNESS

FIGURE 2

THERMOSTAT CALIBRATIONS

If ice maker is installed above two thousand feet of

altitude, the bin and evaporator thermostats must

be adjusted to a warmer setting. Disconnect

electricity, remove thermostat and follow the

directions for turning the altitude adjustment

screw as shown in the label on each thermostat.

SHIPBOARD OPERATION

When this ice cube maker is installed aboard a ship,

it will be necessary to purchase and install a water

deflector. This deflector hangs between the lower

edge of the evaporator and the cutter grid. It keeps

the water flowing over the evaporator from spilling

into the storage bin area. Order the necessary parts

from your local ice maker dealer.

GENERAL INFORMATION

UNPACK

INTERIOR

PACKING

OPEN BOTTOM FLAPS

FIGURE 3 FIGURE 4

d Lay carton on rear face and break open bottom

flaps.

2 Set carton upright with all four flaps outward,

See Figure 3.

3 Lift container up and off of machtne.

4 Remove all tape and packaging material from the

outside and inside of the cabinet. See Figure 4.

5R emove the front grill; take out the screws secur-

ing the grill at the bottom and Ilft It free of cabinet.

Turn the fan by hand to make certarn It moves

freely.

?I- oosen thumb screws holding cutter grid and water

pan to “thumb tight.”

UTILITIES

WATER ELECTRICITY DRAIN

OBSERVE LOCAL CODES

Each installation is unique but will require:

2 Either a gravity drain system or a sump pump to flft

the water to an exrsting drain.

3 An electrical branch clrcult of 115 Volt, 60 Hz. 1

phase, with a 15 Amp delayed actron fuse.

. LOCATE UNIT

THIS UNIT MUST BE

INSTALLED IN AN

90' F

AREA PROTECTED FROM

THE ELEMENTS, SUCH

AS WIND, RAIN, WATER ‘03 F

SPRAY OR DRIP.

Lli ti6A

Place unrt so the front side

will

be completely

unobstructed. to provide proper air flow

2 Area should be well ventilated with temperature

above 55qF and below 110°F. Best results are

obtained between 70°F and 90°F.

3 Provrslon for electnclty. water and drain connec-

tions should be determined.

4 The unit may be closed in on the top and three

sides. but the front MUST BE unobstructed for air

circulation and proper operation lnstallatlon

should be such that the cabinet can be moved

forward for servlcrng If necessary

. LEVEL UNIT

After placrng untt In posltlon. check to make

certain

the

unrt

level side to side and front to

back

ccurate leveling

essential for proper operation

3 Unit should be shimmed so that It

solid as well as

level The shims should be of hard permanent type

matenal such as masonlte.

4 If required by sanitation code, seal the cabinet to

the floor wrth an approved caulking compound.

A cold water Inlet of 114”OD soft copper tubing and

a shut-off valve

FOR THE PLUMBER

CONNECT TO WATER SUMP PUMP

(observe local -codes)

Use

114”

OD soft copper tubing for the cold water

supply.

2 Provide a convenrent manual shut-off valve In the

water line.

3 Position the tub’ rng so it can enter the access hole

located in the right-hand rear of the cabinet. The

tubing should extend beyond the cabinet front

when the cabinet is pushed back into position. See

Figure 5.

NOTE:

Always purge the water line before making the final

connection to the inlet of the water valve to prevent

possible water valve malfunction.

After the cabinet is in place, bend the tubing to meet

the connection at the water valve. The garden hose

threaded compression fitting is found in the parts

bag. This joint provides a convenient disconnect for

service. Be sure the tubing is clear of compressor, to

prevent rattle.

CONNECT THE DRAIN

(observe local codes)

The unit IS provided with a gravtty drain.

2 The Ideal Installation has a standpipe

(llf4”

mlnrmum) Installed directly below the outlet of the

drain tube. Refer to Figure 5 for the proper location

of the standpipe.

3 It may be desirable to insulate drain line thoroughly

up to dram inlet.

When a drain connectlon below the level of the unit

IS not avallable. a sump pump may be used to Irft

the water to an avarlable drain

2 Install sump pump on floor behind ice maker with

discharge tube to the rear. Run bin drain directly

Into sump pump as shown In the Illustration.

NOTE:

Electric connection to sump pump should be from a

circuit that remains energized continually.

FIELD SUPPLIED

WATER LINE

THRU THIS HOLE.

RIGHT END VIEW

3/4.*-j +- 23.7/8”-1

d I

WATER INLET ’

SOLENOID ;

VALVE I

1/4”O.D. WATER

LINE COMPRESSION

VALVE

BEND FIELD SUPPLIED WATER LINE

TO CONNECT TO WATER VALVE FITTING

BACK VIEW

t- I

17.7/8”-

FIGURE 5

RUBBER

--- ..UN TO

IRAIN

FOR FIELD

ED WATER

3’ I

FOR THE ELECTRICIAN

ELECTRICAL REQUIREMENTS

A 115 Volt, 60 Hz, AC only, 15 Amp fused electrical supply IS

required (time delay fuse or circuit breaker is recommended).

It is recommended that a separate circuit, serving only this

appliance, be provided. DO NOT use an extension cord.

ELECTRICAL GROUND IS REQUIRED ON THIS

APPLIANCE.

RECOMMENDED

GROUNDING MtHOD

DO NOT, UNDER ANY CIRCUMSTANCES, REMOVE

THE POWER SUPPLY CORD GROUND PRONG.

For your personal safety, this appliance must be grounded.

This appliance is equipped with a power supply cord having a

3-prong grounding plug. To minimize possible shock hazard,

the cord must be plugged into a mating 3-prong grounding

type wall receptacle, grounded in accordance with the Natlonal

Electrical Code and local codes and ordinances. If a mating

wall receptacle is not available, it is the personal responslbillty

and obligation of the customer to have a properly grounded

3-prong wall receptacle installed bv a qualified electrician

See Figure 6

3-PRONG

GROUNDING TYPE

WALL RECEPTACLE II

III

NDING

\ POWER SUPPLY

CORD

FIGURE 6

ALTERNATE

GROUNDING METHOD

DO NOT, UNDER ANY CIRCUMSTANCES, REMOVE

THE POWER SUPPLY CORD GROUND PRONG.

If changing and properly grounding the wall recepta-

cle

lmposslble and where local codes permit

(consult your electrlcal inspector). a temporary

adapter may be plugged into the existing 2-prong wall

receptacle to mate with the 3-prong power supply

cord. See Figure 7. THIS, HOWEVER, IS NOT RE-

COMMENDED.

If this IS done, you musT connect the grouncllng eyelet on the

adapter to the wall receptacle cover plate screw and from this

same screw, you must connect a separate copper ground wire

(No 4 mlnimum) to a qrounded cold water pipe’ See Flgu:e

7 Do not ground to a gas supply pipe. Do not connect to

electrical supply until appliance IS permanently grounded.

-Cold water pipe must have melal contlnulty to electrIcal

ground and not be Interrupted by plastic rubber or other

electrIcally lnsulatlng connectors (including waler meter or

pump) wlthout addlng a lumper wire at these connectlons

GROUND ASSEMBLY

(ATTACH TO GROUNDED

COLD WATER PIPE)

ELECTRICALLY

GROUNDED COLD

WATER PIPE (REMOVE

GROUND WIRE (#4 i’llNlMUMl

GROUNDING

EYELET a

ASSEMBLY

POWER SUPPLY CORD

FIGURE 7

WALL

RECEPTACLE

HOW IT

WORKS THINGS TO

REMEMBER

0 Compressor runs

0 Condenser fan runs

0 Water pump runs (circulates water)

0 Cutter grid is warm to touch

WHEN THE DESIRED ICE SLAB

THICKNESS IS REACHED, THE

HARVEST CYCLE BEGINS AND THE

FOLLOWlNG HAPPENS:

0 Evaporator thermostat IS satisfied

0 Compressor keeps running

0 Condenser fan stops or turns very slowly

0 Water pump stops

0 Hot gas solenoid opens

0 Water inlet valve opens

0 Excess water is flushed out of the dram pan

0 Cutter grid is warm to the touch

NOTE:

Normal harvest cycle takes 60 to 120

seconds.

MACHINE RESUMES FREEZING AFTER

SLAB IS RELEASED FROM

EVAPORATOR AND THE CUlTlNG

PROCESS BEGINS.

WHEN THE STORAGE BIN IS FILLED,

BIN THERMOSTAT OPENS.

0 Cutter grid remains on

0 Water enters only during the defrost cycle. There-

fore the first cycle will be completed without

water in the system.

0 As the room and water temperatures vary, so will

the amount of ice produced. This means that

higher operating temperatures will result in re-

duced ice production.

0 The unit will shut off when ice in the storage bin

touches the bin thermostat well and will auto-

matically cycle to keep the bin full.

0 The storage bin is not refrigerated and some

meltage WIII occur. This, too, varies with the room

temperature.

0 The unit needs good air circulation to perform

efficiently. Keep the front grill and the condenser

clean.

0 The water system, including filter screen in the

water inlet solenoid valve, needs to be cleaned

periodically for good circulation. Instructions are

located on the inner door panel.

OPERATING

INSTRUCTIONS

0 For complete operating Information. refer to the

Use and Care Guide.

0 Before starting, wash out Intenor of cabinet with a

Baking Soda solution (2 tablespoons soda to a

quart of warm water). Rinse thoroughly.

0 Make certain the water is turned on

0 Turn switch to the “ON” position.

IMPORTANT:

Allow unit to run for 3 hours before expecting ice and

for 24 hours before trying to set the thickness

control.

If installed above 2,000 feet altitude, see page 2 for

thermostat adjustments.

UNIT WIRING DIAGRAM

This model operates at 115 volts except for the

cutter grid circuit which operates at 8.5 volts at 1

amp.

he compressor runs at all times except when the

bin thermostat becomes satisfied and opens up.

This de-energizes the system except for the trans-

former and cutter grid.

Under normal operating conditions, when the

evaporator reaches the preset temperature (+lO’

to -3O

F, depending on thickness of ice) the

evaporator thermostat opens, terminating op-

eration of the fan motor and pump motor. The

hot gas solenoid and the water valve solenoid are

energized at this time and remain so until the

evaporator reaches 38 + 2’ F.

DANGER:

ELECTRIC SHOCK HAZARD

DISCCNNECT

KhvER BEFORE SERVICIW LN,T

MAXIMUM FUSE SIZE: ISaMPs

NOTE‘CCWT.TS?+43’“4INFREEZINGCYCLE

FUSE GRID

YOUR UNIT MAY OR MAY NOT BE

EQUIPPED WITH A CUTTER GRID FUSE.

CUBELET CUTTER GRIDS

I-

CUBE CUTTER GRID

1%” x 1%” Cube Grid

”

CHECK OPERATION

Start the unrt by turnrng the service switch to

“ON” and opening the line water valve.

v NOTE: Left is “OFF” - Middle is “ON” - Right

is “CLEAN.” In

“CLEAN”

position, only the

pump operates.

v Check condenser fan to make sure it is revolving.

v Water will not enter pump pan until freezing

plate gets cold and machine goes into a harvest

cycle.

v Check for even water flow over freezing plate.

Unit must be level for proper operation.

v Check for desired cube thickness

and after 24

hours adjust if necessary. Maximum ice yield

will be obtained with ice thickness at J/2” to H”.

v Replace grill.

Quality. Our way of life.

Benlon Harbor Mlchlgan. Aulomallc Washers. Clothes Dryers

Freezers Relrlgeralor.Freezers Ice Makers. DIshwashers

Bu~ll-ln Ovens and Surlace Unlls. Ranges MIcrowave Ovens

Compaclors Aoom Air Condllloners Oehumldlllers Cenlral

Heallnq and Air Condlllonlng Syslems

Part No 756638-Rev A Printed in U.S.A

Indice

Altri manuali Whirlpool Macchina per il ghiaccio

Whirlpool

Whirlpool W11390949A Manuale utente

Whirlpool

Whirlpool EC510 Manuale utente

Whirlpool

Whirlpool AGB 022 Manuale utente

Whirlpool

Whirlpool IC13B Manuale utente

Whirlpool

Whirlpool MODULAR ICE MAKER KIT Manuale utente

Whirlpool

Whirlpool ECKMF-831 Manuale utente

Whirlpool

Whirlpool GI15NDXTB0 Manuale utente

Whirlpool

Whirlpool 50 Manuale utente

Whirlpool

Whirlpool EC5100 Manuale utente

Whirlpool

Whirlpool GI15NDXX Manuale elenco delle parti

Whirlpool

Whirlpool ECKMF-86 Manuale utente

Whirlpool

Whirlpool GI15NFRTS - INSTALLATION REV A Manuale utente

Whirlpool

Whirlpool AGB 024/01/G/WP Manuale utente

Whirlpool

Whirlpool CHE-12RC Manuale utente

Whirlpool

Whirlpool GI15NFRTB0 Manuale utente

Whirlpool

Whirlpool ECKMF-6 Manuale utente

Whirlpool

Whirlpool W10136155B Manuale utente

Whirlpool

Whirlpool ECKMF-28 Manuale utente

Whirlpool

Whirlpool VERSA CUBER CH E-5R Manuale utente

Whirlpool

Whirlpool GI15NDXTB - 15" 50 lb. Icemaker Manuale del proprietario

Whirlpool

Whirlpool Cornelius JEACS50SLF1 Manuale utente

Whirlpool

Whirlpool 2180913 Manuale utente

Whirlpool

Whirlpool ECKMF-83 Manuale utente

Whirlpool

Whirlpool 3EHC 50/51-1 Guida all'installazione

Manuali Macchina per il ghiaccio popolari di altre marche

Hoshizaki

Hoshizaki KMD-460MWJ Manuale utente

Sub-Zero

Sub-Zero 315I Istruzioni per l’uso

Unold

Unold 48945 Manuale utente

Kenmore

Kenmore 2217402A Manuale utente

Cornelius

Cornelius WM600 Istruzioni operative

GE XPIO43SCSS Manuale utente

Hoshizaki

Hoshizaki KMD-901MAH Manuale utente

Whynter

Whynter FIM-450HA Manuale utente

U-Line

U-Line UMCR014-SC01A Manuale di installazione

Andrew James

Andrew James AJ000522 Manuale utente

Scotsman

Scotsman CME1356 Manuale utente

Scotsman

Scotsman ACM 25 Manuale utente

Kärcher

Kärcher IP 120 Manuale utente

U-Line

U-Line SS1095 Manuale utente

Maytag

Maytag MIM1554WRS - Ice Maker Manuale utente

Hoshizaki

Hoshizaki KM-630MAH Manuale utente

Princess

Princess Yonanas Manuale utente

Unold

Unold 48946 Manuale utente