Wilson Electronics SIGNALBOOST 811210 Manuale utente

Amplifier

Installation

Guide

Warning: This manual contains

important safety and operating information.

Please read and follow the instructions

in this manual. Failure to do so could be

hazardous and result in damage to your

amplier.

SignalBoost™

Dual-Band

Cellular / PCS

Amplier

PART/MODEL# 811210

Contents:

Guarantee and Warranty · · · · · · · · · · · · · · · · · · · · · · · · 1

How it Works · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 2

Before Getting Started · · · · · · · · · · · · · · · · · · · · · · · · · · 3

Installation Overview · · · · · · · · · · · · · · · · · · · · · · · · · · · 3

Installing the Antenna (Vehicle) · · · · · · · · · · · · · · · · · · · 4

Installing the SignalBoost™ Amplier (Vehicle) · · · · · · · 5

Installing the Antenna (Home/Ofce) · · · · · · · · · · · · · · · 6

Installing the SignalBoost™ Amplier (Home/Ofce) · · · 6

Installing the Universal Connector · · · · · · · · · · · · · · · · · 7

Powering Up the Amplier · · · · · · · · · · · · · · · · · · · · · · · 8

Warnings and Recommendations · · · · · · · · · · · · · · · · · 9

About Wilson Electronics · · · · · · · · · · · · · · · · · · · · · · · · 10

Amplier Specications · · · · · · · · · · · · · · · · · · Back Cover

Wilson

Electronics, Inc.

30-Day Money-Back Guarantee

All Wilson Electronics products are protected by Wilson’s 30-day money-back

guarantee. If for any reason the performance of any product is not acceptable,

simply return the product directly to the reseller with a dated proof of purchase.

1-Year Warranty

Wilson Electronics ampliers are warranted for one (1) year against defects in

workmanship and / or materials. Warranty cases may be resolved by returning the

product directly to the reseller with a dated proof of purchase.

Ampliers may also be returned directly to the manufacturer at the consumer’s

expense, with a dated proof of purchase and a Returned Material Authorization

(RMA) number supplied by Wilson Electronics. Wilson shall, at its option, either

repair or replace the product. Wilson Electronics will pay for delivery of the repaired

or replaced product back to the original consumer.

This warranty does not apply to any ampliers determined by Wilson Electronics

to have been subjected to misuse, abuse, neglect, or mishandling that alters or

damages physical or electronic properties.

RMA numbers may be obtained by phoning Technical Support at 866-294-1660.

Operation is subject to the following two conditions: (1) This device may not cause

interference, and (2) this device must accept any interference, including interference that

may cause undesired operation of this device.

Disclaimer: The information provided by Wilson Electronics, Inc. is believed to

be complete and accurate. However, no responsibility is assumed by Wilson

Electronics, Inc. for any business or personal losses arising from its use, or for

any infringements of patents or other rights of third parties that may result from

its use.

Installation Instructions for the Following Wilson Amplier:

SignalBoost™ Dual-Band Cellular/PCS Amplier

Part / Model #811210

FCC ID: PWO819DA IC: 4726A-819DA

Patent Pending

The term “IC” before the radio certication number only signies that

Industry Canada technical specications were met.

Inside this Package

(antenna required - sold separately)

How it Works

Your new Wilson SignalBoost™ Amplier has been carefully engineered to signicantly

improve the performance of your cell phone or cellular data card in both vehicle and home/

ofce applications. Together with an antenna (sold separately), the amplier’s state-of-

the-art technology is designed to increase your signal up to 10 times, reduce disconnects

and dropouts, and increase data communication rates needed for 3G technologies. The

universal connector ts all cellular and PCS phones and data cards.

The antenna will collect the cell tower signal and send it through the cable to the amplier.

The signal is then boosted and sent through the extension cable to the universal connector

on your cell phone or data card, which then communicates with the improved signal. When

the cell phone or data card transmits, the signal goes through the universal connector

and the extension cable, is boosted by the amplier and broadcast back to the cell tower

through the antenna.

Wilson Electronics manufactures a wide variety of antennas and accessories to help you

customize your SignalBoost™ Amplier for your specic application. Several are shown

below. See your dealer or visit www.wilsonelectronics.com. NOTE: Use of this amplier

with an antenna gain higher than 6.12 dBi is in violation of FCC regulations for which the

offender is fully liable. All Wilson mobile antennas are 6.12 dBi or less.

SignalBoost™

amplier

12 V DC plug-in power

supply (vehicle)

Universal

connector

6‘ extension

cable

4-inch Mini

Magnet-Mount

Antenna

12-inch

Magnet-Mount

Antenna

Soft Carrying

Case

AC/DC Plug-In Power

Supply (home/ofce)

Window Bracket

Before Getting Started

This guide will help you properly install Wilson’s dual-band, SignalBoost™ amplier. It is

important to read through all of the installation steps for your particular application

prior to installing any equipment. Read through the instructions, visualize where all

the equipment will need to be installed and do a soft installation before mounting any

equipment. If you do not understand the instructions in full, please contact Wilson Technical

Support at 866-294-1660.

Installation Overview

The following steps provide a summary of the amplier/antenna installation process

using the optional mini magnet-mount antenna. However, they are not a substitute for the

complete installation instructions on the following pages, which you should read thoroughly.

If you are using a different antenna, follow the specic instructions that come with it.

STEP 1 Install the Antenna

For a vehicle installation, attach the antenna in the center of the vehicle’s roof and run the

cable through the door to the amplier. For a home or ofce installation, attach the antenna

to the optional window bracket, afx the bracket to a window with the suction cups and run

the cable to the amplier. (See pages 4 and 6 for details and RF safety warnings.)

STEP 2 Install the Amplier

Position the amplier in a well-ventilated location away from direct sunlight. Run the cable

from the antenna and attach it to the FME-Male connector labeled “outside antenna” on the

amplier. (See pages 5 and 6 for details.)

STEP 3 Attach the Universal Connector

Attach the universal connector cable to the FME-Male connector labeled “Universal

Connector” on the amplier. Attach the other end of the cable to your cell phone or cellular

data card with the supplied VELCRO®. (See page 7 for details.)

STEP 4 Power up the Amplier

IMPORTANT! Before connecting the power supply, ensure that both the antenna cable and

the universal connector cable are connected. (See page 8 for details.)

Mobile Installation Diagram Home/Ofce Installation Diagram

SIGNALBOOST™

Ampliﬁer

Cell Phone

Connection

Antenna

(sold separately)

Window Bracket

(sold separately)

AC Power Supply

(sold separately)

SIGNALBOOST™

Ampliﬁer

Laptop

Connection

Antenna

(sold separately)

Cigarette

Power Supply

SIGNALBOOST™

Ampliﬁer

Installing the Antenna

To receive the best cell signal, select a location in the center of the vehicle’s roof at least 12

inches away from any other antennas and free of obstructions.

The antenna must be installed vertically.

Signal performance will be degraded if the

antenna is not vertical.

The antenna cable may be run through the

door to the amplier.

The antenna cable is small enough to easily

tuck under the door seal or plastic molding.

For a more professional-looking installation,

the antenna cable may be run under the

door seal. Carefully pull down the door

seal. Run the cable through the seal

and push the seal back into place. This

prevents constant wear and tear on the

cable as the door opens and closes.

Carefully

Pull Down

Door Seal

Run Cable

Under

Seal

Tuck Cable

Under Seal

Vehicle Installation

Warning: The antenna used with this

amplier must have a separation distance of at

least 11 inches from all persons.

Installing the Wilson SignalBoost™ Amplier

Warning: Do not plug in the DC

power supply until the antenna and universal

connector cables are attached to the amplier.

Select a location to install the amplier that

is away from excessive heat, direct sunlight

or moisture and that has proper ventilation.

Recommended installation locations are:

• Under the seat

• Under the dash

Run the cable from the antenna and attach

it to the FME-Male connector labeled

“outside antenna” on the amplier.

Attach the universal connector cable to the

extension cable and attach the extension

cable to the FME-Male connector labeled

“Universal Connector” on the amplier.

Then attach the universal connector to your

cell phone or data card.

Vehicle Installation

Installing the Antenna

To receive the best cell signal, select a window location at least 12 inches away from any

radio or television antennas and free of obstructions.

Using the suction cups, position the

mounting bracket on the window at a height

convenient to where the amplier will be

located, then attach the antenna to the

bracket.

The antenna must be installed vertically.

Signal performance will be degraded if the

antenna is not vertical.

Select a location to install the amplier that

is away from excessive heat, direct sunlight

or moisture and that has proper ventilation.

Recommended installation locations are:

• On a desk or table top

• In a bookshelf

• On the oor

Run the cable from the mini magnet-mount

antenna and attach it to the FME-Male

connector labeled “outside antenna” on the

amplier.

Attach the universal connector cable to the

extension cable and attach the extension

cable to the FME-Male connector labeled

“Universal Connector” on the amplier.

Then attach the universal connector to your

cell phone or data card.

Home/Ofce Installation

Installing the Wilson SignalBoost™ Amplier

Warning: Do not plug in the AC power

supply until the outside antenna and universal

connector cables are attached to the amplier.

Warning: The antenna used with this

amplier must have a separation distance of at

least 11 inches from all persons.

Installing the Wilson Universal Connector

The universal connector must be placed

directly on the cell phone or cellular data

card to work properly. Attach the universal

connector to the cell phone or cellular data

card with the VELCRO®included in the

package.

The universal connector and extension

cable included in the package are long

enough to reach the amplier location. This

allows for ease and convenience of use.

To adjust the universal connector for the

best signal, go to a weak signal location

where your cell phone registers only 1-2 bars

without the universal connector connected.

(Be sure the amplier is turned off when

checking for low signal.) Then, attach the

universal connector to the phone, power up

the amplier and you should see a signal

improvement of 2 or more bars.

Note: Many phones take up to 20 seconds

to reset the bar indicator.

To maximize performance, attach the universal

connector as close as possible to the original

antenna on your cell phone or cellular data card.

For cell phones with no external antenna, place

the universal connector on the back, upper left-

hand corner of the phone. (Figure 1)

For cell phones with an external antenna, place

the universal connector directly below the

phone’s original antenna. (Figure 2)

Many of the hands-free cradles have a built-in

antenna with a pigtail. If using a hands-free

device or cell phone cradle, the universal

connector may be directly connected to the

phone cradle or to the pigtail.

Amplier 6’ Extension

Cable Universal

Connector

Figure 1 Figure 2

To Amplier

Cellular data card

Powering up the Amplier

Make sure both the outside antenna and

universal connector cables are connected

before powering up the amplier.

For vehicle use, connect the power cable

from the DC plug-in power supply to the

amplier input marked “Power” and insert

the large end into DC power socket (the

cigarette lighter outlet).

For home or ofce use, connect the cable

from the AC/DC plug-in power supply (sold

separately) to the amplier input marked

“Power” and insert the plug end into a

standard wall outlet.

The amplier may remain on all the time.

However, leaving the amplier on in a

vehicle when it is not running can discharge

the battery in a day or two.

A good option is to power the amplier

through the ignition switch so the amplier

is turned on and off with the vehicle.

NOTE: The aluminum casing of the SignalBoost™ amplier will adjust very quickly to the

ambient temperature of its environment. For example, in the summer, when the inside of

a car can reach 140 degrees Fahrenheit, the amplier temperature may be 150 degrees

or higher. The casing will be hot to the touch, similar to a metal door handle or steering

wheel. Such high temperatures will not damage the amplier, nor do they pose a re risk.

As recommended in these instructions, when installing the amplier in a vehicle, select a

location with adequate ventilation, such as under the seat or dashboard. Keep the area

free of items that could block air ow to the amplier.

Carefully insert the power cable.

IMPORTANT: Do not power up the

amplier unless the antenna and universal

connector cables are attached to the

amplier.

Warning: Use only Wilson power

supply units. Use of a non-Wilson

product may damage your equipment.

12 V DC power supply (included)

AC/DC power supply (not included)

Warnings and Recommendations

Warning: Do not plug the amplier directly into the cell phone or cellular

data card using an antenna adapter. It will damage the cell

phone or cellular data card.

Warning: Do not plug in the power supply until the antenna and universal

connector cables are attached to the amplier.

Warning: RF Safety: The antenna must be installed with a separation of

at least 11 inches from nearby persons and must not be located

or operating in conjunction with any other antenna or amplier.

Use of this amplier with an antenna gain higher than 6.12 dBi

is in violation of FCC regulations for which the offender is fully

liable. All Wilson mobile antennas are 6.12 dBi or less.

Recommended amplier installation locations for a vehicle are:

• Under the seat

• Under the dash

Power the amplier through the ignition switch so the amplier is turned on and

off with the vehicle.

Recommended amplier installation locations for a home or ofce are:

• On a desk or table top

• In a bookshelf

• On the oor

Altri manuali per SIGNALBOOST 811210

Indice

Altri manuali Wilson Electronics Amplificatore

Wilson Electronics

Wilson Electronics 271245 Manuale utente

Wilson Electronics

Wilson Electronics 801105 Manuale utente

Wilson Electronics

Wilson Electronics SIGNALBOOST C-Booster Manuale utente

Wilson Electronics

Wilson Electronics 801247 Manuale utente

Wilson Electronics

Wilson Electronics 271245 Manuale utente

Wilson Electronics

Wilson Electronics iDEN Manuale utente

Wilson Electronics

Wilson Electronics 2B1401 Manuale utente

Wilson Electronics

Wilson Electronics WILSONPRO ENTERPRISE 4300 Manuale utente

Wilson Electronics

Wilson Electronics PRO 710i Manuale utente

Wilson Electronics

Wilson Electronics 801230 Manuale utente

Wilson Electronics

Wilson Electronics 271245 Manuale utente

Wilson Electronics

Wilson Electronics 801105 Manuale utente

Wilson Electronics

Wilson Electronics SignalBoost DT Manuale utente

Wilson Electronics

Wilson Electronics SignalBoost DT Manuale utente

Wilson Electronics

Wilson Electronics BD800AM-M Manuale utente

Wilson Electronics

Wilson Electronics 811101 Manuale utente

Wilson Electronics

Wilson Electronics 814001 Manuale utente

Wilson Electronics

Wilson Electronics SignalBoost Manuale utente

Wilson Electronics

Wilson Electronics 271220 Manuale utente

Wilson Electronics

Wilson Electronics 801102 Manuale utente

Wilson Electronics

Wilson Electronics WILSONPRO PRO 140i Manuale utente

Wilson Electronics

Wilson Electronics WILSONPRO ENTERPRISE 4300R Manuale utente

Wilson Electronics

Wilson Electronics U-Booster 2B5225 Manuale utente

Wilson Electronics

Wilson Electronics 271247-50 Manuale utente

Manuali Amplificatore popolari di altre marche

ASTRO

ASTRO HVO V40 P Manuale utente

Marantz

Marantz SUPERSCOPE BLA-545 Istruzioni per il montaggio

NAD

NAD CI980 Manuale utente

Technics

Technics SE-CH770 Manuale utente

Harman Kardon

Harman Kardon HK6300 Manuale utente

NAD

NAD T975 Manuale utente

McIntosh

McIntosh MA6850 Manuale utente

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manuale utente

Viatron

Viatron Autrix Manuale utente

GME

GME GA9800 Manuale utente

Atlas

Atlas CP700 Manuale utente

Roland

Roland KC-1000 Manuale utente

Pyle

Pyle PFMRA350BW Manuale utente

Advantage

Advantage S-250 Manuale utente

IRT Electronics

IRT Electronics DVA-3007 Manuale utente

Dimavery

Dimavery BA-100 Series Manuale utente

Sony

Sony XM-S400D Manuale utente

Schertler

Schertler ROY X Manuale utente